Hi, I have been using Linux for about a year now and can do basic things on it but getting a bit overwhelmed on installing the modem so would like help. Yesterday I installed the hfs for my system following from modemdata.txt and since then each time my laptop tries to suspend or hibernate it freezes and the only thing that brings it out of that is Ctrl-SysRq-B (does not seem to do anything on R, E, I, S, U but I do hit those before and give them some time anyway). Below is what I did get done. Start at http://www.linuxant.com/drivers/hsf/downloads-license.php to find the hsfmodem package matching your System. For several Linux distros, there are precompiled drivers matched to specific kernels. These have within the FileName, your KernelVersion: 2.6.31_19_generic They can be found through http://www.linuxant.com/drivers/hsf/full/downloads.php A more precise location may be given a few paragraphs below. If an EXACT Match with your your KernelVersion is not found, one of the "Generic packages with source" near the bottom of the page must be used. Downloaded packages must be moved into the Linux partition (home folder is OK) and unzipped with: unzip hsf*.zip The installation command for a .deb suffic packages is, with root/adm permission: sudo dpkg -i hsf*.deb while for .rpm suffix it is, with: rpm -i hsf*.rpm Since then I installed wvdial but on sudo wvdialconf wvtest it says Scanning your serial ports for a modem. Modem Port Scan<*1>: Scanning ttySHSF0 first, /dev/modem is a link to it. Modem Port Scan<*1>: SHSF0 S0 S1 S2 S3 SHSF1 SHSF2 SHSF3 Modem Port Scan<*1>: SHSF4 SHSF5 SHSF6 SHSF7 Sorry, no modem was detected! Is it in use by another program? Did you configure it properly with setserial? Please read the FAQ at http://open.nit.ca/wiki/?WvDial If you still have problems, send mail to <wvdial-list@xxxxxxxxxxxx>. At this point I would just like some expert help. Below is the text of ModemData.txt, the full text, and after that dmesg.txt follows. Best, Peter Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List Server, as HTML can contain viruses. Use as the email Subject Line: YourName, YourCountry kernel 2.6.31-19-generic With this Subject Line cogent experts will be alerted, and useful case names left in the Archive. YourCountry will enable Country specific guidance. Linux experts in YourCountry can be found through: http://www.linux.org/groups/index.html. They will know your Country's modem code, which may be essential for dialup service. Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an Internet Provider mail filters. So in a day, also check the Archived responses at http://www.linmodems.org -------------------------- System information ---------------------------- CPU=i686, Ubuntu , ALSA_version=1.0.20 Linux version 2.6.31-19-generic (buildd@palmer) (gcc version 4.4.1 (Ubuntu 4.4.1-4ubuntu8) ) #56-Ubuntu SMP Thu Jan 28 01:26:53 UTC 2010 scanModem update of: 2010_02_04 The modem symbolic link is /dev/modem -> ttySHSF0 The dkms driver upgrade utilities are installed, There are no blacklisted modem drivers in /etc/modprobe* files Potentially useful modem drivers now loaded are: Attached USB devices are: ID 0fca:8004 Research In Motion, Ltd. ID 0781:a3a4 SanDisk Corp. If a cellphone is not detected, see http://ubuntuforums.org/archive/index.php/t-878554.html A sample report is: http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html If a USB modem or cellphone is attached and was not detected, please provide available information in your request to discuss@xxxxxxxxxxxxx Candidate PCI devices with modem chips are: 00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 04) High Definition Audio cards can host modem chips. For candidate card in slot 00:1e.3, firmware information and bootup diagnostics are: PCI slot PCI ID SubsystemID Name ---------- --------- --------- -------------- 00:1e.3 8086:266d 1179:ff31 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW Modem interrupt assignment and sharing: --- Bootup diagnostics for card in PCI slot 00:1e.3 ---- [ 0.416716] pci 0000:00:1e.3: reg 10 io port: [0x2400-0x24ff] [ 0.416724] pci 0000:00:1e.3: reg 14 io port: [0x2000-0x207f] [ 0.416773] pci 0000:00:1e.3: PME# supported from D0 D3hot D3cold [ 0.416778] pci 0000:00:1e.3: PME# disabled [ 1.276017] serial 0000:00:1e.3: PCI INT B -> GSI 20 (level, low) -> IRQ 20 [ 1.276025] serial 0000:00:1e.3: PCI INT B disabled [ 1232.264588] hsfich 0000:00:1e.3: PCI INT B -> GSI 20 (level, low) -> IRQ 20 The PCI slot 00:1e.3 of the modem card may be disabled early in a bootup process, but then enabled later. If modem drivers load but the modem is not responsive, read DOCs/Bootup.txt about possible fixes. Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx if help is needed. ===== Advanced Linux Sound Architecture (ALSA) diagnostics ===== The ALSA packages provide audio support and also drivers for some modems. ALSA diagnostics are written during bootup to /proc/asound/ folders. The modem cards detected by "aplay -l" are: None The /proc/asound/pcm file reports: ----------------------- 00-00: Intel ICH : Intel ICH6 : playback 1 : capture 1 00-01: Intel ICH - MIC ADC : Intel ICH6 - MIC ADC : capture 1 00-02: Intel ICH - MIC2 ADC : Intel ICH6 - MIC2 ADC : capture 1 00-03: Intel ICH - ADC2 : Intel ICH6 - ADC2 : capture 1 00-04: Intel ICH - IEC958 : Intel ICH6 - IEC958 : playback 1 about /proc/asound/cards: ------------------------ 0 [ICH6 ]: ICH4 - Intel ICH6 Intel ICH6 with Cx20468-31 at irq 17 === Finished firmware and bootup diagnostics, next deducing cogent software. === Predictive diagnostics for card in bus 00:1e.3: Modem chipset not detected on NAME="Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW " CLASS=0703 PCIDEV=8086:266d SUBSYS=1179:ff31 IRQ=20 SOFT=8086:266d.MC97 CodecArchived=CXT CodecClass=CXT IDENT=hsfmodem Driver=hsfmodem-drivers For candidate modem in: 00:1e.3 Primary device ID: Support type needed or chipset: Completed candidate modem analyses. The base of the UDEV device file system is: /dev/.udev Versions adequately match for the compiler installed: 4.4.1 and the compiler used in kernel assembly: 4.4.1 Minimal compiling resources appear complete: make utility - /usr/bin/make Compiler version 4.4 linuc_headers base folder /lib/modules/2.6.31-19-generic/build However some compilations and executable functions may need additional files, in the FileNames.h (so called kernel "h"eaders) collection installed in /usr/include/ . For martian_modem, additional required packages are needed. The also required headers of package libc6 are commonly installed by default. Compiling hsfmodem drivers does require linux-libc-dev and libc6-dev packages, for kernels 2.6.24 and later versions. In not included on your install CD, search for them at http://packages.ubuntu.com or comparable Repository for other Linux distros. When compiling ALSA drivers, the utility "patch" will also be needed. If a driver compilation fails, with message including some lack of some FileName.h (stdio.h for example), then Some additional kernel-header files need installation to /usr/include. The minimal additional packages are libc6-dev and any of its dependents, under Ubuntu linux-libc-dev If an alternate ethernet connection is available, $ apt-get update $ apt-get -s install linux-kernel-devel will install needed packages. For Debian/Ubuntu related distributions, run the following command to display the needed package list: Otherwise packages have to be found through http://packages.ubuntu.com Once downloaded and transferred into a Linux partition, they can be installed alltogether with: $ sudo dpkg -i *.deb Checking pppd properties: -rwsr-xr-x 1 root dip 277352 2009-02-20 17:25 /usr/sbin/pppd In case of an "error 17" "serial loopback" problem, see: http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html To enable dialout without Root permission do: $ su - root (not for Ubuntu) sudo chmod a+x /usr/sbin/pppd or under Ubuntu related Linuxes sudo chmod a+x /usr/sbin/pppd Checking settings of: /etc/ppp/options asyncmap 0 noauth crtscts lock hide-password modem proxyarp lcp-echo-interval 30 lcp-echo-failure 4 noipx In case of a message like: Warning: Could not modify /etc/ppp/pap-secrets: Permission denied see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html For guidance on FAX usage, get from http://linmodems.technion.ac.il/packages/ get faxing.tar.gz It has samples for a modem using port /dev/ttySL0, which must be changed to match your modem's port. Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0 eth1 Which can interfere with Browser naviagation. Don't worry about the following, it is for experts should trouble shooting be necessary. ========================================================== Checking for modem support lines: -------------------------------------- /device/modem symbolic link: lrwxrwxrwx 1 root root 8 2010-02-09 09:32 /dev/modem -> ttySHSF0 slmodemd created symbolic link /dev/ttySL0: Within /etc/udev/ files: /etc/udev/rules.d/00-hsf.rules:KERNEL=="ttySHSF0", SYMLINK="modem" Within /etc/modprobe.conf files: /etc/modprobe.d/hsf.conf:alias /dev/modem /dev/ttySHSF /etc/modprobe.d/hsf.conf:install /dev/ttySHSF /sbin/modprobe hsfpcibasic2; /sbin/modprobe hsfpcibasic3; /sbin/modprobe hsfmc97ich; /sbin/modprobe hsfmc97via; /sbin/modprobe hsfmc97ali; /sbin/modprobe hsfmc97ati; /sbin/modprobe hsfmc97sis; [ -e /lib/modules/`uname -r`/extra/hsfusbcd2.ko ] && /sbin/modprobe hsfusbcd2; /sbin/modprobe snd_hda_intel; [ -e /lib/modules/`uname -r`/extra/snd-hda-codec-hsfmodem.ko ] && /sbin/modprobe snd-hda-codec-hsfmodem; /bin/true /etc/modprobe.d/hsf.conflicts.conf:install snd-via82xx-modem /bin/true # temporarily disabled by hsf - conflicts with hsfmc97via /etc/modprobe.d/hsf.conflicts.conf:install snd-atiixp-modem /bin/true # temporarily disabled by hsf - conflicts with hsfmc97ati /etc/modprobe.d/alsa-base.conf:options snd-atiixp-modem index=-2 /etc/modprobe.d/alsa-base.conf:options snd-via82xx-modem index=-2 /etc/modprobe.d/blacklist-modem.conf:# Uncomment these entries in order to blacklist unwanted modem drivers /etc/modprobe.d/blacklist-modem.conf:# blacklist snd-atiixp-modem /etc/modprobe.d/blacklist-modem.conf:# blacklist snd-via82xx-modem Within any ancient /etc/devfs files: Within ancient kernel 2.4.n /etc/module.conf files: /etc/modules.conf:alias /dev/modem /dev/ttySHSF /etc/modules.conf:probeall /dev/ttySHSF hsfpcibasic2 hsfpcibasic3 hsfmc97ich hsfmc97via hsfmc97ali hsfmc97ati hsfmc97sis hsfusbcd2 snd_hda_intel snd-hda-codec-hsfmodem --------- end modem support lines -------- CPU0 0: 372938 IO-APIC-edge timer 1: 4656 IO-APIC-edge i8042 8: 1 IO-APIC-edge rtc0 9: 18134 IO-APIC-fasteoi acpi 12: 453405 IO-APIC-edge i8042 14: 68417 IO-APIC-edge ata_piix 15: 71572 IO-APIC-edge ata_piix 16: 78199 IO-APIC-fasteoi i915, yenta 17: 417 IO-APIC-fasteoi ipw2200, Intel ICH6 19: 23205 IO-APIC-fasteoi uhci_hcd:usb3, eth0 23: 147972 IO-APIC-fasteoi ehci_hcd:usb1, uhci_hcd:usb2 NMI: 0 Non-maskable interrupts LOC: 195704 Local timer interrupts SPU: 0 Spurious interrupts CNT: 0 Performance counter interrupts PND: 0 Performance pending work RES: 0 Rescheduling interrupts CAL: 0 Function call interrupts TLB: 0 TLB shootdowns TRM: 0 Thermal event interrupts THR: 0 Threshold APIC interrupts MCE: 0 Machine check exceptions MCP: 23 Machine check polls ERR: 0 MIS: 0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.31-19-generic (buildd@palmer) (gcc version 4.4.1 (Ubuntu 4.4.1-4ubuntu8) ) #56-Ubuntu SMP Thu Jan 28 01:26:53 UTC 2010 (Ubuntu 2.6.31-19.56-generic) [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] NSC Geode by NSC [ 0.000000] Cyrix CyrixInstead [ 0.000000] Centaur CentaurHauls [ 0.000000] Transmeta GenuineTMx86 [ 0.000000] Transmeta TransmetaCPU [ 0.000000] UMC UMC UMC UMC [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e0000 - 00000000000e4000 (reserved) [ 0.000000] BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000005f670000 (usable) [ 0.000000] BIOS-e820: 000000005f670000 - 000000005f684000 (ACPI data) [ 0.000000] BIOS-e820: 000000005f684000 - 000000005f700000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000005f700000 - 0000000060000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0006000 (reserved) [ 0.000000] BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved) [ 0.000000] BIOS-e820: 00000000fed20000 - 00000000fed90000 (reserved) [ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved) [ 0.000000] DMI present. [ 0.000000] last_pfn = 0x5f670 max_arch_pfn = 0x100000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-BFFFF uncachable [ 0.000000] C0000-CFFFF write-protect [ 0.000000] D0000-E3FFF uncachable [ 0.000000] E4000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask FC0000000 write-back [ 0.000000] 1 base 040000000 mask FE0000000 write-back [ 0.000000] 2 base 05F700000 mask FFFF00000 uncachable [ 0.000000] 3 base 05F800000 mask FFF800000 uncachable [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] PAT not supported by CPU. [ 0.000000] e820 update range: 0000000000002000 - 0000000000006000 (usable) ==> (reserved) [ 0.000000] Scanning 1 areas for low memory corruption [ 0.000000] modified physical RAM map: [ 0.000000] modified: 0000000000000000 - 0000000000002000 (usable) [ 0.000000] modified: 0000000000002000 - 0000000000006000 (reserved) [ 0.000000] modified: 0000000000006000 - 000000000009f800 (usable) [ 0.000000] modified: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] modified: 00000000000e0000 - 00000000000e4000 (reserved) [ 0.000000] modified: 00000000000e8000 - 0000000000100000 (reserved) [ 0.000000] modified: 0000000000100000 - 000000005f670000 (usable) [ 0.000000] modified: 000000005f670000 - 000000005f684000 (ACPI data) [ 0.000000] modified: 000000005f684000 - 000000005f700000 (ACPI NVS) [ 0.000000] modified: 000000005f700000 - 0000000060000000 (reserved) [ 0.000000] modified: 00000000e0000000 - 00000000f0006000 (reserved) [ 0.000000] modified: 00000000f0008000 - 00000000f000c000 (reserved) [ 0.000000] modified: 00000000fed20000 - 00000000fed90000 (reserved) [ 0.000000] modified: 00000000ff000000 - 0000000100000000 (reserved) [ 0.000000] initial memory mapped : 0 - 00c00000 [ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000 [ 0.000000] Using x86 segment limits to approximate NX protection [ 0.000000] 0000000000 - 0000400000 page 4k [ 0.000000] 0000400000 - 0037400000 page 2M [ 0.000000] 0037400000 - 00377fe000 page 4k [ 0.000000] kernel direct mapping tables up to 377fe000 @ 7000-c000 [ 0.000000] RAMDISK: 3779d000 - 37fef3b9 [ 0.000000] Allocated new RAMDISK: 008ad000 - 010ff3b9 [ 0.000000] Move RAMDISK from 000000003779d000 - 0000000037fef3b8 to 008ad000 - 010ff3b8 [ 0.000000] ACPI: RSDP 000f6c40 00014 (v00 TOSQCI) [ 0.000000] ACPI: RSDT 5f67efb9 00044 (v01 TOSQCI RSDT 06040000 LTP 00000000) [ 0.000000] ACPI: FACP 5f683e8a 00074 (v01 TOSQCI ALVISO 06040000 LOHR 0000005F) [ 0.000000] ACPI: DSDT 5f67f833 04657 (v01 TOSQCI ALVISO 06040000 MSFT 0100000E) [ 0.000000] ACPI: FACS 5f694fc0 00040 [ 0.000000] ACPI: APIC 5f683efe 00066 (v01 TOSQCI ALVISO 06040000 LOHR 0000005F) [ 0.000000] ACPI: HPET 5f683f64 00038 (v01 TOSQCI ALVISO 06040000 LOHR 0000005F) [ 0.000000] ACPI: MCFG 5f683f9c 0003C (v01 TOSQCI ALVISO 06040000 LOHR 0000005F) [ 0.000000] ACPI: BOOT 5f683fd8 00028 (v01 PTLTD $SBFTBL$ 06040000 LTP 00000001) [ 0.000000] ACPI: SSDT 5f67f3ee 00235 (v01 PmRef Cpu0Ist 00003000 INTL 20030224) [ 0.000000] ACPI: SSDT 5f67f216 001D8 (v01 PmRef Cpu0Cst 00003001 INTL 20030224) [ 0.000000] ACPI: SSDT 5f67effd 00219 (v01 PmRef CpuPm 00003000 INTL 20030224) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] 638MB HIGHMEM available. [ 0.000000] 887MB LOWMEM available. [ 0.000000] mapped low ram: 0 - 377fe000 [ 0.000000] low ram: 0 - 377fe000 [ 0.000000] node 0 low ram: 00000000 - 377fe000 [ 0.000000] node 0 bootmap 00008000 - 0000ef00 [ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 00377fe000] [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] [ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] [ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] [ 0.000000] #3 [0000100000 - 00008a80a0] TEXT DATA BSS ==> [0000100000 - 00008a80a0] [ 0.000000] #4 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000] [ 0.000000] #5 [00008a9000 - 00008ac15c] BRK ==> [00008a9000 - 00008ac15c] [ 0.000000] #6 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000] [ 0.000000] #7 [00008ad000 - 00010ff3b9] NEW RAMDISK ==> [00008ad000 - 00010ff3b9] [ 0.000000] #8 [0000008000 - 000000f000] BOOTMAP ==> [0000008000 - 