Diaco,
scanModem reports that you need hsfmodem drivers:
For candidate modem in: 00:1b.0
0403 Audio device: Intel Corporation 82801G
Primary device ID: 8086:27d8
Subsystem PCI_id 104d:81ef
Softmodem codec or chipset from diagnostics: 0x14f12bfa
from Archives:
The HDA card softmodem chip is 0x14f12bfa
Support type needed or chipset: hsfmodem
Writing DOCs/Intel.txt
For owners of a Dell PCs with Conexant HSF modems, a driver source
package with full speed enabled is available, but requires driver
compiling. Read DOCs/Conexant.txt
>From http://www.linuxant.com/drivers/hsf/full/downloads-ubuntu-x86.php
download hsfmodem-7.80.02.02full_k2.6.28_13_generic_ubuntu_i386.deb.zip
Under Linux unpack with:
$ unzip hsfmodem*.zip
Then install with:
$ sudo dpkg -i hsfmodem*.deb
Subsequently, the modem should be found with
$ sudo wvdialconf /etc/wvdial.conf
Edit in your personal information with:
$ sudo gedit /etc/wvdial.conf
and try dialing out with:
$ sudo wvdial.
See DOCs/Testing.txt for details.
After installing your modem drivers and the modem is unresponsive,
scanModem also reports the following:
Modem interrupt assignment and sharing:
22: 474142 0 IO-APIC-fasteoi HDA Intel
--- Bootup diagnostics for card in PCI slot 00:1b.0 ----
[ 0.500340] pci 0000:00:1b.0: reg 10 64bit mmio: [0xd2300000-0xd2303fff]
[ 0.500382] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.500387] pci 0000:00:1b.0: PME# disabled
[ 16.708263] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level,
low) -> IRQ 22
[ 16.708316] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 5875.585088] HDA Intel 0000:00:1b.0: PCI INT A disabled
[ 5876.604097] HDA Intel 0000:00:1b.0: restoring config space at
offset 0x1 (was 0x100006, writing 0x100002)
[ 5876.604129] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level,
low) -> IRQ 22
[ 5876.604139] HDA Intel 0000:00:1b.0: setting latency timer to 64
The PCI slot 00:1b.0 of the modem card may be disabled early in
a bootup process, but then enabled later. If modem drivers load
but the modem is not responsive, read DOCs/Bootup.txt about possible fixes.
Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
if help is needed.
Regards,
Antonio
On Tue, Sep 15, 2009 at 11:19 AM, Diaco <s.diaco@xxxxxxxxx> wrote:
> Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List
> Server,
> as HTML can contain viruses. Use as the email Subject Line:
> YourName, YourCountry kernel 2.6.28-13-generic
> With this Subject Line cogent experts will be alerted, and useful case names
> left in the Archive.
> YourCountry will enable Country specific guidance. Linux experts in
> YourCountry
> can be found through: http://www.linux.org/groups/index.html.
> They will know your Country's modem code, which may be essential for dialup
> service.
> Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an Internet
> Provider mail filters.
> So in a day, also check the Archived responses at http://www.linmodems.org
> -------------------------- System information ----------------------------
> CPU=i686, Linux version 2.6.28-13-generic (buildd@vernadsky) (gcc version
> 4.3.3 (Ubuntu 4.3.3-5ubuntu4) ) #45-Ubuntu SMP Tue Jun 30 19:49:51 UTC 2009
> scanModem update of: 2009_07_17
>
> There are no blacklisted modem drivers in /etc/modprobe* files
> Potentially useful modem drivers now loaded are:
> snd_hda_intel
> Attached USB devices are:
> ID 1058:0704 Western Digital Technologies, Inc.
> ID 05ca:1836 Ricoh Co., Ltd
> ID 04d9:1603 Holtek Semiconductor, Inc.
> ID 15ca:00c3 Textech International Ltd. Mini Optical Mouse
> If a cellphone is not detected, see
> http://ubuntuforums.org/archive/index.php/t-878554.html
> A sample report is:
> http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html
>
> If a USB modem or cellphone is attached and was not detected, please
> provide available information in your request to discuss@xxxxxxxxxxxxx
>
> For candidate card in slot 00:1b.0, firmware information and bootup
> diagnostics are:
> PCI slot PCI ID SubsystemID Name
> ---------- --------- --------- --------------
> 00:1b.0 8086:27d8 104d:81ef Audio device: Intel Corporation 82801G
>
> Modem interrupt assignment and sharing:
> 22: 474142 0 IO-APIC-fasteoi HDA Intel
> --- Bootup diagnostics for card in PCI slot 00:1b.0 ----
> [ 0.500340] pci 0000:00:1b.0: reg 10 64bit mmio: [0xd2300000-0xd2303fff]
> [ 0.500382] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
> [ 0.500387] pci 0000:00:1b.0: PME# disabled
> [ 16.708263] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) ->
> IRQ 22
> [ 16.708316] HDA Intel 0000:00:1b.0: setting latency timer to 64
> [ 5875.585088] HDA Intel 0000:00:1b.0: PCI INT A disabled
> [ 5876.604097] HDA Intel 0000:00:1b.0: restoring config space at offset 0x1
> (was 0x100006, writing 0x100002)
> [ 5876.604129] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) ->
> IRQ 22
> [ 5876.604139] HDA Intel 0000:00:1b.0: setting latency timer to 64
>
> The PCI slot 00:1b.0 of the modem card may be disabled early in
> a bootup process, but then enabled later. If modem drivers load
> but the modem is not responsive, read DOCs/Bootup.txt about possible fixes.
> Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
> if help is needed.
>
>
>
> ===== Advanced Linux Sound Architecture (ALSA) diagnostics =====
> The ALSA packages provide audio support and also drivers for some modems.
> ALSA diagnostics are written during bootup to /proc/asound/ folders.
>
> The ALSA verion is 1.0.18
> The modem cards detected by "aplay -l" are: None
>
>
> The /proc/asound/pcm file reports:
> -----------------------
> 00-00: STAC92xx Analog : STAC92xx Analog : playback 1 : capture 1
>
> about /proc/asound/cards:
> ------------------------
> 0 [Intel ]: HDA-Intel - HDA Intel
> HDA Intel at 0xd2300000 irq 22
>
> PCI slot 00:1b.0 has a High Definition Audio Card
> The drivers are in the kernel modules tree at:
> /lib/modules/2.6.28-13-generic/kernel/sound/pci/hda/snd-hda-intel.ko
> /lib/modules/2.6.28-11-generic/kernel/sound/pci/hda/snd-hda-intel.ko
> The modem codec file for the HDA card is: /proc/asound/card0/codec#1
> --------------------------------------------------------
> Codec: Conexant ID 2bfa
> Address: 1
> Vendor Id: 0x14f12bfa
> Subsystem Id: 0x104d0200
> Revision Id: 0x90000
> Modem Function Group: 0x2
>
> The audio card hosts a softmodem chip: 0x14f12bfa
>
> 14f1 is the Conexant Vendor ID, and 0x14f12bfa a softmodem chipset.
> Get a hsfmodem package through http://www.linuxant.com
>
> If not a Conexant modem, the driver hsfmodem-drivers with its dependent
> drivers:
>
> ----------
> provide audio + modem support with the modem chip residing on the subsystem.
> Any particular card can host any one of several soft modem chips.
>
> === Finished firmware and bootup diagnostics, next deducing cogent software.
> ===
>
> Predictive diagnostics for card in bus 00:1b.0:
> Modem chipset detected on
> NAME="Audio device: Intel Corporation 82801G "
> CLASS=0403
> PCIDEV=8086:27d8
> SUBSYS=104d:81ef
> IRQ=22
> HDA=8086:27d8
> SOFT=8086:27d8.HDA
> HDAchipVendorID=14f1
> CHIP=0x14f12bfa
> CodecClass=14f1
> IDENT=hsfmodem
> Driver=hsfmodem-drivers
>
> For candidate modem in: 00:1b.0
> 0403 Audio device: Intel Corporation 82801G
> Primary device ID: 8086:27d8
> Subsystem PCI_id 104d:81ef
> Softmodem codec or chipset from diagnostics: 0x14f12bfa
> from Archives:
> The HDA card softmodem chip is 0x14f12bfa
>
> Support type needed or chipset: hsfmodem
>
>
> Writing DOCs/Intel.txt
>
> For owners of a Dell PCs with Conexant HSF modems, a driver source package
> with full speed enabled is available, but requires driver compiling. Read
> DOCs/Conexant.txt
>
> From http://www.linuxant.com/drivers/hsf/full/downloads-ubuntu-x86.php
> download hsfmodem-7.80.02.02full_k2.6.28_13_generic_ubuntu_i386.deb.zip
> Under Linux unpack with:
> $ unzip hsfmodem*.zip
> Then install with:
> $ sudo dpkg -i hsfmodem*.deb
> Subsequently, the modem should be found with
> $ sudo wvdialconf /etc/wvdial.conf
> Edit in your personal information with:
> $ sudo gedit /etc/wvdial.conf
> and try dialing out with:
> $ sudo wvdial.
> See DOCs/Testing.txt for details.
>
> The directions following below need only be pursued, if the above procedures
> are not adequate.
>
> Start at http://www.linuxant.com/drivers/hsf/downloads-license.php to find
> the
> hsfmodem package matching your System. For several Linux distros, there are
> precompiled drivers matched to specific kernels. These have within the
> FileName,
> your KernelVersion: 2.6.28_13_generic
> They can be found through
> http://www.linuxant.com/drivers/hsf/full/downloads.php
> A more precise location may be given a few paragraphs below.
> If an EXACT Match with your your KernelVersion is not found, one of the
> "Generic packages with source" near the bottom of the page must be used.
