----- Original Message -----
From: <john31608@xxxxxxxxxx>
To: "Marvin Stodolsky" <marvin.stodolsky@xxxxxxxxx>
Cc: "Antonio" <olivares14031@xxxxxxxxx>
Sent: Monday, August 17, 2009 12:24 AM
Subject: Re: Fw: John Williams USA kernel 2.6.28-11.42-generic
Marv;
I used gedit to change Modem= /dev/modem to Modem= /dev/ttyAGS3and saved
it to /etc. Then sudo wvdial gives "Cannot open /dev/ttyAGS3 : No such
file or directory .
Antonio requested the following:
dadisboss@MARVIN:~$ sudo lsmod | grep 'agr*'
[sudo] password for dadisboss:
snd_page_alloc 16904 2 snd_hda_intel,snd_pcm
usb_storage 82880 2
dadisboss@MARVIN:~$ ls -l /dev/modem
ls: cannot access /dev/modem: No such file or directory
dadisboss@MARVIN:~$ dmesg | grep 'agr*'
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==>
[0000000000 - 0000001000]
[ 0.000000] On node 0 totalpages: 654975
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1736 pages used for memmap
[ 0.000000] Normal zone: 220470 pages, LIFO batch:31
[ 0.000000] HighMem zone: 3350 pages used for memmap
[ 0.000000] HighMem zone: 425436 pages, LIFO batch:31
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 649857
[ 0.004000] allocated 13101440 bytes of page_cgroup
[ 0.696019] Bluetooth: HCI device and connection manager initialized
[ 0.768141] checking if image is initramfs... it is
[ 1.270724] highmem bounce pool size: 64 pages
[ 1.270728] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.676024] ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum
part
[ 5.753910] Magic number: 5:684:605
[ 6.172825] Initializing USB Mass Storage driver...
[ 6.173287] scsi7 : SCSI emulation for USB Mass Storage devices
[ 6.185022] usb-storage: device found at 2
[ 6.185024] usb-storage: waiting for device to settle before scanning
[ 6.185032] usbcore: registered new interface driver usb-storage
[ 6.185037] USB Mass Storage support registered.
[ 6.614687] PM: Checking hibernation image.
[ 6.863135] scsi8 : SCSI emulation for USB Mass Storage devices
[ 6.863199] usb-storage: device found at 2
[ 6.863201] usb-storage: waiting for device to settle before scanning
[ 11.184190] usb-storage: device scan complete
[ 11.861122] usb-storage: device scan complete
[ 14.022745] type=1505 audit(1250480009.767:5): operation="profile_load"
name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default"
pid=2234
dadisboss@MARVIN:~$
Yours truly, John W
----- Original Message -----
From: "Marvin Stodolsky" <marvin.stodolsky@xxxxxxxxx>
To: <john31608@xxxxxxxxxx>
Cc: <Discuss@xxxxxxxxxxxxx>
Sent: Sunday, August 16, 2009 2:58 PM
Subject: Re: Fw: John Williams USA kernel 2.6.28-11.42-generic
John
In wvdial.conf, for agrsm driver modems, put in /dev/ttyAGS3
/dev/modem is a symbolic link most appropriate to old serial card modems
MarvS
On Sun, Aug 16, 2009 at 2:06 PM, Antonio
Olivares<olivares14031@xxxxxxxxx> wrote:
John,
Would you mind posting the following if you don't mind:
$ sudo lsmod | grep 'agr*'
$ ls -l /dev/modem
$ dmesg | grep 'agr*'
Thanks,
Antonio
On 8/16/09, john31608@xxxxxxxxxx <john31608@xxxxxxxxxx> wrote:
Antonio;
After following your furrther instructions sudo wvdialconf
/etc/wvdial.conf
gives "Scanning your serial ports for a modem...Failed...giving up". I
then
edited the wvdial.conf file using your template and my own particulars
and
saved it. sudo wvdial then gives "cannot open /dev/modem: no such file
or
directory". Thanks for giving me your time. John W
----- Original Message -----
From: "Antonio Olivares" <olivares14031@xxxxxxxxx>
To: <john31608@xxxxxxxxxx>
Cc: <Discuss@xxxxxxxxxxxxx>
Sent: Saturday, August 15, 2009 1:46 PM
Subject: Re: Fw: John Williams USA kernel 2.6.28-11.42-generic
John,
Sorry I did not read your message carefully. Apparently you have done
all of the above in the previous email. You have done the following
too?
$ sudo modprobe agrmodem
$ sudo modprobe agrserial
$ sudo ln -s /dev/ttyAGS3 /dev/ttySAGR
$ sudo ln -s /dev/ttyAGS3 /dev/modem
$ sudo wvdialconf /etc/wvdial.conf
and the last command does not find the modem? Then maybe you can try
a wvdial.conf file with the /dev/modem as the port and try to dialout?