000000f000] [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000000 -> 0x00001000 [ 0.000000] Normal 0x00001000 -> 0x000377fe [ 0.000000] HighMem 0x000377fe -> 0x0005f670 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[3] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00000002 [ 0.000000] 0: 0x00000006 -> 0x0000009f [ 0.000000] 0: 0x00000100 -> 0x0005f670 [ 0.000000] On node 0 totalpages: 390667 [ 0.000000] free_area_init_node: node 0, pgdat c0784960, node_mem_map c1100000 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 3963 pages, LIFO batch:0 [ 0.000000] Normal zone: 1744 pages used for memmap [ 0.000000] Normal zone: 221486 pages, LIFO batch:31 [ 0.000000] HighMem zone: 1277 pages used for memmap [ 0.000000] HighMem zone: 162165 pages, LIFO batch:31 [ 0.000000] Using APIC driver default [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec20000] gsi_base[24]) [ 0.000000] IOAPIC[1]: apic_id 2, version 255, address 0xfec20000, GSI 24-279 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 2 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0x0 is invalid [ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs [ 0.000000] nr_irqs_gsi: 280 [ 0.000000] PM: Registered nosave memory: 0000000000002000 - 0000000000006000 [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 00000000000e4000 [ 0.000000] PM: Registered nosave memory: 00000000000e4000 - 00000000000e8000 [ 0.000000] PM: Registered nosave memory: 00000000000e8000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 60000000 (gap: 60000000:80000000) [ 0.000000] NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:1 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 14 pages at c1cf7000, static data 35612 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 387614 [ 0.000000] Kernel command line: BOOT_IMAGE=/vmlinuz-2.6.31-19-generic root=/dev/mapper/PBubuntu-root ro quiet splash [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] allocated 7815360 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Initializing HighMem for node 0 (000377fe:0005f670) [ 0.000000] Memory: 1524732k/1563072k available (4567k kernel code, 37148k reserved, 2141k data, 540k init, 653768k highmem) [ 0.000000] virtual kernel memory layout: [ 0.000000] fixmap : 0xfff1d000 - 0xfffff000 ( 904 kB) [ 0.000000] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 0.000000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB) [ 0.000000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB) [ 0.000000] .init : 0xc078e000 - 0xc0815000 ( 540 kB) [ 0.000000] .data : 0xc0575c48 - 0xc078d408 (2141 kB) [ 0.000000] .text : 0xc0100000 - 0xc0575c48 (4567 kB) [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.000000] SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:2304 nr_irqs:256 [ 0.000000] Fast TSC calibration using PIT [ 0.000000] Detected 1729.759 MHz processor. [ 0.001701] Console: colour VGA+ 80x25 [ 0.001706] console [tty0] enabled [ 0.004012] Calibrating delay loop (skipped), value calculated using timer frequency.. 3459.51 BogoMIPS (lpj=6919036) [ 0.004041] Security Framework initialized [ 0.004074] AppArmor: AppArmor initialized [ 0.004083] Mount-cache hash table entries: 512 [ 0.004255] Initializing cgroup subsys ns [ 0.004261] Initializing cgroup subsys cpuacct [ 0.004266] Initializing cgroup subsys memory [ 0.004277] Initializing cgroup subsys freezer [ 0.004280] Initializing cgroup subsys net_cls [ 0.004301] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.004305] CPU: L2 cache: 2048K [ 0.004311] mce: CPU supports 5 MCE banks [ 0.004321] CPU0: Thermal monitoring enabled (TM1) [ 0.004334] Performance Counters: p6 PMU driver. [ 0.004343] ... version: 0 [ 0.004345] ... bit width: 32 [ 0.004347] ... generic counters: 2 [ 0.004349] ... value mask: 00000000ffffffff [ 0.004352] ... max period: 000000007fffffff [ 0.004354] ... fixed-purpose counters: 0 [ 0.004356] ... counter mask: 0000000000000003 [ 0.004361] Checking 'hlt' instruction... OK. [ 0.020896] SMP alternatives: switching to UP code [ 0.027906] Freeing SMP alternatives: 19k freed [ 0.027915] ACPI: Core revision 20090521 [ 0.041133] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.080837] CPU0: Intel(R) Pentium(R) M processor 1.73GHz stepping 08 [ 0.084001] Brought up 1 CPUs [ 0.084001] Total of 1 processors activated (3459.51 BogoMIPS). [ 0.084001] CPU0 attaching NULL sched-domain. [ 0.084001] Booting paravirtualized kernel on bare hardware [ 0.084001] regulator: core version 0.5 [ 0.084001] Time: 9:12:13 Date: 02/09/10 [ 0.084001] NET: Registered protocol family 16 [ 0.084001] EISA bus registered [ 0.084001] ACPI: bus type pci registered [ 0.084001] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 [ 0.084001] PCI: MCFG area at e0000000 reserved in E820 [ 0.084001] PCI: Using MMCONFIG for extended config space [ 0.084001] PCI: Using configuration type 1 for base access [ 0.084001] bio: create slab <bio-0> at 0 [ 0.084001] ACPI: EC: Look up EC in DSDT [ 0.085455] ACPI: EC: non-query interrupt received, switching to interrupt mode [ 0.092021] ACPI: EC: GPE storm detected, transactions will use polling mode [ 0.412062] ACPI: Interpreter enabled [ 0.412071] ACPI: (supports S0 S3 S4 S5) [ 0.412094] ACPI: Using IOAPIC for interrupt routing [ 0.415030] ACPI: EC: GPE = 0x1d, I/O: command/status = 0x66, data = 0x62 [ 0.415033] ACPI: EC: driver started in poll mode [ 0.415252] ACPI: No dock devices found. [ 0.415784] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.415871] pci 0000:00:02.0: reg 10 32bit mmio: [0xb0080000-0xb00fffff] [ 0.415877] pci 0000:00:02.0: reg 14 io port: [0x1800-0x1807] [ 0.415882] pci 0000:00:02.0: reg 18 32bit mmio: [0xc0000000-0xcfffffff] [ 0.415888] pci 0000:00:02.0: reg 1c 32bit mmio: [0xb0000000-0xb003ffff] [ 0.415920] pci 0000:00:02.1: reg 10 32bit mmio: [0x000000-0x07ffff] [ 0.416064] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.416069] pci 0000:00:1c.0: PME# disabled [ 0.416153] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold [ 0.416158] pci 0000:00:1c.1: PME# disabled [ 0.416242] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold [ 0.416247] pci 0000:00:1c.2: PME# disabled [ 0.416312] pci 0000:00:1d.0: reg 20 io port: [0x1820-0x183f] [ 0.416374] pci 0000:00:1d.1: reg 20 io port: [0x1840-0x185f] [ 0.416441] pci 0000:00:1d.7: reg 10 32bit mmio: [0xb0040000-0xb00403ff] [ 0.416501] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 0.416507] pci 0000:00:1d.7: PME# disabled [ 0.416610] pci 0000:00:1e.2: reg 10 io port: [0x1c00-0x1cff] [ 0.416618] pci 0000:00:1e.2: reg 14 io port: [0x18c0-0x18ff] [ 0.416627] pci 0000:00:1e.2: reg 18 32bit mmio: [0xb0040800-0xb00409ff] [ 0.416635] pci 0000:00:1e.2: reg 1c 32bit mmio: [0xb0040400-0xb00404ff] [ 0.416673] pci 0000:00:1e.2: PME# supported from D0 D3hot D3cold [ 0.416678] pci 0000:00:1e.2: PME# disabled [ 0.416716] pci 0000:00:1e.3: reg 10 io port: [0x2400-0x24ff] [ 0.416724] pci 0000:00:1e.3: reg 14 io port: [0x2000-0x207f] [ 0.416773] pci 0000:00:1e.3: PME# supported from D0 D3hot D3cold [ 0.416778] pci 0000:00:1e.3: PME# disabled [ 0.416867] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 [ 0.416874] pci 0000:00:1f.0: quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO [ 0.416879] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO [ 0.416884] pci 0000:00:1f.0: LPC Generic IO decode 1 PIO at 1600-167f [ 0.416889] pci 0000:00:1f.0: LPC Generic IO decode 2 PIO at 0060-006f [ 0.416931] pci 0000:00:1f.2: reg 10 io port: [0x00-0x07] [ 0.416939] pci 0000:00:1f.2: reg 14 io port: [0x00-0x03] [ 0.416948] pci 0000:00:1f.2: reg 18 io port: [0x00-0x07] [ 0.416956] pci 0000:00:1f.2: reg 1c io port: [0x00-0x03] [ 0.416964] pci 0000:00:1f.2: reg 20 io port: [0x18b0-0x18bf] [ 0.416998] pci 0000:00:1f.2: PME# supported from D3hot [ 0.417003] pci 0000:00:1f.2: PME# disabled [ 0.417065] pci 0000:00:1f.3: reg 20 io port: [0x20a0-0x20bf] [ 0.417152] pci 0000:00:1c.0: bridge io port: [0x00-0xfff] [ 0.417157] pci 0000:00:1c.0: bridge 32bit mmio: [0x000000-0x0fffff] [ 0.417166] pci 0000:00:1c.0: bridge 64bit mmio pref: [0x000000-0x0fffff] [ 0.417222] pci 0000:00:1c.1: bridge io port: [0x00-0xfff] [ 0.417227] pci 0000:00:1c.1: bridge 32bit mmio: [0x000000-0x0fffff] [ 0.417235] pci 0000:00:1c.1: bridge 64bit mmio pref: [0x000000-0x0fffff] [ 0.417291] pci 0000:00:1c.2: bridge io port: [0x00-0xfff] [ 0.417296] pci 0000:00:1c.2: bridge 32bit mmio: [0x000000-0x0fffff] [ 0.417304] pci 0000:00:1c.2: bridge 64bit mmio pref: [0x000000-0x0fffff] [ 0.417354] pci 0000:06:01.0: reg 10 32bit mmio: [0xb0100000-0xb0100fff] [ 0.417382] pci 0000:06:01.0: supports D1 D2 [ 0.417384] pci 0000:06:01.