Taras,
scanModem reports that your modem is supported through hsfmodem
drivers available at linuxant:
Predictive diagnostics for card in bus 00:1b.0:
Modem chipset detected on
NAME="Audio device: Intel Corporation 82801H "
CLASS=0403
PCIDEV=8086:284b
SUBSYS=152d:0769
IRQ=22
HDA2=00:1b.0
SOFT=8086:284b.HDA
IDENT=hsfmodem
Driver=hsfmodem-drivers
For candidate modem in: 00:1b.0
0403 Audio device: Intel Corporation 82801H
Primary device ID: 8086:284b
Subsystem PCI_id 152d:0769
Softmodem codec or chipset from diagnostics:
from Archives:
Support type needed or chipset: hsfmodem
Writing DOCs/Intel.txt
For owners of a Dell PCs with Conexant HSF modems, a driver source
package with full speed enabled is available, but requires driver
compiling. Read DOCs/Conexant.txt
From http://www.linuxant.com/drivers/hsf/full/downloads-ubuntu-x86.php
download hsfmodem-7.80.02.05full_k2.6.31_20_generic_ubuntu_i386.deb.zip
Under Linux unpack with:
$ unzip hsfmodem*.zip
Then install with:
$ sudo dpkg -i hsfmodem*.deb
Subsequently, the modem should be found with
$ sudo wvdialconf /etc/wvdial.conf
Edit in your personal information with:
$ sudo gedit /etc/wvdial.conf
and try dialing out with:
$ sudo wvdial.
See DOCs/Testing.txt for details
scanModem also reports that you do not have wvdial installed and how
to install it:
Distrib_ID=Ubuntu
DistribCodeName=karmic
AptRepositoryStem=http://archive.ubuntu.com/ubuntu/
The dialer utility package WVDIAL does not appear to be installed on
your System.
For Ubuntu users, there are at the bottom of
http://linmodems.technion.ac.il/packages/
packages with the files necessary to install wvdial, with names like:
wvdial_jaunty_amd64.zip for x86_64, 64 bit bus systems.
wvdial_jaunty_i386.zip for 32 bit systems.
wvdial_karmic_i386.zip for 32 bit systems.
These are about 1 MB in size. After downloaded and copied into your
Linux partition:
$ unzip wv*.zip
Within the new folder:
$ sudo dpkg -i *.deb
will complete the wvdial installation
Please read Modem/DOCs/wvdial.txt for usage information.
Should you install the driver correctly, and it does not respond it
could be because of, but only should the need arise. scanModem gives
you the following:
For candidate card in slot 00:1b.0, firmware information and bootup
diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
00:1b.0 8086:284b 152d:0769 Audio device: Intel
Corporation 82801H
Modem interrupt assignment and sharing:
22: 33536 29443 IO-APIC-fasteoi HDA Intel
--- Bootup diagnostics for card in PCI slot 00:1b.0 ----
[ 1.357488] pci 0000:00:1b.0: reg 10 64bit mmio: [0xf0400000-0xf0403fff]
[ 1.357592] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 1.357603] pci 0000:00:1b.0: PME# disabled
[ 8.979424] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level,
low) -> IRQ 22
[ 8.979465] HDA Intel 0000:00:1b.0: setting latency timer to 64
The PCI slot 00:1b.0 of the modem card may be disabled early in
a bootup process, but then enabled later. If modem drivers load
but the modem is not responsive, read DOCs/Bootup.txt about possible fixes.
Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
if help is needed.
Regards,
Antonio
On 2/24/10, Taras Tsaryuk <taras.tsaryuk@xxxxxxxxx> wrote:
>
>
