Kenan,
Follow the instructions provided by scanModem:
Predictive diagnostics for card in bus 00:1b.0:
Modem chipset detected on
NAME="Audio device: Intel Corporation 82801H "
CLASS=0403
PCIDEV=8086:284b
SUBSYS=1025:011f
IRQ=21
HDA=8086:284b
SOFT=8086:284b.HDA
CHIP=0x14f12c06
IDENT=hsfmodem
Driver=hsfmodem-drivers
For candidate modem in: 00:1b.0
0403 Audio device: Intel Corporation 82801H
Primary device ID: 8086:284b
Subsystem PCI_id 1025:011f
Softmodem codec or chipset from diagnostics: 0x14f12c06
from Archives:
The HDA card softmodem chip is 0x14f12c06
Support type needed or chipset: hsfmodem
Writing DOCs/Intel.txt
For owners of a Dell PCs with Conexant HSF modems, a driver source
package with full speed enabled is available, but requires driver
compiling. Read DOCs/Conexant.txt
Start at http://www.linuxant.com/drivers/hsf/downloads-license.php to find the
hsfmodem package matching your System. For several Linux distros, there are
precompiled drivers matched to specific kernels. These have within the FileName,
your KernelVersion: 2.6.31_22_generic
They can be found through
http://www.linuxant.com/drivers/hsf/full/downloads.php
A more precise location may be given a few paragraphs below.
If an EXACT Match with your your KernelVersion is not found, one of the
"Generic packages with source" near the bottom of the page must be used.
Downloaded packages must be moved into the Linux partition (home folder is OK)
and unzipped with:
unzip hsf*.zip
The installation command for a .deb suffic packages is, with root/adm
permission:
sudo dpkg -i hsf*.deb
while for .rpm suffix it is, with:
rpm -i hsf*.rpm
Support for Conexant chips hosted on High Definition Audio cards may require
installation of additional packages, one of the alsa-driver-linuxant packages
on http://www.linuxant.com/alsa-driver/ At the same time download the
alsa-driver-1.0.17-1.patch , in case it prove to be later needed. During the
hsfmodem install, there will be a message if there is necessary installation of
alsa-driver-linuxant
The installation command for a .deb suffic packages is, with root/adm
permission:
sudo alsa* -i hsf*.deb
while for .rpm suffix it is, with:
rpm -i hsf*.rpm
There may a message that "Dependencies" are not satisfied. In this
case the Ubuntu/Debian packages to be installed are linux-libc-dev &
libc6-dev. Package
names may be different for other Linuxes. If not on your install CD, these
packages can be searched for at http://packages.ubuntu.com. After download,
they can be coinstalled with:
sudo dpkg -i li*.deb
Again try the alsa-driver-linuxant
There may be a message that the patch must be applied. In this case get the
ftp://ftp.alsa-project.org/pub/driver/alsa-driver-1.0.17.tar.bz2
Under Linux, this package is unpacked with:
$ tar jxf alsa*.tar.bz2
Next the patch is applied with:
$ patch -p0 < alsa-driver-1.0.17-1.patch
See http://linmodems.technion.ac.il/bigarch/archive-eighth/msg00838.html
for details on compiling and installing replacement snd-hda-intel + its
dependent drivers.
After the installation is completed, rerun the hsfmodem installation.
Reboot and try to detect the modem with Root permission:
sudo wvdialconf /etc/wvdial.conf
From http://www.linuxant.com/drivers/hsf/full/downloads-ubuntu-x86.php
download hsfmodem-7.68.00.12full_k2.6.31_22_generic_ubuntu_i386.deb.zip
Under Linux unpack with:
$ unzip hsfmodem*.zip
Then install with:
$ sudo dpkg -i hsfmodem*.deb
Subsequently, the modem should be found with
$ sudo wvdialconf /etc/wvdial.conf
Edit in your personal information with:
$ sudo gedit /etc/wvdial.conf
and try dialing out with:
$ sudo wvdial.
See DOCs/Testing.txt for details.