> Downloaded packages must be moved into the Linux partition (home folder is
> OK)
> and unzipped with:
> unzip hsf*.zip
> The installation command for a .deb suffic packages is, with root/adm
> permission:
> sudo dpkg -i hsf*.deb
> while for .rpm suffix it is, with:
> rpm -i hsf*.rpm
>
> Support for Conexant chips hosted on High Definition Audio cards may require
> installation of additional packages, one of the alsa-driver-linuxant
> packages
> on http://www.linuxant.com/alsa-driver/ At the same time download the
> alsa-driver-1.0.17-1.patch , in case it prove to be later needed. During the
> hsfmodem install, there will be a message if there is necessary installation
> of
> alsa-driver-linuxant
>
> The installation command for a .deb suffic packages is, with root/adm
> permission:
> sudo dpkg -i hsf*.deb
> while for .rpm suffix it is, with:
> rpm -i hsf*.rpm
>
> There may a message that "Dependencies" are not satisfied. In this case the
> Ubuntu/Debian packages to be installed are linux-libc-dev & libc6-dev.
> Package
> names may be different for other Linuxes. If not on your install CD, these
> packages can be searched for at http://packages.ubuntu.com. After download,
> they can be coinstalled with:
> sudo dpkg -i li*.deb
> Again try the alsa-driver-linuxant
>
> There may be a message that the patch must be applied. In this case get the
> ftp://ftp.alsa-project.org/pub/driver/alsa-driver-1.0.17.tar.bz2
> Under Linux, this package is unpacked with:
> $ tar jxf alsa*.tar.bz2
> Next the patch is applied with:
> $ patch -p0 < alsa-driver-1.0.17-1.patch
>
> See http://linmodems.technion.ac.il/bigarch/archive-eighth/msg00838.html
> for details on compiling and installing replacement snd-hda-intel + its
> dependent drivers.
> After the installation is completed, rerun the hsfmodem installation.
> Reboot and try to detect the modem with Root permission:
> sudo wvdialconf /etc/wvdial.conf
>
> Read DOCs/Conexant.txt
>
> Writing DOCs/Conexant.txt
>
>
> Completed candidate modem analyses.
>
> The base of the UDEV device file system is: /dev/.udev
>
> Versions adequately match for the compiler installed: 4.3.3
> and the compiler used in kernel assembly: 4.3.3
>
>
>
> Minimal compiling resources appear complete:
> make utility - /usr/bin/make
> Compiler version 4.3
> linuc_headers base folder /lib/modules/2.6.28-13-generic/build
>
> However some compilations and executable functions may need additional
> files,
> in the FileNames.h (so called kernel "h"eaders) collection installed in
> /usr/include/ .
> For martian_modem, additional required packages are needed. The also
> required headers of package libc6 are commonly installed by default.
> Compiling hsfmodem drivers does require linux-libc-dev and libc6-dev
> packages, for kernels 2.6.24 and later versions.
> In not included on your install CD, search for them at
> http://packages.ubuntu.com
> or comparable Repository for other Linux distros.
> When compiling ALSA drivers, the utility "patch" will also be needed.
>
>
>
>
> If a driver compilation fails, with message including some lack of some
> FileName.h (stdio.h for example), then
> Some additional kernel-header files need installation to /usr/include. The
> minimal additional packages are libc6-dev
> and any of its dependents, under Ubuntu linux-libc-dev
>
> If an alternate ethernet connection is available,
> $ apt-get update
> $ apt-get -s install linux-kernel-devel
> will install needed packages.
> For Debian/Ubuntu related distributions, run the following command to
> display the needed package list:
>
> Otherwise packages have to be found through http://packages.ubuntu.com
> Once downloaded and transferred into a Linux partition,
> they can be installed alltogether with:
> $ sudo dpkg -i *.deb
>
> Checking settings of: /etc/ppp/options
> asyncmap 0
> noauth
> crtscts
> lock
> hide-password
> modem
> proxyarp
> lcp-echo-interval 30
> lcp-echo-failure 4
> noipx
>
> In case of a message like:
> Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
> see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
>
> Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0 eth1
> ppp0
> Which can interfere with Browser naviagation.
>
> Don't worry about the following, it is for experts should trouble shooting
> be necessary.
> ==========================================================
>
> Checking for modem support lines:
> --------------------------------------
> /device/modem symbolic link: slmodemd created symbolic link
> /dev/ttySL0: Within /etc/udev/ files:
>
> Within /etc/modprobe.conf files:
> /etc/modprobe.d/blacklist-modem.conf:# Uncomment these entries in order to
> blacklist unwanted modem drivers
> /etc/modprobe.d/blacklist-modem.conf:# blacklist snd-atiixp-modem
> /etc/modprobe.d/blacklist-modem.conf:# blacklist snd-via82xx-modem
> /etc/modprobe.d/alsa-base.conf:options snd-atiixp-modem index=-2
> /etc/modprobe.d/alsa-base.conf:options snd-via82xx-modem index=-2
> Within any ancient /etc/devfs files:
>
> Within ancient kernel 2.4.n /etc/module.conf files:
>
> --------- end modem support lines --------
>
>
>
