Re: Fw: Progress !

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello,

So, who could help me to make this modem working ?
I installed teh alsa driver linuxant

Thank.

Hi,

note that with a Conexant HDA modem, installing alsa-driver-linuxant:

http://www.linuxant.com/alsa-driver/

might also be necessary.

Regards,


Jonathan
Technical specialist / Linuxant
www.linuxant.com
support@xxxxxxxxxxxx


Patrick Dupre wrote:
On Sun, 19 Sep 2010, Antonio Olivares wrote:

Folks,

I am trying to help Patrick get connected with Fedora 13 using conexant modem.


Patrick,

did you get the driver:

http://www.linuxant.com/drivers/hsf/full/archive/hsfmodem-7.80.02.06full/hsfmodem-7.80.02.06full-1.i386.rpm.zip

YES

If you did, then did you install with

YES

METHOD A: BINARY RPM PACKAGE (*.{arch}.rpm)
If you have obtained the driver package in RPM format: 1. install the rpm with "rpm -i hsfmodem-{version}.{arch}.rpm" 2. if necessary, run "hsfconfig" to complete the installation, enter license information, or to change your modem's configuration.

If you need to rebuild the generic RPM from source, you can get the TAR package and run: "rpmbuild -tb hsfmodem-{version}.tar.gz" (if rpmbuild is not found, you might have to install the rpm-build package or if you have an older RPM version, try "rpm --rebuild ..."). If you want a pre-compiled package for the currently running kernel, you can try "make rpmprecomp" in the top directory.

 as provided in instructions here:
 http://www.linuxant.com/drivers/hsf/install.php
You have installed the driver successfully because the lines show something:
 /etc/udev/rules.d/00-hsf.rules:KERNEL=="ttySHSF0", SYMLINK="modem"
    Within /etc/modprobe.conf files:
/etc/modprobe.conf:install snd-via82xx-modem /bin/true # temporarily disabled by hsf - conflicts with hsfmc97via /etc/modprobe.conf:install snd-atiixp-modem /bin/true # temporarily disabled by hsf - conflicts with hsfmc97ati
/etc/modprobe.conf:alias /dev/modem /dev/ttySHSF
/etc/modprobe.conf:install /dev/ttySHSF /sbin/modprobe hsfpcibasic2; /sbin/modprobe hsfpcibasic3; /sbin/modprobe hsfmc97ich; /sbin/modprobe hsfmc97via; /sbin/modprobe hsfmc97ali; /sbin/modprobe hsfmc97ati; /sbin/modprobe hsfmc97sis; [ -e /lib/modules/`uname -r`/extra/hsfusbcd2.ko ] && /sbin/modprobe hsfusbcd2; /sbin/modprobe snd_hda_intel; [ -e /lib/modules/`uname -r`/extra/snd-hda-codec-hsfmodem.ko ] && /sbin/modprobe snd-hda-codec-hsfmodem; /bin/true
    Within any ancient /etc/devfs files:

    Within ancient kernel 2.4.n /etc/module.conf files:
alias /dev/modem /dev/ttySHSF
probeall /dev/ttySHSF hsfpcibasic2 hsfpcibasic3 hsfmc97ich hsfmc97via hsfmc97ali hsfmc97ati hsfmc97sis hsfusbcd2 snd_hda_intel snd-hda-codec-hsfmodem

Will CC: to Linuxant Support Jonathan.
 Regards,
 Antonio



----- Forwarded Message ----
From: Patrick Dupre <pd520@xxxxxxxxxx>
To: olivares14031@xxxxxxxxx
Sent: Sun, September 19, 2010 8:16:23 AM
Subject: Progress !