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.417390] pci 0000:06:01.0: PME# disabled [ 0.417438] pci 0000:06:02.0: reg 10 io port: [0x3000-0x30ff] [ 0.417448] pci 0000:06:02.0: reg 14 32bit mmio: [0xb0101000-0xb01010ff] [ 0.417509] pci 0000:06:02.0: supports D1 D2 [ 0.417511] pci 0000:06:02.0: PME# supported from D1 D2 D3hot D3cold [ 0.417517] pci 0000:06:02.0: PME# disabled [ 0.417567] pci 0000:06:04.0: reg 10 32bit mmio: [0xb0102000-0xb0102fff] [ 0.417635] pci 0000:06:04.0: PME# supported from D0 D3hot D3cold [ 0.417641] pci 0000:06:04.0: PME# disabled [ 0.417697] pci 0000:00:1e.0: transparent bridge [ 0.417702] pci 0000:00:1e.0: bridge io port: [0x3000-0x3fff] [ 0.417707] pci 0000:00:1e.0: bridge 32bit mmio: [0xb0100000-0xb01fffff] [ 0.417759] pci_bus 0000:00: on NUMA node 0 [ 0.417765] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.418003] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] [ 0.420734] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 12 14 15) [ 0.420838] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 11 12 14 15) *10 [ 0.420940] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 [ 0.421042] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15) [ 0.421144] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 [ 0.421249] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled. [ 0.421351] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled. [ 0.421454] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15) [ 0.421648] SCSI subsystem initialized [ 0.421700] libata version 3.00 loaded. [ 0.421786] usbcore: registered new interface driver usbfs [ 0.421805] usbcore: registered new interface driver hub [ 0.421831] usbcore: registered new device driver usb [ 0.421966] ACPI: WMI: Mapper loaded [ 0.421968] PCI: Using ACPI for IRQ routing [ 0.421973] pci 0000:00:1c.0: BAR 13: can't allocate resource [ 0.421976] pci 0000:00:1c.0: BAR 14: can't allocate resource [ 0.421978] pci 0000:00:1c.0: BAR 15: can't allocate resource [ 0.421981] pci 0000:00:1c.1: BAR 13: can't allocate resource [ 0.421984] pci 0000:00:1c.1: BAR 14: can't allocate resource [ 0.421986] pci 0000:00:1c.1: BAR 15: can't allocate resource [ 0.421989] pci 0000:00:1c.2: BAR 13: can't allocate resource [ 0.421992] pci 0000:00:1c.2: BAR 14: can't allocate resource [ 0.421994] pci 0000:00:1c.2: BAR 15: can't allocate resource [ 0.422160] Bluetooth: Core ver 2.15 [ 0.422187] NET: Registered protocol family 31 [ 0.422189] Bluetooth: HCI device and connection manager initialized [ 0.422193] Bluetooth: HCI socket layer initialized [ 0.422196] NetLabel: Initializing [ 0.422198] NetLabel: domain hash size = 128 [ 0.422200] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.422216] NetLabel: unlabeled traffic allowed by default [ 0.422386] hpet clockevent registered [ 0.422390] HPET: 3 timers in total, 0 timers will be used for per-cpu timer [ 0.422397] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.422403] hpet0: 3 comparators, 64-bit 14.318180 MHz counter [ 0.429981] pnp: PnP ACPI init [ 0.429999] ACPI: bus type pnp registered [ 0.431368] pnp: PnP ACPI: found 8 devices [ 0.431371] ACPI: ACPI bus type pnp unregistered [ 0.431375] PnPBIOS: Disabled by ACPI PNP [ 0.431388] system 00:01: iomem range 0xe0000000-0xefffffff has been reserved [ 0.431392] system 00:01: iomem range 0xf0000000-0xf0003fff has been reserved [ 0.431396] system 00:01: iomem range 0xf0004000-0xf0004fff has been reserved [ 0.431399] system 00:01: iomem range 0xf0005000-0xf0005fff has been reserved [ 0.431403] system 00:01: iomem range 0xf0008000-0xf000bfff has been reserved [ 0.431407] system 00:01: iomem range 0xfed20000-0xfed3ffff has been reserved [ 0.431410] system 00:01: iomem range 0xfed45000-0xfed8ffff has been reserved [ 0.431418] system 00:04: ioport range 0x680-0x6ff has been reserved [ 0.431422] system 00:04: ioport range 0x800-0x80f has been reserved [ 0.431425] system 00:04: ioport range 0x1000-0x107f has been reserved [ 0.431429] system 00:04: ioport range 0x1180-0x11bf has been reserved [ 0.431432] system 00:04: ioport range 0x1600-0x167f has been reserved [ 0.466111] AppArmor: AppArmor Filesystem Enabled [ 0.466182] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:09 [ 0.466185] pci 0000:00:1c.0: IO window: disabled [ 0.466192] pci 0000:00:1c.0: MEM window: disabled [ 0.466196] pci 0000:00:1c.0: PREFETCH window: disabled [ 0.466202] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:0a [ 0.466204] pci 0000:00:1c.1: IO window: disabled [ 0.466210] pci 0000:00:1c.1: MEM window: disabled [ 0.466215] pci 0000:00:1c.1: PREFETCH window: disabled [ 0.466221] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:02 [ 0.466223] pci 0000:00:1c.2: IO window: disabled [ 0.466229] pci 0000:00:1c.2: MEM window: disabled [ 0.466234] pci 0000:00:1c.2: PREFETCH window: disabled [ 0.466243] pci 0000:06:01.0: CardBus bridge, secondary bus 0000:07 [ 0.466246] pci 0000:06:01.0: IO window: 0x003400-0x0034ff [ 0.466252] pci 0000:06:01.0: IO window: 0x003800-0x0038ff [ 0.466258] pci 0000:06:01.0: PREFETCH window: 0x60000000-0x63ffffff [ 0.466265] pci 0000:06:01.0: MEM window: 0x68000000-0x6bffffff [ 0.466271] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:06 [ 0.466275] pci 0000:00:1e.0: IO window: 0x3000-0x3fff [ 0.466282] pci 0000:00:1e.0: MEM window: 0xb0100000-0xb01fffff [ 0.466288] pci 0000:00:1e.0: PREFETCH window: 0x60000000-0x63ffffff [ 0.466302] alloc irq_desc for 17 on node -1 [ 0.466305] alloc kstat_irqs on node -1 [ 0.466311] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 0.466319] pci 0000:00:1c.0: setting latency timer to 64 [ 0.466327] alloc irq_desc for 16 on node -1 [ 0.466329] alloc kstat_irqs on node -1 [ 0.466333] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16 [ 0.466340] pci 0000:00:1c.1: setting latency timer to 64 [ 0.466348] alloc irq_desc for 18 on node -1 [ 0.466350] alloc kstat_irqs on node -1 [ 0.466354] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.466360] pci 0000:00:1c.2: setting latency timer to 64 [ 0.466369] pci 0000:00:1e.0: setting latency timer to 64 [ 0.466380] pci 0000:06:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.466388] pci_bus 0000:00: resource 0 io: [0x00-0xffff] [ 0.466391] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff] [ 0.466395] pci_bus 0000:09: resource 0 mem: [0x0-0xfff] [ 0.466398] pci_bus 0000:09: resource 1 mem: [0x0-0xfffff] [ 0.466401] pci_bus 0000:09: resource 2 mem: [0x0-0xfffff] [ 0.466404] pci_bus 0000:0a: resource 0 mem: [0x0-0xfff] [ 0.466407] pci_bus 0000:0a: resource 1 mem: [0x0-0xfffff] [ 0.466410] pci_bus 0000:0a: resource 2 mem: [0x0-0xfffff] [ 0.466413] pci_bus 0000:02: resource 0 mem: [0x0-0xfff] [ 0.466416] pci_bus 0000:02: resource 1 mem: [0x0-0xfffff] [ 0.466419] pci_bus 0000:02: resource 2 mem: [0x0-0xfffff] [ 0.466422] pci_bus 0000:06: resource 0 io: [0x3000-0x3fff] [ 0.466425] pci_bus 0000:06: resource 1 mem: [0xb0100000-0xb01fffff] [ 0.466429] pci_bus 0000:06: resource 2 pref mem [0x60000000-0x63ffffff] [ 0.466432] pci_bus 0000:06: resource 3 io: [0x00-0xffff] [ 0.466435] pci_bus 0000:06: resource 4 mem: [0x000000-0xffffffff] [ 0.466438] pci_bus 0000:07: resource 0 io: [0x3400-0x34ff] [ 0.466441] pci_bus 0000:07: resource 1 io: [0x3800-0x38ff] [ 0.466445] pci_bus 0000:07: resource 2 pref mem [0x60000000-0x63ffffff] [ 0.466448] pci_bus 0000:07: resource 3 mem: [0x68000000-0x6bffffff] [ 0.466487] NET: Registered protocol family 2 [ 0.466593] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.466940] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.468066] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.468767] TCP: Hash tables configured (established 131072 bind 65536) [ 0.468771] TCP reno registered [ 0.468909] NET: Registered protocol family 1 [ 0.468996] Trying to unpack rootfs image as initramfs... [ 0.741969] Freeing initrd memory: 8520k freed [ 0.748994] Simple Boot Flag at 0x36 set