havealoha, scanModem reports that your modem is supported through SLMODEMD.gcc4.4-alsa-1.0.21.tar.gz. Did you download the following package: Download from http://linmodems.technion.ac.il/packages/smartlink/ the package SLMODEMD_gcc4.4_alsa1.0.21.tar.gz Predictive diagnostics for card in bus 00:1b.0: Modem chipset detected on NAME="Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller " CLASS=0403 PCIDEV=8086:27d8 SUBSYS=107b:0366 IRQ=22 HDA2=00:1b.0 SOFT=8086:27d8.HDA HDAchipVendorID=1057 CHIP=0x10573057 IDENT=slmodemd SLMODEMD_DEVICE=hw:0,6 Driver=snd-hda-intel For candidate modem in: 00:1b.0 0403 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller Primary device ID: 8086:27d8 Subsystem PCI_id 107b:0366 Softmodem codec or chipset from diagnostics: 0x10573057 from Archives: The HDA card softmodem chip is 0x10573057 Support type needed or chipset: slmodemd supporting the snd-hda-intel audio+modem driver An ALSA (Advanced Linux Sound Architecture) modem driver: snd-hda-intel provides Low Level support enabling contact with the modem hardware. For all BUT Conexant chip soft modems (using hsfmodem software) complementary High Level support is through a Smartlink utility: slmodemd Download from http://linmodems.technion.ac.il/packages/smartlink/ the package SLMODEMD_gcc4.4_alsa1.0.21.tar.gz having a compiled slmodemd. Unpack under Linux with: $ tar zxf SLMODEMD_gcc4.4_alsa1.0.21.tar.gz and read instructions therein. But briefly, the modem is setup with command: sudo slmodemd -c YOUR_COUNTRY --alsa hw:0,6 reporting dynamic creation of ports: /dev/ttySL0 --> /dev/pts/N , with N some number Read DOCs/Smartlink.txt and Modem/DOCs/YourSystem.txt for follow through guidance. Regards, Antonio On Tue, Nov 9, 2010 at 11:42 AM, havealoha <havealoha@xxxxxxxxx> wrote: > From my understanding I am using an Smart Link Si3054 Modem that > shares resources with my Intel ICH 7 audio card. > > My speakers / sound / microphone does work. I have no idea if the > modem works because I have no POTS copper, magicjack or VoIP device to > provide a dialtone to the modem. > > > What I am trying to accomplish is to send a fax using the capabilities > of efax-gtk, slmodemd, alsa and my smart link modem to route the > "sound" of the fax through to the line in / microphone of my soundcard > so that it gets sent over whatever software phone I choose in the GUI. > > So its like I want to trick the modem into thinking its plugged in so > the fax software will make the faxing sounds and route that sound to > line in. > > Feasible right? With the right error correction and baud rate? > > First off, can anyone tell me that this is possible? > Second, from looking at my ModemData / scanModem output is everything > installed / setup properly? > And finally, what do I do? Some fancy .asoundrc pcm name routing? > > Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List Server, > as HTML can contain viruses. Use as the email Subject Line: > YourName, YourCountry kernel 2.6.32-25-generic > With this Subject Line cogent experts will be alerted, and useful > case names left in the Archive. > YourCountry will enable Country specific guidance. Linux experts in YourCountry > can be found through: http://www.linux.org/groups/index.html. > They will know your Country's modem code, which may be essential for > dialup service. > Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an > Internet Provider mail filters. > So in a day, also check the Archived responses at http://www.linmodems.org > -------------------------- System information ---------------------------- > CPU=i686, Ubuntu , ALSA_version=1.0.21 > Linux version 2.6.32-25-generic (buildd@palmer) (gcc version 4.4.3 > (Ubuntu 4.4.3-4ubuntu5) ) #45-Ubuntu SMP Sat Oct 16 19:48:22 UTC 2010 > scanModem update of: 2010_05_29 > The modem symbolic link is /dev/modem -> ttySL0 > The slmodemd set symbolic link is /dev/ttySL0 -> /dev/pts/2 > Distrib_ID=Ubuntu > DistribCodeName=lucid > AptRepositoryStem=http://us.archive.ubuntu.com/ubuntu/ > > > The dkms driver upgrade utilities are installed, > > There are no blacklisted modem drivers in /etc/modprobe* files > > Potentially useful modem drivers now loaded are: > snd_hda_intel > > Attached USB devices are: > ID 0a5c:2154 Broadcom Corp. > ID 0a5c:4503 Broadcom Corp. > ID 0a5c:4502 Broadcom Corp. > ID 0a5c:4500 Broadcom Corp. BCM2046B1 USB 2.0 Hub (part of BCM2046 Bluetooth) > ID 04a9:173e Canon, Inc. > If a cellphone is not detected, see > http://ubuntuforums.org/archive/index.php/t-878554.html > A sample report is: > http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html > > If a USB modem or