See following wvdail.conf file, and adjust username, password, and
phone number to dialout and please report back
[Dialer Defaults]
Modem = /dev/modem
Baud = 57600
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2
Init3 =
Area Code =
Phone = 11111111111111
Username =1111111@xxxxxxxxxxxxx
Password =11111
Ask Password = 0
Dial Command = ATDT
Stupid Mode = 1
Compuserve = 0
Force Address =
Idle Seconds = 300
DialMessage1 =
DialMessage2 =
ISDN = 0
# Auto DNS = 1
Regards,
Antonio
On 8/15/09, Antonio Olivares <olivares14031@xxxxxxxxx> wrote:
John,
scanModem reports thayt you need agrsm-20090418.tar.gz
Download it from
http://linmodems.technion.ac.il/packages/ltmodem/11c11040/agrsm-20090418.tar.gz
extract it with
$ tar -zxvf agrsm-20090418.tar.gz
$ cd agrsm-20090418/
$ make all
$ sudo make install
Please read the instructions provided in Agrsm.txt.
Predictive diagnostics for card in bus 04:07.0:
Modem chipset detected on
NAME="Communication controller: Agere Systems Device 0620"
CLASS=0780
PCIDEV=11c1:0620
SUBSYS=11c1:0620
IRQ=11
IDENT=agrsm
For candidate modem in: 04:07.0
0780 Communication controller: Agere Systems Device 0620
Primary device ID: 11c1:0620
Support type needed or chipset: agrsm
The AgereSystems/LSI agrsm code supports compiling of a agrmodem +
agrsm driver pair.
One resource site is
http://linmodems.technion.ac.il/packages/ltmodem/11c11040/
Thereat get the agrsm_howto.txt and one of the agrsm-tools packages.
The initial agrsm_howto.txt compiling steps are only cogent to modems
with PCI IDs:
11c1:0620, 11c1:048c and 11c1:048f chips.
They use the agrsm-20090418.tar.gz package.
The agrsm-tools sets a useful symbolic link and a agrsm-test utlity
For AgereSystems/LSI with Vendor 11c1 chips hosted on High Definition
Audio cards, there may be support
through the agrsm resources (providing an agrmodem + agrserial driver
pair) as an alternative to usage
of the snd-hda-intel driver + slmodemd helper. For the 11c11040 modem
chip, ONLY the agrsm code is competent.
Your Linux distro's dkms package should be first installed, as it
directs the installation of modem
specific dkms-agrsm resources, and also directs auto-installation of
new drivers upon kernel upgrades.
Currently, the dkms-agrsm code is NOT competent for 2.6.28 and later
kernels.
A short term fix is to install linux-image + linux-headers packages
for earlier kernels.
For detailed instructions for Ubuntu Jaunty with 2.6.28 kernels, see
http://linmodems.technion.ac.il/bigarch/archive-nineth/msg01316.html
The primary dkms-agrsm resource site is
http://linux.zsolttech.com/linmodem/agrsm/
whereat a few different packaging types are available. Debian type
installers (supporting Ubuntu too)
are copied to
http://linmodems.technion.ac.il/packages/ltmodem/11c11040/
. Thereat the current package
is the dkms-agrsm_2.1.80-6_i386.deb is for Agere/LSI chipsets hosted
on High Definition Audio cards.
Read the Modem/DOCs/Agrsm.txt for details.
Regards,
Antonio
On 8/15/09, john31608@xxxxxxxxxx <john31608@xxxxxxxxxx> wrote:
----- Original Message -----
From: <john31608@xxxxxxxxxx>
To: <discuss-subscribe@xxxxxxxxxxxxx>
Sent: Saturday, August 15, 2009 1:31 AM
Subject: John Williams USA kernel 2.6.28-11.42-generic
This is for the Agere SV92PP modem card. I tried the recommended
package
agrsm-20090418.tar.gz. I also tried dkms-agrsm_2.1.80-7_i386.deb
with
kernel-image-2.6.27-11-generic-di_2.6.27-11.31_i386.udeb also
linux-headers-2.6.27-11-generic_2.6.27-11.31_i386.deb and
linux-headers-2.6.27-11_2.6.27-11.31_all.deb. In either case the
agrserial
and agrmodem drivers appear to load but wvdialconf gives "Sorry, no
modem
was detected..." Is this worth pursuing or should I save myself the
headaches and just shell out for the US Robotics modem at Wal-Mart?
I
am
brand new to Linux on a 500 GB dual boot hard drive so I'm
definitely
just
learning as I go. I send along the ModemData and the dmesg.txt.
Yours
truly, John Williams