to 0x1 [ 0.749117] cpufreq-nforce2: No nForce2 chipset. [ 0.749162] Scanning for low memory corruption every 60 seconds [ 0.749321] audit: initializing netlink socket (disabled) [ 0.749357] type=2000 audit(1265706733.747:1): initialized [ 0.759637] highmem bounce pool size: 64 pages [ 0.759645] HugeTLB registered 4 MB page size, pre-allocated 0 pages [ 0.761298] VFS: Disk quotas dquot_6.5.2 [ 0.761360] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.761975] fuse init (API version 7.12) [ 0.762070] msgmni has been set to 1719 [ 0.762290] alg: No test for stdrng (krng) [ 0.762304] io scheduler noop registered [ 0.762306] io scheduler anticipatory registered [ 0.762309] io scheduler deadline registered [ 0.762355] io scheduler cfq registered (default) [ 0.762371] pci 0000:00:02.0: Boot video device [ 0.762574] pcieport-driver 0000:00:1c.0: setting latency timer to 64 [ 0.762728] pcieport-driver 0000:00:1c.1: setting latency timer to 64 [ 0.762881] pcieport-driver 0000:00:1c.2: setting latency timer to 64 [ 0.762991] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.763083] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.800072] ACPI: AC Adapter [ACAD] (on-line) [ 0.800141] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 0.800146] ACPI: Power Button [PWRF] [ 0.800216] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1 [ 0.840009] ACPI: Lid Switch [LID] [ 0.840062] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2 [ 0.840065] ACPI: Power Button [PWRB] [ 0.840422] Marking TSC unstable due to TSC halts in idle [ 0.840454] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3]) [ 0.840481] processor LNXCPU:00: registered as cooling_device0 [ 0.844465] Switched to high resolution mode on CPU 0 [ 0.920072] thermal LNXTHERM:01: registered as thermal_zone0 [ 0.920082] ACPI: Thermal Zone [THRM] (43 C) [ 0.920131] isapnp: Scanning for PnP cards... [ 0.925715] ACPI: Battery Slot [BAT1] (battery absent) [ 1.274414] isapnp: No Plug & Play device found [ 1.275616] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 1.275989] alloc irq_desc for 20 on node -1 [ 1.275992] alloc kstat_irqs on node -1 [ 1.276017] serial 0000:00:1e.3: PCI INT B -> GSI 20 (level, low) -> IRQ 20 [ 1.276025] serial 0000:00:1e.3: PCI INT B disabled [ 1.277057] brd: module loaded [ 1.277552] loop: module loaded [ 1.277635] input: Macintosh mouse button emulation as /devices/virtual/input/input3 [ 1.277714] ahci 0000:00:1f.2: version 3.0 [ 1.277724] alloc irq_desc for 19 on node -1 [ 1.277727] alloc kstat_irqs on node -1 [ 1.277731] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1.277744] ahci 0000:00:1f.2: PCI INT B disabled [ 1.277748] ahci: probe of 0000:00:1f.2 failed with error -22 [ 1.277790] ata_piix 0000:00:1f.2: version 2.13 [ 1.277797] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1.277803] ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ] [ 1.432022] ata_piix 0000:00:1f.2: setting latency timer to 64 [ 1.432110] scsi0 : ata_piix [ 1.432195] scsi1 : ata_piix [ 1.432303] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x18b0 irq 14 [ 1.432306] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x18b8 irq 15 [ 1.433226] Fixed MDIO Bus: probed [ 1.433266] PPP generic driver version 2.4.2 [ 1.433356] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.433375] alloc irq_desc for 23 on node -1 [ 1.433377] alloc kstat_irqs on node -1 [ 1.433382] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 1.433395] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 1.433399] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 1.433450] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 1.437365] ehci_hcd 0000:00:1d.7: debug port 1 [ 1.437372] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported [ 1.437621] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xb0040000 [ 1.452018] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 1.452103] usb usb1: configuration #1 chosen from 1 choice [ 1.452136] hub 1-0:1.0: USB hub found [ 1.452146] hub 1-0:1.0: 8 ports detected [ 1.452231] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.452250] uhci_hcd: USB Universal Host Controller Interface driver [ 1.452275] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 1.452282] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 1.452286] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 1.452321] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 1.452348] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001820 [ 1.452439] usb usb2: configuration #1 chosen from 1 choice [ 1.452467] hub 2-0:1.0: USB hub found [ 1.452475] hub 2-0:1.0: 2 ports detected [ 1.452530] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1.452537] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 1.452541] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 1.452574] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 1.452609] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001840 [ 1.452691] usb usb3: configuration #1 chosen from 1 choice [ 1.452723] hub 3-0:1.0: USB hub found [ 1.452730] hub 3-0:1.0: 2 ports detected [ 1.452832] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 1.455970] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 1.455978] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 1.456052] mice: PS/2 mouse device common for all mice [ 1.456166] rtc_cmos 00:05: RTC can wake from S4 [ 1.456206] rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0 [ 1.456239] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs [ 1.456349] device-mapper: uevent: version 1.0.3 [ 1.456435] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@xxxxxxxxxx [ 1.456518] device-mapper: multipath: version 1.1.0 loaded [ 1.456521] device-mapper: multipath round-robin: version 1.0.0 loaded [ 1.456643] EISA: Probing bus 0 at eisa.0 [ 1.456650] Cannot allocate resource for EISA slot 1 [ 1.456653] Cannot allocate resource for EISA slot 2 [ 1.456656] Cannot allocate resource for EISA slot 3 [ 1.456676] EISA: Detected 0 cards. [ 1.456772] cpuidle: using governor ladder [ 1.456855] cpuidle: using governor menu [ 1.457359] TCP cubic registered [ 1.457532] NET: Registered protocol family 10 [ 1.458004] lo: Disabled Privacy Extensions [ 1.458332] NET: Registered protocol family 17 [ 1.458349] Bluetooth: L2CAP ver 2.13 [ 1.458351] Bluetooth: L2CAP socket layer initialized [ 1.458354] Bluetooth: SCO (Voice Link) ver 0.6 [ 1.458356] Bluetooth: SCO socket layer initialized [ 1.458385] Bluetooth: RFCOMM TTY layer initialized [ 1.458389] Bluetooth: RFCOMM socket layer initialized [ 1.458391] Bluetooth: RFCOMM ver 1.11 [ 1.458631] Using IPI No-Shortcut mode [ 1.458699] PM: Resume from disk failed. [ 1.458715] registered taskstats version 1 [ 1.458821] Magic number: 14:769:221 [ 1.458895] rtc_cmos 00:05: setting system clock to 2010-02-09 09:12:15 UTC (1265706735) [ 1.458899] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 1.458901] EDD information not available. [ 1.487787] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4 [ 1.600763] ata2.00: ATAPI: MATSHITADVD-RAM UJ-841S, 1.50, max UDMA/33 [ 1.601106] ata1.00: ATA-6: TOSHIBA MK4032GSX, AS211G, max UDMA/100 [ 1.601110] ata1.00: 78140160 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 1.616701] ata2.00: configured for UDMA/33 [ 1.616966] ata1.00: configured for UDMA/100 [ 1.617131] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK4032GS AS21 PQ: 0 ANSI: 5 [ 1.617252] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 1.617296] sd 0:0:0:0: [sda] 78140160 512-byte logical blocks: (40.0 GB/37.2 GiB) [ 1.617348] sd 0:0:0:0: [sda] Write Protect is off [ 1.617351] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.617378] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.617510] sda: [ 1.619478] scsi 1:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-841S 1.50 PQ: 0 ANSI: 5 [ 1.623910] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 1.623915] Uniform CD-ROM driver Revision: 3.20 [ 1.623996] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 1.624047] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 1.644560] sda1 sda2 [ 1.644785] sd 0:0:0:0: [sda] Attached SCSI disk [ 1.644801] Freeing unused kernel memory: 540k freed [ 1.645130] Write protecting the kernel text: 4568k [ 1.645171] Write protecting the kernel read-only data: 1836k [ 1.817000] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:01/input/input5 [ 1.817047] ACPI: Video Device [GFX0] (multi-head: yes rom: yes post: no) [ 1.819938] Linux agpgart interface v0.103 [ 1.823966] agpgart-intel 0000:00:00.0: Intel 915GM Chipset [ 1.858888] agpgart-intel 0000:00:00.0: detected 7932K stolen memory [ 1.861560] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000 [ 1.863006] <6>8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) [ 1.863033] 8139cp 0000:06:02.