Hello Antonio,

I installed the driver, but it still does not work.
This is the new ModemData.txt

Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List Server,
as HTML can contain viruses. Use as the email Subject Line:
          YourName, YourCountry  kernel 2.6.34.6-47.fc13.i686.PAE
With this Subject Line cogent experts will be alerted, and useful case names left in the Archive. YourCountry will enable Country specific guidance. Linux experts in YourCountry
can be found through: http://www.linux.org/groups/index.html.
They will know your Country's modem code, which may be essential for dialup service. Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an Internet Provider mail filters.
So in a day, also check the Archived responses at http://www.linmodems.org
--------------------------  System information ----------------------------
CPU=i686,  fedora ,  ALSA_version=1.0.22
Linux version 2.6.34.6-47.fc13.i686.PAE (mockbuild@xxxxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.4.4 20100630 (Red Hat 4.4.4-10) (GCC) ) #1 SMP Fri Aug 27 09:29:49 UTC 2010
scanModem update of:  2010_05_29
The modem symbolic link is /dev/modem -> /dev/ttyS2
/etc/lsb-release not found


The dkms driver upgrade utilities are installed,

There are no blacklisted modem drivers in /etc/modprobe*  files

Potentially useful modem drivers now loaded are:
      snd_hda_intel

Attached USB devices are:
ID 413c:a005 Dell Computer Corp. Internal 2.0 Hub
If a cellphone is not detected, see http://ubuntuforums.org/archive/index.php/t-878554.html A sample report is: http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html

If a USB modem or cellphone is attached and was not detected, please
provide available information in your request to discuss@xxxxxxxxxxxxx

Candidate PCI devices with modem chips are:
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01)
High Definition Audio cards can host modem chips.

For candidate card in slot 00:1b.0, firmware information and bootup diagnostics are:
PCI slot    PCI ID        SubsystemID    Name
----------    ---------    ---------    --------------
00:1b.0 8086:27d8 1028:01cd Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller

Modem interrupt assignment and sharing:
  28:      1520          0  PCI-MSI-edge      hda_intel
--- Bootup diagnostics for card in PCI slot 00:1b.0 ----
pci 0000:00:1b.0: reg 10: [mem 0xefffc000-0xefffffff 64bit]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21
HDA Intel 0000:00:1b.0: irq 28 for MSI/MSI-X
HDA Intel 0000:00:1b.0: setting latency timer to 64
input: HDA Intel Mic at Ext Right Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7 input: HDA Intel HP Out at Ext Right Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8

The PCI slot 00:1b.0 of the modem card may be disabled early in
a bootup process,  but then enabled later. If modem drivers load
but the modem is not responsive, read DOCs/Bootup.txt about possible fixes.
Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
if help is needed.



===== Advanced Linux Sound Architecture (ALSA) diagnostics =====
The ALSA packages provide audio support and also drivers for some modems.
ALSA diagnostics are written during bootup to /proc/asound/ folders.

The modem cards detected by "aplay -l"  are: None


The /proc/asound/pcm file reports:
-----------------------
00-00: STAC92xx Analog : STAC92xx Analog : playback 1 : capture 1
00-01: STAC92xx Digital : STAC92xx Digital : playback 1

about /proc/asound/cards:
------------------------
0 [Intel          ]: HDA-Intel - HDA Intel
                      HDA Intel at 0xefffc000 irq 28

PCI slot 00:1b.0 has a High Definition Audio Card
The drivers are in the kernel modules tree at:

/lib/modules/2.6.34.6-47.fc13.i686.PAE/kernel/sound/pci/hda/snd-hda-intel.ko /lib/modules/2.6.33.8-149.fc13.i686.PAE/kernel/sound/pci/hda/snd-hda-intel.ko The modem codec file for the HDA card is: /proc/asound/card0/codec#1
--------------------------------------------------------
Codec: Conexant ID 2bfa
Address: 1
Function Id: 0x2
Vendor Id: 0x14f12bfa
Subsystem Id: 0x14f100c3
Revision Id: 0x90000
Modem Function Group: 0x2

The audio card hosts a softmodem chip:  0x14f12bfa

14f1 is the Conexant Vendor ID, and 0x14f12bfa a softmodem chipset.
Get a hsfmodem package through http://www.linuxant.com

If not a Conexant modem, the driver hsfmodem-drivers with its dependent drivers:

----------
provide audio + modem support with the modem chip residing on the subsystem.
Any particular card can host any one of several soft modem chips.