Read DOCs/Conexant.txt
If the directions above do not work or the exact kernel drivers is not
found. Please follow Jonathan's instructions:
http://www.linuxant.com/drivers/hsf/install.php
Regards,
Antonio
On 7/4/10, kenan Ahmed <kenan199@xxxxxxxxx> wrote:
> Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List
> Server,
> as HTML can contain viruses. Use as the email Subject Line:
> YourName, YourCountry kernel 2.6.31-22-generic
> With this Subject Line cogent experts will be alerted, and useful
> case names left in the Archive.
> YourCountry will enable Country specific guidance. Linux experts in
> YourCountry
> can be found through: http://www.linux.org/groups/index.html.
> They will know your Country's modem code, which may be essential for
> dialup service.
> Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an
> Internet Provider mail filters.
> So in a day, also check the Archived responses at http://www.linmodems.org
> -------------------------- System information ----------------------------
> CPU=i686,
> Linux version 2.6.31-22-generic (buildd@vernadsky) (gcc version 4.4.1
> (Ubuntu 4.4.1-4ubuntu8) ) #60-Ubuntu SMP Thu May 27 00:22:23 UTC 2010
> scanModem update of: 2008_08_26
>
> There are no blacklisted modem drivers in /etc/modprobe* files
> Attached USB devices are:
> ID 1d6b:0002 Linux Foundation 2.0 root hub
> ID 1d6b:0001 Linux Foundation 1.1 root hub
> ID 1d6b:0001 Linux Foundation 1.1 root hub
> ID 1d6b:0001 Linux Foundation 1.1 root hub
> ID 5986:0102 Acer, Inc Crystal Eye Webcam
> ID 1d6b:0002 Linux Foundation 2.0 root hub
> ID 1d6b:0001 Linux Foundation 1.1 root hub
> ID 1d6b:0001 Linux Foundation 1.1 root hub
>
> USB modems not recognized
>
> For candidate card in slot 00:1b.0, firmware information and bootup
> diagnostics are:
> PCI slot PCI ID SubsystemID Name
> ---------- --------- --------- --------------
> 00:1b.0 8086:284b 1025:011f Audio device: Intel Corporation 82801H
>
> Modem interrupt assignment and sharing:
> 21: 9108 IO-APIC-fasteoi uhci_hcd:usb4, HDA Intel
> --- Bootup diagnostics for card in PCI slot 00:1b.0 ----
> [ 0.530073] pci 0000:00:1b.0: reg 10 64bit mmio: [0xfc300000-0xfc303fff]
> [ 0.530144] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
> [ 0.530149] pci 0000:00:1b.0: PME# disabled
> [ 16.975440] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 21 (level,
> low) -> IRQ 21
> [ 16.975481] HDA Intel 0000:00:1b.0: setting latency timer to 64
> [ 17.122897] input: HDA Digital PCBeep as
> /devices/pci0000:00/0000:00:1b.0/input/input8
>
> The PCI slot 00:1b.0 of the modem card may be disabled early in
> a bootup process, but then enabled later. If modem drivers load
> but the modem is not responsive, read DOCs/Bootup.txt about possible
> fixes.
> Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
> if help is needed.
>
>
>
> ===== Advanced Linux Sound Architecture (ALSA) diagnostics =====
> The ALSA packages provide audio support and also drivers for some modems.
> ALSA diagnostics are written during bootup to /proc/asound/ folders.
>
> The ALSA verion is 1.0.20
> The modem cards detected by "aplay -l" are: None
>
>
> The /proc/asound/pcm file reports:
> -----------------------
> 00-00: ALC268 Analog : ALC268 Analog : playback 1 : capture 1
> 00-02: ALC268 Analog : ALC268 Analog : capture 1
>
> about /proc/asound/cards:
> ------------------------
> 0 [Intel ]: HDA-Intel - HDA Intel
> HDA Intel at 0xfc300000 irq 21
>
> PCI slot 00:1b.0 has a High Definition Audio Card
> The drivers are in the kernel modules tree at:
> /lib/modules/2.6.31-22-generic/kernel/sound/pci/hda/snd-hda-intel.ko
> /lib/modules/2.6.31-14-generic/kernel/sound/pci/hda/snd-hda-intel.ko
> The modem codec file for the HDA card is: /proc/asound/card0/codec#1
> --------------------------------------------------------
> Codec: Conexant ID 2c06
> Address: 1
> Function Id: 0x2
> Vendor Id: 0x14f12c06
> Subsystem Id: 0x10250093
> Revision Id: 0x100000
> Modem Function Group: 0x2
>
> The audio card hosts a softmodem chip: 0x14f12c06
>
> 14f1 is the Conexant Vendor ID, and 0x14f12c06 a softmodem chipset.