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too [ 1.866539] 8139too Fast Ethernet driver 0.9.28 [ 1.866574] 8139too 0000:06:02.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 [ 1.867839] eth0: RealTek RTL8139 at 0x3000, 00:16:36:0a:d0:54, IRQ 19 [ 1.920023] Clocksource tsc unstable (delta = -177930906 ns) [ 1.958122] [drm] Initialized drm 1.1.0 20060810 [ 1.975219] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 1.975228] i915 0000:00:02.0: setting latency timer to 64 [ 2.577530] [drm] DAC-6: set mode 640x480 0 [ 2.804863] [drm] TV-14: set mode NTSC 480i 0 [ 2.931530] [drm] fb0: inteldrmfb frame buffer device [ 2.931542] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 2.994463] render error detected, EIR: 0x00000010 [ 2.994466] page table error [ 2.994468] PGTBL_ER: 0x00000100 [ 2.994471] [drm:i915_handle_error] *ERROR* EIR stuck: 0x00000010, masking [ 2.994479] render error detected, EIR: 0x00000010 [ 2.994481] page table error [ 2.994482] PGTBL_ER: 0x00000100 [ 3.003762] [drm] LVDS-8: set mode 1024x768 17 [ 3.028188] Console: switching to colour frame buffer device 128x48 [ 3.259525] xor: automatically using best checksumming function: pIII_sse [ 3.276008] pIII_sse : 4494.000 MB/sec [ 3.276011] xor: using function: pIII_sse (4494.000 MB/sec) [ 3.279652] device-mapper: dm-raid45: initialized v0.2594b [ 1205.917073] PM: Starting manual resume from disk [ 1205.917078] PM: Resume from partition 252:2 [ 1205.917080] PM: Checking hibernation image. [ 1205.917350] PM: Resume from disk failed. [ 1205.928444] EXT4-fs (dm-1): INFO: recovery required on readonly filesystem [ 1205.928449] EXT4-fs (dm-1): write access will be enabled during recovery [ 1205.961498] EXT4-fs (dm-1): barriers enabled [ 1209.998600] kjournald2 starting: pid 486, dev dm-1:8, commit interval 5 seconds [ 1209.998627] EXT4-fs (dm-1): delayed allocation enabled [ 1209.998631] EXT4-fs: file extents enabled [ 1209.999770] EXT4-fs: mballoc enabled [ 1209.999786] EXT4-fs (dm-1): orphan cleanup on readonly fs [ 1209.999795] EXT4-fs (dm-1): ext4_orphan_cleanup: deleting unreferenced inode 31421 [ 1209.999920] EXT4-fs (dm-1): ext4_orphan_cleanup: deleting unreferenced inode 31420 [ 1209.999934] EXT4-fs (dm-1): 2 orphan inodes deleted [ 1209.999938] EXT4-fs (dm-1): recovery complete [ 1210.316817] EXT4-fs (dm-1): mounted filesystem with ordered data mode [ 1211.301088] type=1505 audit(1265707945.341:2): operation="profile_load" pid=513 name=/usr/share/gdm/guest-session/Xsession [ 1211.305059] type=1505 audit(1265707945.345:3): operation="profile_load" pid=514 name=/sbin/dhclient3 [ 1211.305791] type=1505 audit(1265707945.345:4): operation="profile_load" pid=514 name=/usr/lib/NetworkManager/nm-dhcp-client.action [ 1211.306191] type=1505 audit(1265707945.345:5): operation="profile_load" pid=514 name=/usr/lib/connman/scripts/dhclient-script [ 1211.370435] type=1505 audit(1265707945.409:6): operation="profile_load" pid=515 name=/usr/bin/evince [ 1211.382458] type=1505 audit(1265707945.421:7): operation="profile_load" pid=515 name=/usr/bin/evince-previewer [ 1211.389474] type=1505 audit(1265707945.429:8): operation="profile_load" pid=515 name=/usr/bin/evince-thumbnailer [ 1211.416133] type=1505 audit(1265707945.457:9): operation="profile_load" pid=517 name=/usr/bin/freshclam [ 1211.448978] type=1505 audit(1265707945.489:10): operation="profile_load" pid=518 name=/usr/lib/cups/backend/cups-pdf [ 1211.449839] type=1505 audit(1265707945.489:11): operation="profile_load" pid=518 name=/usr/sbin/cupsd [ 1230.023276] Adding 2928632k swap on /dev/mapper/PBubuntu-Swap. Priority:-1 extents:1 across:2928632k [ 1230.112893] udev: starting version 147 [ 1230.211473] lp: driver loaded but no devices found [ 1230.856626] EXT4-fs (dm-1): internal journal on dm-1:8 [ 1231.024090] EXT4-fs (sda1): barriers enabled [ 1231.078508] kjournald2 starting: pid 748, dev sda1:8, commit interval 5 seconds [ 1231.226447] EXT4-fs (sda1): internal journal on sda1:8 [ 1231.226454] EXT4-fs (sda1): delayed allocation enabled [ 1231.226459] EXT4-fs: file extents enabled [ 1231.226653] EXT4-fs: mballoc enabled [ 1231.226673] EXT4-fs (sda1): mounted filesystem with ordered data mode [ 1231.253608] intel_rng: FWH not detected [ 1231.282672] yenta_cardbus 0000:06:01.0: CardBus bridge found [1179:ff31] [ 1231.282698] yenta_cardbus 0000:06:01.0: Using CSCINT to route CSC interrupts to PCI [ 1231.282701] yenta_cardbus 0000:06:01.0: Routing CardBus interrupts to PCI [ 1231.282708] yenta_cardbus 0000:06:01.0: TI: mfunc 0x015c1d22, devctl 0x44 [ 1231.284652] lib80211: common routines for IEEE802.11 drivers [ 1231.284655] lib80211_crypt: registered algorithm 'NULL' [ 1231.289583] ieee80211: 802.11 data/management/control stack, git-1.1.13 [ 1231.289585] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@xxxxxxxxxxxxxxx> [ 1231.327948] ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.2.2kmprq [ 1231.327953] ipw2200: Copyright(c) 2003-2006 Intel Corporation [ 1231.355039] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1231.419100] Intel ICH 0000:00:1e.2: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1231.419144] Intel ICH 0000:00:1e.2: setting latency timer to 64 [ 1231.516784] yenta_cardbus 0000:06:01.0: ISA IRQ mask 0x0cf8, PCI irq 16 [ 1231.516791] yenta_cardbus 0000:06:01.0: Socket status: 30000007 [ 1231.516796] pci_bus 0000:06: Raising subordinate bus# of parent bus (#06) from #07 to #08 [ 1231.516805] yenta_cardbus 0000:06:01.0: pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff [ 1231.516810] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3000-0x3fff: clean. [ 1231.517048] yenta_cardbus 0000:06:01.0: pcmcia: parent PCI bridge Memory window: 0xb0100000 - 0xb01fffff [ 1231.517052] yenta_cardbus 0000:06:01.0: pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x63ffffff [ 1231.518281] ipw2200 0000:06:04.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 1231.518356] ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection [ 1231.518409] ipw2200 0000:06:04.0: firmware: requesting ipw2200-bss.fw [ 1231.759467] ipw2200: Radio Frequency Kill Switch is On: [ 1231.759470] Kill switch must be turned off for wireless networking to work. [ 1231.759792] intel8x0_measure_ac97_clock: measured 77121 usecs (3712 samples) [ 1231.759796] intel8x0: clocking to 48000 [ 1231.762983] ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels) [ 1232.016500] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04713/0x0 [ 1232.016511] synaptics: Toshiba Satellite L20 detected, limiting rate to 40pps. [ 1232.050253] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input6 [ 1232.144865] hsfengine: module license 'see LICENSE file distributed with driver' taints kernel. [ 1232.144871] Disabling lock debugging due to kernel taint [ 1232.236930] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x100-0x3af: clean. [ 1232.238637] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7 [ 1232.239358] pcmcia_socket pcmcia_socket0: cs: IO port probe 0x820-0x8ff: clean. [ 1232.239953] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xc00-0xcf7: clean. [ 1232.240742] pcmcia_socket pcmcia_socket0: cs: IO port probe 0xa00-0xaff: clean. [ 1232.264588] hsfich 0000:00:1e.3: PCI INT B -> GSI 20 (level, low) -> IRQ 20 [ 1233.219827] BUG: unable to handle kernel paging request at 1f6e7000 [ 1233.219903] IP: [<f958b574>] hsfengine1272_+0x9a3/0x110b [hsfengine] [ 1233.220009] *pde = 00000000 [ 1233.220009] Oops: 0000 [#1] SMP [ 1233.220009] last sysfs file: /sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/uevent [ 1233.220009] Modules linked in: hsfmc97ich(+) hsfserial joydev hsfengine(P) pcmcia hsfosspec snd_intel8x0 snd_ac97_codec ac97_bus snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_dummy