cellphone is attached and was not detected, please > provide available information in your request to discuss@xxxxxxxxxxxxx > > Candidate PCI devices with modem chips are: > 00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High > Definition Audio Controller (rev 02) > High Definition Audio cards can host modem chips. > > For candidate card in slot 00:1b.0, firmware information and bootup > diagnostics are: > PCI slot PCI ID SubsystemID Name > ---------- --------- --------- -------------- > 00:1b.0 8086:27d8 107b:0366 Audio device: Intel Corporation > N10/ICH 7 Family High Definition Audio Controller > > Modem interrupt assignment and sharing: > 22: 34379 0 IO-APIC-fasteoi HDA Intel > --- Bootup diagnostics for card in PCI slot 00:1b.0 ---- > > > ===== Advanced Linux Sound Architecture (ALSA) diagnostics ===== > The ALSA packages provide audio support and also drivers for some modems. > ALSA diagnostics are written during bootup to /proc/asound/ folders. > > The modem cards detected by "aplay -l" are: > card 0: Intel [HDA Intel], device 6: Si3054 Modem [Si3054 Modem] > > The /proc/asound/pcm file reports: > ----------------------- > 00-00: STAC92xx Analog : STAC92xx Analog : playback 1 : capture 1 > 00-06: Si3054 Modem : Si3054 Modem : playback 1 : capture 1 > > about /proc/asound/cards: > ------------------------ > 0 [Intel ]: HDA-Intel - HDA Intel > HDA Intel at 0xd8240000 irq 22 > > PCI slot 00:1b.0 has a High Definition Audio Card > The drivers are in the kernel modules tree at: > /lib/modules/2.6.32-24- > generic/kernel/sound/pci/hda/snd-hda-intel.ko > /lib/modules/2.6.32-25-generic/kernel/sound/pci/hda/snd-hda-intel.ko > The modem codec file for the HDA card is: /proc/asound/card0/codec#1 > -------------------------------------------------------- > Codec: Motorola Si3054 > Address: 1 > Function Id: 0x2 > Vendor Id: 0x10573057 > Subsystem Id: 0x00010001 > Revision Id: 0x100100 > Modem Function Group: 0x1 > > The audio card hosts a softmodem chip: 0x10573057 > > The softmodem chip 0x10573057 is in principle supported by the COMM > support of slmodemd > and the joint snd-hda-intel audio+modem driver, begun with ALSA version 1.0.13. > For HDA cards with ALC883 chips, an upgrade to ALSA verions 1.0.15 way > be necessary. > Instructions for Upgrading snd-hda-intel and its dependent driver set are at: > http://linmodems.technion.ac.il/bigarch/archive-eighth/msg00838.html > > If not a Conexant modem, the driver snd-hda-intel with its dependent drivers: > snd_hda_intel 22037 5 > snd_hda_codec 74201 3 > snd_hda_codec_si3054,snd_hda_codec_idt,snd_hda_intel > snd_pcm 70694 6 > snd_hda_codec_si3054,snd_hda_intel,snd_hda_codec,snd_pcm_oss > snd 54180 21 > snd_hda_codec_si3054,snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device > snd_page_alloc 7076 2 snd_hda_intel,snd_pcm > ---------- > provide audio + modem support with the modem chip residing on the subsystem. > Any particular card can host any one of several soft modem chips. > > === Finished firmware and bootup diagnostics, next deducing cogent software. === > > Predictive diagnostics for card in bus 00:1b.0: > Modem chipset detected on > NAME="Audio device: Intel Corporation N10/ICH 7 Family High Definition > Audio Controller " > CLASS=0403 > PCIDEV=8086:27d8 > SUBSYS=107b:0366 > IRQ=22 > HDA2=00:1b.0 > SOFT=8086:27d8.HDA > HDAchipVendorID=1057 > CHIP=0x10573057 > IDENT=slmodemd > SLMODEMD_DEVICE=hw:0,6 > Driver=snd-hda-intel > > For candidate modem in: 00:1b.0 > 0403 Audio device: Intel Corporation N10/ICH 7 Family High > Definition Audio Controller > Primary device ID: 8086:27d8 > Subsystem PCI_id 107b:0366 > Softmodem codec or chipset from diagnostics: 0x10573057 > from Archives: > The HDA card softmodem chip is 0x10573057 > > > Support type needed or chipset: slmodemd supporting the > snd-hda-intel audio+modem driver > > An ALSA (Advanced Linux Sound Architecture) modem driver: snd-hda-intel > provides Low Level support enabling contact with the modem hardware. > For all BUT Conexant chip soft modems (using hsfmodem software) > complementary High Level support is through a Smartlink utility: slmodemd > > Download from http://linmodems.technion.ac.il/packages/smartlink/ > the package SLMODEMD_gcc4.4_alsa1.0.21.tar.gz having a compiled > slmodemd. Unpack under Linux with: > $ tar zxf SLMODEMD_gcc4.4_alsa1.0.21.tar.gz > and read instructions therein. But briefly, the modem is setup with command: > sudo slmodemd -c YOUR_COUNTRY --alsa hw:0,6 > reporting dynamic creation of ports: > /dev/ttySL0 --> /dev/pts/N , with N some number > Read DOCs/Smartlink.txt and Modem/DOCs/YourSystem.txt for follow > through guidance. > > > Writing DOCs/Intel.txt > Writing DOCs/Smartlink.txt > ============ end Smartlink section ===================== > > Completed candidate modem analyses. > > The base of the UDEV device file system is: /dev/.udev > > Versions adequately match for the compiler installed: 4.4.3 > and the compiler used in kernel assembly: 4.4.3 > > > > Minimal compiling resources appear complete: > make utility - /usr/bin/make > Compiler version 4.4 > linuc_headers base folder /lib/modules/2.6.32-25-generic/build > > However some compilations and executable functions may need additional files, > in the FileNames.h (so called kernel "h"eaders) collection installed > in /usr/include/ . > For martian_modem, additional required packages are needed. The also > required headers of package libc6 are commonly installed by default. > Compiling hsfmodem drivers does require linux-libc-dev and libc6-dev > packages, for kernels 2.6.24 and later versions. > In not included on your install CD, search for them at > http://packages.ubuntu.com > or comparable Repository for other Linux distros. > When compiling ALSA drivers, the utility "patch" will also be needed. > > > Compressed files at: /usr/src/linux-source-2.6.32.tar.bz2 > > > If a driver compilation fails, with message including some lack of > some FileName.h (stdio.h for example), then > Some additional kernel-header files need installation to /usr/include. > The minimal additional packages are libc6-dev > and any of its dependents, under Ubuntu linux-libc-dev > > If an alternate ethernet connection is available, > $ apt-get update > $ apt-get -s install linux-kernel-devel > will install needed packages. > For Debian/Ubuntu related distributions, run the following command to > display the needed package list: > > Otherwise packages have to be found through http://packages.ubuntu.com > Once downloaded and transferred into a Linux partition, > they can be installed alltogether with: > $ sudo dpkg -i *.deb > > > Checking pppd properties: > -rwsr-xr-- 1 root dip 273312 2010-03-06 19:59 /usr/sbin/pppd > > In case of an "error 17" "serial loopback" problem, see: > http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html > > To enable dialout without Root permission do: > $ su - root (not for Ubuntu) > sudo chmod a+x /usr/sbin/pppd > or under Ubuntu related Linuxes > sudo chmod a+x /usr/sbin/pppd > > Checking settings of: /etc/ppp/options > asyncmap 0 > noauth > crtscts > lock > hide-password > modem > proxyarp > lcp-echo-interval 30 > lcp-echo-failure 4 > noipx > > In case of a message like: > Warning: Could not modify /etc/ppp/pap-secrets: Permission denied > see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html > > For guidance on FAX usage, get from > http://linmodems.technion.ac.il/packages/ get faxing.tar.gz > It has samples for a modem using port /dev/ttySL0, which must be > changed to match your modem's port. > > Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0 eth1 > Which can interfere with Browser naviagation. > > Don't worry about the following, it is for experts should trouble > shooting be necessary. > ========================================================== > > Checking for modem support lines: > -------------------------------------- > /device/modem symbolic link: lrwxrwxrwx 1 root root 6 > 2010-11-04 16:16 /dev/modem -> ttySL0 > slmodemd created symbolic link /dev/ttySL0: lrwxrwxrwx 1 root root 10 > 2010-11-04 21:31 /dev/ttySL0 -> /dev/pts/2 > Within /etc/udev/ files: > > Within /etc/modprobe.conf files: > /etc/modprobe.d/blacklist-modem.conf:# Uncomment these entries in > order to blacklist unwanted modem drivers > /etc/modprobe.d/blacklist-modem.conf:# blacklist snd-atiixp-modem > /etc/modprobe.d/blacklist-modem.conf:# blacklist snd-via82xx-modem > /etc/modprobe.d/alsa-base.conf:options snd-atiixp-modem index=-2 > /etc/modprobe.d/alsa-base.conf:options snd-via82xx-modem index=-2 > /etc/modprobe.d/sl-modem.conf:install slamr /sbin/modprobe -qb > ungrab-winmodem; /sbin/modprobe --ignore-install slamr; test -e > /dev/slamr0 && (chmod 660 /dev/slamr0 && chgrp dialout /dev/slamr0) || > (/bin/mknod -m 660 /dev/slamr0 c 242 0 2>/dev/null && chgrp dialout > /dev/slamr0) > /etc/modprobe.d/sl-modem.conf:install slusb /sbin/modprobe -qb > ungrab-winmodem; /sbin/modprobe --ignore-install slusb; test -e > /dev/slusb0 && (chmod 660 /dev/slusb0 && chgrp dialout /dev/slusb0) || > (/bin/mknod -m 660 /dev/slusb0 c 243 0 2>/dev/null && chgrp dialout > /dev/slusb0) > Within any ancient /etc/devfs files: > > Within ancient kernel 2.4.n /etc/module.conf files: > > --------- end modem support lines -------- >