> Get a hsfmodem package through http://www.linuxant.com
>
> If not a Conexant modem, the driver hsfmodem-drivers with its dependent
> drivers:
>
> ----------
> provide audio + modem support with the modem chip residing on the subsystem.
> Any particular card can host any one of several soft modem chips.
>
> === Finished firmware and bootup diagnostics, next deducing cogent software.
> ===
>
> Predictive diagnostics for card in bus 00:1b.0:
> Modem chipset detected on
> NAME="Audio device: Intel Corporation 82801H "
> CLASS=0403
> PCIDEV=8086:284b
> SUBSYS=1025:011f
> IRQ=21
> HDA=8086:284b
> SOFT=8086:284b.HDA
> CHIP=0x14f12c06
> IDENT=hsfmodem
> Driver=hsfmodem-drivers
>
> For candidate modem in: 00:1b.0
> 0403 Audio device: Intel Corporation 82801H
> Primary device ID: 8086:284b
> Subsystem PCI_id 1025:011f
> Softmodem codec or chipset from diagnostics: 0x14f12c06
> from Archives:
> The HDA card softmodem chip is 0x14f12c06
>
>
> Support type needed or chipset: hsfmodem
>
>
> Writing DOCs/Intel.txt
>
> For owners of a Dell PCs with Conexant HSF modems, a driver source
> package with full speed enabled is available, but requires driver
> compiling. Read DOCs/Conexant.txt
>
>
> Start at http://www.linuxant.com/drivers/hsf/downloads-license.php to find
> the
> hsfmodem package matching your System. For several Linux distros, there are
> precompiled drivers matched to specific kernels. These have within the
> FileName,
> your KernelVersion: 2.6.31_22_generic
> They can be found through
> http://www.linuxant.com/drivers/hsf/full/downloads.php
> A more precise location may be given a few paragraphs below.
> If an EXACT Match with your your KernelVersion is not found, one of the
> "Generic packages with source" near the bottom of the page must be used.
> Downloaded packages must be moved into the Linux partition (home folder is
> OK)
> and unzipped with:
> unzip hsf*.zip
> The installation command for a .deb suffic packages is, with root/adm
> permission:
> sudo dpkg -i hsf*.deb
> while for .rpm suffix it is, with:
> rpm -i hsf*.rpm
>
> Support for Conexant chips hosted on High Definition Audio cards may require
> installation of additional packages, one of the alsa-driver-linuxant
> packages
> on http://www.linuxant.com/alsa-driver/ At the same time download the
> alsa-driver-1.0.17-1.patch , in case it prove to be later needed. During the
> hsfmodem install, there will be a message if there is necessary installation
> of
> alsa-driver-linuxant
>
> The installation command for a .deb suffic packages is, with root/adm
> permission:
> sudo alsa* -i hsf*.deb
> while for .rpm suffix it is, with:
> rpm -i hsf*.rpm
>
> There may a message that "Dependencies" are not satisfied. In this
> case the Ubuntu/Debian packages to be installed are linux-libc-dev &
> libc6-dev. Package
> names may be different for other Linuxes. If not on your install CD, these
> packages can be searched for at http://packages.ubuntu.com. After download,
> they can be coinstalled with:
> sudo dpkg -i li*.deb
> Again try the alsa-driver-linuxant
>
> There may be a message that the patch must be applied. In this case get the
> ftp://ftp.alsa-project.org/pub/driver/alsa-driver-1.0.17.tar.bz2
> Under Linux, this package is unpacked with:
> $ tar jxf alsa*.tar.bz2
> Next the patch is applied with:
> $ patch -p0 < alsa-driver-1.0.17-1.patch
>
> See http://linmodems.technion.ac.il/bigarch/archive-eighth/msg00838.html
> for details on compiling and installing replacement snd-hda-intel + its
> dependent drivers.