iptable_filter snd_seq_oss ip_tables x_tables hsfsoar psmouse serio_raw ipw2200 libipw lib80211 yenta_socket rsrc_nonstatic pcmcia_core snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device snd soundcore snd_page_alloc lp parport sha256_generic blowfish cbc dm_crypt dm_raid45 xor fbcon tileblit font bitblit softcursor i915 drm i2c_algo_bit 8139too 8139cp mii intel_agp agpgart video output [ 1233.220009] [ 1233.220009] Pid: 671, comm: modprobe Tainted: P (2.6.31-19-generic #56-Ubuntu) Satellite L20 [ 1233.220009] EIP: 0060:[<f958b574>] EFLAGS: 00010206 CPU: 0 [ 1233.220009] EIP is at hsfengine1272_+0x9a3/0x110b [hsfengine] [ 1233.220009] EAX: 5f6e7000 EBX: 6e55a180 ECX: 00007000 EDX: 00000000 [ 1233.220009] ESI: 00000000 EDI: 1f6e7000 EBP: f20fdcac ESP: f20fdc54 [ 1233.220009] DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 [ 1233.220009] Process modprobe (pid: 671, ti=f20fc000 task=f2181920 task.ti=f20fc000) [ 1233.220009] Stack: [ 1233.220009] c0570eda c084b4a0 f20fdc8c c0000000 c0100000 6e55a180 0000001d c00f6c90 [ 1233.220009] <0> 00000000 00000000 00000000 0000005f 00000000 00000000 00000000 deadaffe [ 1233.220009] <0> 00000000 00000000 ba6b551d f1a2e540 f1810508 f1a2e56c f20fdcdc f9586060 [ 1233.220009] Call Trace: [ 1233.220009] [<c0570eda>] ? _spin_lock_irqsave+0x2a/0x40 [ 1233.220009] [<f9586060>] ? hsfengine1461_+0x70/0xb0 [hsfengine] [ 1233.220009] [<f9585c8d>] ? hsfengine494_+0x1d/0x40 [hsfengine] [ 1233.220009] [<f955f45a>] ? cnxthsf_7800205full_ComCtrl_Open +0x6a/0x2e0 [hsfengine] [ 1233.220009] [<f96b9c4e>] ? cnxthsf_7800205full_cnxt_serial_add +0x20e/0x520 [hsfserial] [ 1233.220009] [<c056eb1c>] ? printk+0x18/0x1c [ 1233.220009] [<c034dc15>] ? acpi_pci_irq_enable+0x1bb/0x1dd [ 1233.220009] [<c0318354>] ? vsnprintf+0xa4/0x400 [ 1233.220009] [<f96b9fc0>] ? cnxt_event_handler+0x0/0x2c0 [hsfserial] [ 1233.220009] [<f96e689a>] ? cnxthwpci_probe+0x210/0x256 [hsfmc97ich] [ 1233.220009] [<c032877e>] ? local_pci_probe+0xe/0x10 [ 1233.220009] [<c0329500>] ? pci_device_probe+0x60/0x80 [ 1233.220009] [<c03a3000>] ? really_probe+0x50/0x140 [ 1233.220009] [<c0570eda>] ? _spin_lock_irqsave+0x2a/0x40 [ 1233.220009] [<c03a3109>] ? driver_probe_device+0x19/0x20 [ 1233.220009] [<c03a3189>] ? __driver_attach+0x79/0x80 [ 1233.220009] [<c03a2658>] ? bus_for_each_dev+0x48/0x70 [ 1233.220009] [<c03a2ec9>] ? driver_attach+0x19/0x20 [ 1233.220009] [<c03a3110>] ? __driver_attach+0x0/0x80 [ 1233.220009] [<c03a28af>] ? bus_add_driver+0xbf/0x2a0 [ 1233.220009] [<c0329440>] ? pci_device_remove+0x0/0x40 [ 1233.220009] [<c03a3415>] ? driver_register+0x65/0x120 [ 1233.220009] [<c0329720>] ? __pci_register_driver+0x40/0xb0 [ 1233.220009] [<f96ef0cb>] ? cnxthwpci_init+0xcb/0xd2 [hsfmc97ich] [ 1233.220009] [<c010112c>] ? do_one_initcall+0x2c/0x190 [ 1233.220009] [<f96ef000>] ? cnxthwpci_init+0x0/0xd2 [hsfmc97ich] [ 1233.220009] [<c0173691>] ? sys_init_module+0xb1/0x1f0 [ 1233.220009] [<c010336c>] ? syscall_call+0x7/0xb [ 1233.220009] Code: 45 c8 00 00 00 00 c7 c3 4c b6 6b e1 29 e3 c7 c3 8d 08 44 fb c1 e1 08 c7 c3 05 b1 03 42 89 cb 89 c3 ff cb 8b 5d bc 09 c8 8d 3c 38 <8a> 07 48 3c 01 0f 86 4f 12 00 00 e9 6a 14 00 00 89 d7 88 c8 e6 [ 1233.220009] EIP: [<f958b574>] hsfengine1272_+0x9a3/0x110b [hsfengine] SS:ESP 0068:f20fdc54 [ 1233.220009] CR2: 000000001f6e7000 [ 1233.251775] ---[ end trace 12d05075119e6d90 ]--- [ 1237.050448] EXT4-fs (dm-3): barriers enabled [ 1237.074247] kjournald2 starting: pid 1050, dev dm-3:8, commit interval 5 seconds [ 1237.076454] EXT4-fs (dm-3): internal journal on dm-3:8 [ 1237.078293] EXT4-fs (dm-3): delayed allocation enabled [ 1237.080126] EXT4-fs: file extents enabled [ 1237.082266] EXT4-fs: mballoc enabled [ 1237.084059] EXT4-fs (dm-3): mounted filesystem with ordered data mode [ 1237.306015] eth0: link down [ 1237.321136] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 1237.324776] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 1237.668118] __ratelimit: 3 callbacks suppressed [ 1237.668123] type=1505 audit(1265707971.709:13): operation="profile_replace" pid=1241 name=/usr/share/gdm/guest-session/Xsession [ 1237.675986] type=1505 audit(1265707971.713:14): operation="profile_replace" pid=1244 name=/sbin/dhclient3 [ 1237.676787] type=1505 audit(1265707971.717:15): operation="profile_replace" pid=1244 name=/usr/lib/NetworkManager/nm-dhcp-client.action [ 1237.677192] type=1505 audit(1265707971.717:16): operation="profile_replace" pid=1244 name=/usr/lib/connman/scripts/dhclient-script [ 1237.698471] type=1505 audit(1265707971.737:17): operation="profile_replace" pid=1245 name=/usr/bin/evince [ 1237.722061] type=1505 audit(1265707971.761:18): operation="profile_replace" pid=1245 name=/usr/bin/evince-previewer [ 1237.729084] type=1505 audit(1265707971.769:19): operation="profile_replace" pid=1245 name=/usr/bin/evince-thumbnailer [ 1237.738555] type=1505 audit(1265707971.777:20): operation="profile_replace" pid=1248 name=/usr/bin/freshclam [ 1237.740525] type=1505 audit(1265707971.781:21): operation="profile_replace" pid=1249 name=/usr/lib/cups/backend/cups-pdf [ 1237.741390] type=1505 audit(1265707971.781:22): operation="profile_replace" pid=1249 name=/usr/sbin/cupsd [ 1237.796867] [drm] DAC-6: set mode 640x480 0 [ 1237.925268] [drm] DAC-6: set mode 640x480 0 [ 1238.145430] [drm] TV-14: set mode NTSC 480i 0 [ 1238.335656] [drm] TV-14: set mode NTSC 480i 0 [ 1238.583785] [drm] DAC-6: set mode 640x480 0 [ 1238.689129] [drm] DAC-6: set mode 640x480 0 [ 1238.913834] [drm] TV-14: set mode NTSC 480i 0 [ 1239.077446] [drm] TV-14: set mode NTSC 480i 0 [ 1240.999552] [drm] DAC-6: set mode 640x480 0 [ 1241.105147] [drm] DAC-6: set mode 640x480 0 [ 1241.308606] [drm] TV-14: set mode NTSC 480i 0 [ 1241.448818] [drm] TV-14: set mode NTSC 480i 0 [ 1241.596205] [drm] DAC-6: set mode 640x480 0 [ 1241.701607] [drm] DAC-6: set mode 640x480 0 [ 1241.905066] [drm] TV-14: set mode NTSC 480i 0 [ 1242.045449] [drm] TV-14: set mode NTSC 480i 0 [ 1242.209152] [drm] DAC-6: set mode 640x480 0 [ 1242.314556] [drm] DAC-6: set mode 640x480 0 [ 1242.519249] [drm] TV-14: set mode NTSC 480i 0 [ 1242.659885] [drm] TV-14: set mode NTSC 480i 0 [ 1259.065193] [drm] DAC-6: set mode 640x480 0 [ 1259.221763] [drm] DAC-6: set mode 640x480 0 [ 1259.424973] [drm] TV-14: set mode NTSC 480i 0 [ 1259.565184] [drm] TV-14: set mode NTSC 480i 0 [ 1259.740263] [drm] DAC-6: set mode 640x480 0 [ 1259.859072] [drm] DAC-6: set mode 640x480 0 [ 1260.066940] [drm] TV-14: set mode NTSC 480i 0 [ 1260.231941] [drm] TV-14: set mode NTSC 480i 0 [ 1260.383898] [drm] DAC-6: set mode 640x480 0 [ 1260.493215] [drm] DAC-6: set mode 640x480 0 [ 1260.696969] [drm] TV-14: set mode NTSC 480i 0 [ 1260.837479] [drm] TV-14: set mode NTSC 480i 0 [ 1262.248499] [drm] DAC-6: set mode 640x480 0 [ 1262.403508] [drm] DAC-6: set mode 640x480 0 [ 1262.612974] [drm] TV-14: set mode NTSC 480i 0 [ 1262.722536] ppdev: user-space parallel port driver [ 1262.773180] [drm] TV-14: set mode NTSC 480i 0 [ 1816.148058] usb 1-2: new high speed USB device using ehci_hcd and address 2 [ 1816.290124] usb 1-2: configuration #1 chosen from 1 choice [ 1816.363702] Initializing USB Mass Storage driver... [ 1816.365751] scsi2 : SCSI emulation for USB Mass Storage devices [ 1816.366052] usbcore: registered new interface driver usb-storage [ 1816.366061] USB Mass Storage support registered. [ 1816.367087] usb-storage: device found at 2 [ 1816.367092] usb-storage: waiting for device to settle before scanning [ 1821.364561] usb-storage: device scan complete [ 1821.367428] scsi 2:0:0:0: Direct-Access Generic STORAGE DEVICE 9228 PQ: 0 ANSI: 0 [ 1821.368264] sd 2:0:0:0: Attached scsi generic sg2 type 0 [ 1821.521024] sd 2:0:0:0: [sdb] 1984000 512-byte logical blocks: (1.01 GB/968 MiB) [ 1821.522262] sd 2:0:0:0: [sdb] Write Protect is off [ 1821.522271] sd 2:0:0:0: [sdb] Mode Sense: 03 00 00 00 [ 1821.522277] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 1821.528038] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 1821.528048] sdb: sdb1 [ 1821.540152] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 1821.540163] sd 2:0:0:0: [sdb] Attached SCSI removable disk [ 1860.851602] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 1860.851609] sdb: unknown partition table [ 1861.397297] sd 