$ sudo modprobe Intel537 On Fri, Feb 25, 2011 at 6:58 PM, Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx> wrote: > Scott, > > Unload Âuseless slmodem driver > $ sudo modprobe -r slamr > Load the Intel driver > $ sudo Intel537 > Then again: > $ sudo wvdialconf > > MarvS > > > On Fri, sb 25, 2011 at 6:41 PM, Scott Cink <cinktech@xxxxxxxxx> wrote: >> Thanks, >> >> I ran wvdialconf with root permission with the same results: >> >> smcink@ubuntu:~/Downloads$ sudo wvdialconf >> [sudo] password for smcink: >> Editing `/etc/wvdial.conf'. >> >> Scanning your serial ports for a modem. >> >> ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud >> ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud >> ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. >> ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud >> ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud >> ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. >> Modem Port Scan<*1>: S2 Â S3 >> >> >> Sorry, no modem was detected! ÂIs it in use by another program? >> >> >> On Fri, Feb 25, 2011 at 4:32 PM, Marvin Stodolsky >> <marvin.stodolsky@xxxxxxxxx> wrote: >>> Scott >>> >>> RE: Â$ wvdialconf >>> Must be done with Root permission >>> $ sudo wvdialconf >>> >>> Also, you have installed the slmodem support, which is useless for >>> your Intel537 modem >>> >>> MarvS >>> >>> On Fri, Feb 25, 2011 at 3:25 PM, Scott Cink <cinktech@xxxxxxxxx> wrote: >>>> Hello, I am new to Ubuntu and am trying to set up my fax modem. ÂI >>>> have installed the drivers from here: >>> >>>> http://groups.google.com/group/ubuntu-modems/web/intel536ep-maverick_1-Philippe.Vouters_i386.deb >>>> >>>> and when I run wvdialconf I get: >>>> >>>> smcink@ubuntu:~$ wvdialconf >>>> Editing `/etc/wvdial.conf'. >>>> >>>> Scanning your serial ports for a modem. >>>> >>>> WvModem<*1>: Cannot set information for serial port. >>>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud >>>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud >>>> ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. >>>> WvModem<*1>: Cannot set information for serial port. >>>> ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud >>>> ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud >>>> ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. >>>> Modem Port Scan<*1>: S2 Â S3 >>>> >>>> >>>> Sorry, no modem was detected! ÂIs it in use by another program? >>>> >>>> -- >>>> >>>> What should I do next? >>>> >>> >> >