> After the installation is completed, rerun the hsfmodem installation.
> Reboot and try to detect the modem with Root permission:
> sudo wvdialconf /etc/wvdial.conf
>
> From http://www.linuxant.com/drivers/hsf/full/downloads-ubuntu-x86.php
> download hsfmodem-7.68.00.12full_k2.6.31_22_generic_ubuntu_i386.deb.zip
> Under Linux unpack with:
> $ unzip hsfmodem*.zip
> Then install with:
> $ sudo dpkg -i hsfmodem*.deb
> Subsequently, the modem should be found with
> $ sudo wvdialconf /etc/wvdial.conf
> Edit in your personal information with:
> $ sudo gedit /etc/wvdial.conf
> and try dialing out with:
> $ sudo wvdial.
> See DOCs/Testing.txt for details.
>
> Read DOCs/Conexant.txt
>
> Writing DOCs/Conexant.txt
>
>
> Completed candidate modem analyses.
>
> The base of the UDEV device file system is: /dev/.udev
>
> Versions adequately match for the compiler installed: 4.4.1
> and the compiler used in kernel assembly: 4.4.1
>
>
>
> Minimal compiling resources appear complete:
> make utility - /usr/bin/make
> Compiler version 4.4
> linuc_headers base folder /lib/modules/2.6.31-22-generic/build
>
> However some compilations and executable functions may need additional
> files,
> in the FileNames.h (so called kernel "h"eaders) collection installed
> in /usr/include/ .
> For martian_modem, additional required packages are needed. The also
> required headers of package libc6 are commonly installed by default.
> Compiling hsfmodem drivers does require linux-libc-dev and libc6-dev
> packages, for kernels 2.6.24 and later versions.
> In not included on your install CD, search for them at
> http://packages.ubuntu.com
> or comparable Repository for other Linux distros.
> When compiling ALSA drivers, the utility "patch" will also be needed.
>
>
>
>
> If a driver compilation fails, with message including some lack of
> some FileName.h (stdio.h for example), then
> Some additional kernel-header files need installation to /usr/include.
> The minimal additional packages are libc6-dev
> and any of its dependents, under Ubuntu linux-libc-dev
>
> If an alternate ethernet connection is available,
> $ apt-get update
> $ apt-get -s install linux-kernel-devel
> will install needed packages.
> For Debian/Ubuntu related distributions, run the following command to
> display the needed package list:
>
> Otherwise packages have to be found through http://packages.ubuntu.com
> Once downloaded and transferred into a Linux partition,
> they can be installed alltogether with:
> $ sudo dpkg -i *.deb
>
> Checking settings of: /etc/ppp/options
> asyncmap 0
> noauth
> crtscts
> lock
> hide-password
> modem
> proxyarp
> lcp-echo-interval 30
> lcp-echo-failure 4
> noipx
>
> In case of a message like:
> Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
> see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
>
> Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0
> Which can interfere with Browser naviagation.
>
> Don't worry about the following, it is for experts should trouble
> shooting be necessary.
> ==========================================================
>
> Checking for modem support lines:
> --------------------------------------
> /device/modem symbolic link:
> slmodemd created symbolic link /dev/ttySL0:
> Within /etc/udev/ files:
>
> Within /etc/modprobe.conf files:
> /etc/modprobe.d/alsa-base.conf:options snd-atiixp-modem index=-2
> /etc/modprobe.d/alsa-base.conf:options snd-via82xx-modem index=-2
> /etc/modprobe.d/blacklist-modem.conf:# Uncomment these entries in
> order to blacklist unwanted modem drivers
> /etc/modprobe.d/blacklist-modem.conf:# blacklist snd-atiixp-modem
> /etc/modprobe.d/blacklist-modem.conf:# blacklist snd-via82xx-modem
> Within any ancient /etc/devfs files:
>
> Within ancient kernel 2.4.n /etc/module.conf files:
>
> --------- end modem support lines --------
>