2:0:0:0: [sdb] Assuming drive cache: write through [ 1861.397305] sdb: [ 1952.359048] ISO 9660 Extensions: Microsoft Joliet Level 3 [ 1952.359119] ISO 9660 Extensions: RRIP_1991A [ 3811.316054] usb 1-1: new high speed USB device using ehci_hcd and address 3 [ 3811.449166] usb 1-1: configuration #1 chosen from 1 choice [ 3811.477570] scsi3 : SCSI emulation for USB Mass Storage devices [ 3811.477689] usb-storage: device found at 3 [ 3811.477691] usb-storage: waiting for device to settle before scanning [ 3816.476221] usb-storage: device scan complete [ 3816.477837] scsi 3:0:0:0: Direct-Access RIM BlackBerry SD 0001 PQ: 0 ANSI: 0 CCS [ 3816.478651] sd 3:0:0:0: Attached scsi generic sg3 type 0 [ 3816.502631] sd 3:0:0:0: [sdc] Attached SCSI removable disk [ 3963.120217] eth0: link up, 10Mbps, half-duplex, lpa 0x0000 [ 3963.120692] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 3970.669357] process `skype' is using obsolete setsockopt SO_BSDCOMPAT [ 3973.264033] eth0: no IPv6 routers present [ 3989.018913] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 3989.018923] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 3990.012007] atkbd.c: Unknown key released (translated set 2, code 0x55 on isa0060/serio0). [ 3990.012017] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4042.262668] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4042.262678] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4042.504340] atkbd.c: Unknown key released (translated set 2, code 0x55 on isa0060/serio0). [ 4042.504350] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4096.261076] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4096.261086] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4096.477094] atkbd.c: Unknown key released (translated set 2, code 0x55 on isa0060/serio0). [ 4096.477104] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4108.227326] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4108.227336] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4108.448853] atkbd.c: Unknown key released (translated set 2, code 0x55 on isa0060/serio0). [ 4108.448862] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4886.276628] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4886.276639] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4886.535397] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4886.535406] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4886.570082] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4886.570092] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4886.615943] atkbd.c: Unknown key released (translated set 2, code 0x55 on isa0060/serio0). [ 4886.615951] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4909.972082] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4909.972093] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4910.217865] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4910.217875] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4910.253646] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4910.253654] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4910.288354] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4910.288363] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4910.324143] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4910.324152] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4910.358843] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4910.358851] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4910.394650] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4910.394660] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4910.429336] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4910.429344] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4910.465128] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4910.465137] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4910.499833] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4910.499842] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4910.535626] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4910.535635] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4910.570335] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4910.570345] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4910.606123] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4910.606131] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4910.640820] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4910.640828] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4910.677370] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4910.677380] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4910.711332] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 4910.711341] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 4910.837763] atkbd.c: Unknown key released (translated set 2, code 0x55 on isa0060/serio0). [ 4910.837773] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 5163.513426] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 5163.513437] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 5163.679007] atkbd.c: Unknown key released (translated set 2, code 0x55 on isa0060/serio0). [ 5163.679017] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 5282.917187] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 5282.917198] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 5283.113799] atkbd.c: Unknown key released (translated set 2, code 0x55 on isa0060/serio0). [ 5283.113809] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 5491.810445] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 5491.810456] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 5492.056760] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 5492.056770] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 5492.147244] atkbd.c: Unknown key released (translated set 2, code 0x55 on isa0060/serio0). [ 5492.147255] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 6694.822532] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 6694.822543] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 6695.098909] atkbd.c: Unknown key released (translated set 2, code 0x55 on isa0060/serio0). [ 6695.098919] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 6700.335968] atkbd.c: Unknown key pressed (translated set 2, code 0x55 on isa0060/serio0). [ 6700.335979] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. [ 6700.538091] atkbd.c: Unknown key released (translated set 2, code 0x55 on isa0060/serio0). [ 6700.538101] atkbd.c: Use 'setkeycodes 55 <keycode>' to make it known. Module Size Used by nls_iso8859_1 3740 1 nls_cp437 5372 1 vfat 10716 1 fat 51452 1 vfat usb_storage 52576 1 binfmt_misc 8356 1 hsfmc97ich 67310 1 hsfserial 21124 1 hsfmc97ich joydev 10240 0 hsfengine 1298720 2 hsfmc97ich,hsfserial pcmcia 36808 0 hsfosspec 111628 4 hsfmc97ich,hsfserial,hsfengine snd_intel8x0 30168 2 snd_ac97_codec 101216 1 snd_intel8x0 ac97_bus 1532 1 snd_ac97_codec snd_pcm_oss 37920 0 snd_mixer_oss 16028 1 snd_pcm_oss snd_pcm 75296 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_seq_dummy 2656 0 iptable_filter 3100 0 snd_seq_oss 28576 0 ip_tables 11692 1 iptable_filter x_tables 16544 1 ip_tables hsfsoar 93496 1 hsfmc97ich psmouse 56500 0 serio_raw 5280 0 ipw2200 140292 0 libipw 43148 1 ipw2200 lib80211 6432 2 ipw2200,libipw yenta_socket 24296 1 rsrc_nonstatic 11644 1 yenta_socket pcmcia_core 36528 3 pcmcia,yenta_socket,rsrc_nonstatic snd_seq_midi 6432 0 snd_rawmidi 22208 1 snd_seq_midi snd_seq_midi_event 6940 2 snd_seq_oss,snd_seq_midi snd_seq 50224 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event snd_timer 22276 2 snd_pcm,snd_seq snd_seq_device 6920 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq snd 59204 14 snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 7264 1 snd snd_page_alloc 9156 2 snd_intel8x0,snd_pcm lp 8964 0 parport 35340 1 lp sha256_generic 11580 0 blowfish 7772 2 cbc 3516 1 dm_crypt 12928 1 dm_raid45 84228 0 xor 15620 1 dm_raid45 fbcon 36640 72 tileblit 2460 1 fbcon font 8124 1 fbcon bitblit 5372 1 fbcon softcursor 1756 1 bitblit i915 221320 3 drm 159584 3 i915 i2c_algo_bit 5760 1 i915 8139too 22620 0 8139cp 19260 0 mii 5212 2 8139too,8139cp intel_agp 27484 2 i915 agpgart 34988 2 drm,intel_agp video 19380 1 i915 output 2780 1 video