=== Finished firmware and bootup diagnostics, next deducing cogent software. ===

Predictive  diagnostics for card in bus 00:1b.0:
    Modem chipset  detected on
NAME="Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller "
CLASS=0403
PCIDEV=8086:27d8
SUBSYS=1028:01cd
IRQ=28
HDA2=00:1b.0
SOFT=8086:27d8.HDA
CodecDiagnosed=Conexant_
HDAchipVendorID=14f1
CHIP=0x14f12bfa
CodecClass=14f1
IDENT=hsfmodem
Driver=hsfmodem-drivers

For candidate modem in:  00:1b.0
0403 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller
      Primary device ID:  8086:27d8
    Subsystem PCI_id  1028:01cd
    Softmodem codec or chipset from diagnostics: Conexant_0x14f12bfa
                              from    Archives:
                        The HDA card softmodem chip is 0x14f12bfa


Support type needed or chipset:    hsfmodem


Writing DOCs/Intel.txt

For owners of a Dell PCs with Conexant HSF modems, a driver source package with full speed enabled is available, but requires driver compiling. Read DOCs/Conexant.txt


For all code packages from Linuxant.com, either a driver set matching the boot kernel will be installed, or the drivers will first be compiled and then installed. The expert on modem software for Linux is
"Support (Jonathan)" <modem.support@xxxxxxxxxxxx>

Start at  http://www.linuxant.com/drivers/hsf/full for
eventually download of a hsfmodem-7.68.00.12full_k.???.zip package
with ??? the package type (deb, rpm, tar etc)
These packages have compiled drivers but will also compile a driver,
if there is a mismatch between the resident kernel and provided driver.
The generic hsfmodem-7.68.00.12full.tar.gz package only provides compiling support


Start at http://www.linuxant.com/drivers/hsf/downloads-license.php to find the
hsfmodem package matching your System. For several Linux distros, there are
precompiled drivers matched to specific kernels. These have within the FileName,
your KernelVersion:    2.6.34.6_47.fc13.i686.PAE
They can be found through http://www.linuxant.com/drivers/hsf/full/downloads.php
A more precise location may be given a few paragraphs below.
If an EXACT Match with your your KernelVersion is not found, the needed drivers
will be auto compiled anyway. Alternatively, one of the
"Generic packages with source" near the bottom of the page must be used.
Downloaded packages must be moved into the Linux partition (home folder is OK)
and unzipped with:
    unzip hsf*.zip
The installation command for a .deb suffic packages is, with root/adm permission:
  dpkg -i hsf*.deb
while for .rpm suffix it is, with:
  rpm -i hsf*.rpm
Read DOCs/Conexant.txt

Writing DOCs/Conexant.txt


Completed candidate modem analyses.

The base of the UDEV device file system is: /dev/.udev

Versions adequately match for the compiler installed: 4.4.4
            and the compiler used in kernel assembly: 4.4.4

linux-headers-2.6.34.6-47.fc13.i686.PAE resources needed for compiling are not manifestly ready!

If compiling is necessary packages must be installed, providing:



If a driver compilation fails, with message including some lack of some FileName.h (stdio.h for example), then Some additional kernel-header files need installation to /usr/include. The minimal additional packages are libc6-dev
and any of its dependents, under Ubuntu linux-libc-dev

If an alternate ethernet connection is available,
$  apt-get update
$  apt-get -s install linux-kernel-devel
will install needed packages.
For Debian/Ubuntu related distributions, run the following command to display the needed package list:

Otherwise packages have to be found through http://packages.ubuntu.com
Once downloaded and transferred into a Linux partition,
they can be installed alltogether with:
$ sudo dpkg -i *.deb


Checking pppd properties:
    -r-xr-xr-x. 1 root root 328104 Jul 13 13:16 /usr/sbin/pppd

In case of an "error 17" "serial loopback" problem, see:
    http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html

To enable dialout without Root permission do:
    $ su - root  (not for Ubuntu)
        chmod a+x /usr/sbin/pppd
or under Ubuntu related Linuxes
    chmod a+x /usr/sbin/pppd

Checking settings of:    /etc/ppp/options
lock

In case of a message like:
  Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html

For guidance on FAX usage, get from http://linmodems.technion.ac.il/packages/ get faxing.tar.gz It has samples for a modem using port /dev/ttySL0, which must be changed to match your modem's port.

Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0 ppp0 virbr0 wlan0
Which can interfere with Browser naviagation.

Don't worry about the following, it is for experts should trouble shooting be necessary.
==========================================================

Checking for modem support lines:
--------------------------------------
/device/modem symbolic link: lrwxrwxrwx. 1 root root 10 Sep 19 14:42 /dev/modem -> /dev/ttyS2
slmodemd created symbolic link /dev/ttySL0:
    Within /etc/udev/ files:
/etc/udev/rules.d/00-hsf.rules:KERNEL=="ttySHSF0", SYMLINK="modem"
    Within /etc/modprobe.conf files:
/etc/modprobe.conf:install snd-via82xx-modem /bin/true # temporarily disabled by hsf - conflicts with hsfmc97via /etc/modprobe.conf:install snd-atiixp-modem /bin/true # temporarily disabled by hsf - conflicts with hsfmc97ati
/etc/modprobe.conf:alias /dev/modem /dev/ttySHSF
/etc/modprobe.conf:install /dev/ttySHSF /sbin/modprobe hsfpcibasic2; /sbin/modprobe hsfpcibasic3; /sbin/modprobe hsfmc97ich; /sbin/modprobe hsfmc97via; /sbin/modprobe hsfmc97ali; /sbin/modprobe hsfmc97ati; /sbin/modprobe hsfmc97sis; [ -e /lib/modules/`uname -r`/extra/hsfusbcd2.ko ] && /sbin/modprobe hsfusbcd2; /sbin/modprobe snd_hda_intel; [ -e /lib/modules/`uname -r`/extra/snd-hda-codec-hsfmodem.ko ] && /sbin/modprobe snd-hda-codec-hsfmodem; /bin/true
    Within any ancient /etc/devfs files:

    Within ancient kernel 2.4.n /etc/module.conf files:
alias /dev/modem /dev/ttySHSF
probeall /dev/ttySHSF hsfpcibasic2 hsfpcibasic3 hsfmc97ich hsfmc97via hsfmc97ali hsfmc97ati hsfmc97sis hsfusbcd2 snd_hda_intel snd-hda-codec-hsfmodem
--------- end modem support lines --------

And this is the output of wvdialconf /etc/wvdial.conf

Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

Modem Port Scan<*1>: Scanning ttyS2 first, /dev/modem is a link to it.
Modem Port Scan<*1>: S2  S0  S1  S3  SHSF0 SHSF1 SHSF2 SHSF3
Modem Port Scan<*1>: SHSF4 SHSF5 SHSF6 SHSF7

Sorry, no modem was detected!  Is it in use by another program?
Did you configure it properly with setserial?



What do you think ?

thank.

-- ---
==========================================================================
Patrick DUPRÉ                      |  |
Department of Chemistry            |  |    Phone: (44)-(0)-1904-434384
The University of York            |  |    Fax:  (44)-(0)-1904-432516
Heslington                        |  |
York YO10 5DD  United Kingdom      |  |    email: pd520@xxxxxxxxxx
==========================================================================




--
---
==========================================================================
 Patrick DUPRÃ?                      |   |
 Department of Chemistry            |   |    Phone: (44)-(0)-1904-434384
 The University of York             |   |    Fax:   (44)-(0)-1904-432516
 Heslington                         |   |
 York YO10 5DD  United Kingdom      |   |    email: pd520@xxxxxxxxxx
==========================================================================

[Index of Archives]     [Linux Media Development]     [Asterisk]     [DCCP]     [Netdev]     [X.org]     [Xfree86]     [Fedora Women]     [Linux USB]

  Powered by Linux