Hi, my laptop has a "potentially" modem, because it is disabled during
the boot(correct?)
I'm a linux-beginner: i can't understand if the producer is intel or conexant,
and in any case in which manner I can enable my modem.
Thanks
Marco
ModemData:
-------------------------- System information ----------------------------
CPU=i686,
Linux version 2.6.27-14-generic (buildd@rothera) (gcc version 4.3.2
(Ubuntu 4.3.2-1ubuntu11) ) #1 SMP Tue Jun 30 19:57:39 UTC 2009
scanModem update of: 2009_07_17
There are no blacklisted modem drivers in /etc/modprobe* files
Potentially useful modem drivers now loaded are:
snd_hda_intel
Attached USB devices are:
ID 05ca:1870 Ricoh Co., Ltd Webcam 1000
ID 0a81:0101 Chesen Electronics Corp. Keyboard
If a cellphone is not detected, see
http://ubuntuforums.org/archive/index.php/t-878554.html
A sample report is:
http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html
If a USB modem or cellphone is attached and was not detected, please
provide available information in your request to discuss@xxxxxxxxxxxxx
For candidate card in slot 00:1b.0, firmware information and bootup
diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
00:1b.0 8086:27d8 103c:30bb Audio device: Intel Corporation 82801G
Modem interrupt assignment and sharing:
22: 682 0 IO-APIC-fasteoi HDA Intel
--- Bootup diagnostics for card in PCI slot 00:1b.0 ----
[ 0.608424] PCI: 0000:00:1b.0 reg 10 64bit mmio: [d8240000, d8243fff]
[ 0.608424] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.608424] pci 0000:00:1b.0: PME# disabled
[ 0.628773] pci 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 14.038131] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level,
low) -> IRQ 22
[ 14.038167] HDA Intel 0000:00:1b.0: setting latency timer to 64
The PCI slot 00:1b.0 of the modem card may be disabled early in
a bootup process, but then enabled later. If modem drivers load
but the modem is not responsive, read DOCs/Bootup.txt about possible fixes.
Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
if help is needed.
===== Advanced Linux Sound Architecture (ALSA) diagnostics =====
The ALSA packages provide audio support and also drivers for some modems.
ALSA diagnostics are written during bootup to /proc/asound/ folders.
The ALSA verion is 1.0.17
The modem cards detected by "aplay -l" are: None
The /proc/asound/pcm file reports:
-----------------------
00-01: Conexant Digital : Conexant Digital : playback 1
00-00: CONEXANT Analog : CONEXANT Analog : playback 1 : capture 1
about /proc/asound/cards:
------------------------
0 [Intel ]: HDA-Intel - HDA Intel
HDA Intel at 0xd8240000 irq 22
PCI slot 00:1b.0 has a High Definition Audio Card
The drivers are in the kernel modules tree at:
/lib/modules/2.6.27-11-generic/kernel/sound/pci/hda/snd-hda-intel.ko
/lib/modules/2.6.27-14-generic/kernel/sound/pci/hda/snd-hda-intel.ko
/lib/modules/2.6.27-7-generic/kernel/sound/pci/hda/snd-hda-intel.ko
UNEXPECTED HDA diagnostic outcome.
=== Finished firmware and bootup diagnostics, next deducing cogent software. ===
Predictive diagnostics for card in bus 00:1b.0:
Modem chipset detected on
NAME="Audio device: Intel Corporation 82801G "
CLASS=0403
PCIDEV=8086:27d8
SUBSYS=103c:30bb
IRQ=22
HDA=8086:27d8
SOFT=8086:27d8.HDA
ArchivedChip=0x14f12bfa
CodecClass=14f1
IDENT=hsfmodem
Driver=hsfmodem-drivers
For candidate modem in: 00:1b.0
0403 Audio device: Intel Corporation 82801G
Primary device ID: 8086:27d8
Subsystem PCI_id 103c:30bb
Softmodem codec or chipset from diagnostics:
from Archives: 0x14f12bfa
Support type needed or chipset: hsfmodem
Writing DOCs/Intel.txt
For owners of a Dell PCs with Conexant HSF modems, a driver source
package with full speed enabled is available, but requires driver
compiling. Read DOCs/Conexant.txt
From http://www.linuxant.com/drivers/hsf/full/downloads-ubuntu-x86.php
download hsfmodem-7.80.02.02full_k2.6.27_14_generic_ubuntu_i386.deb.zip
Under Linux unpack with:
$ unzip hsfmodem*.zip
Then install with:
$ sudo dpkg -i hsfmodem*.deb
Subsequently, the modem should be found with
$ sudo wvdialconf /etc/wvdial.conf
Edit in your personal information with:
$ sudo gedit /etc/wvdial.conf
and try dialing out with:
$ sudo wvdial.
See DOCs/Testing.txt for details.
The directions following below need only be pursued, if the above
procedures are not adequate.
Start at http://www.linuxant.com/drivers/hsf/downloads-license.php to find the
hsfmodem package matching your System. For several Linux distros, there are
precompiled drivers matched to specific kernels. These have within the FileName,
your KernelVersion: 2.6.27_14_generic
They can be found through
http://www.linuxant.com/drivers/hsf/full/downloads.php
A more precise location may be given a few paragraphs below.
If an EXACT Match with your your KernelVersion is not found, one of the
"Generic packages with source" near the bottom of the page must be used.
Downloaded packages must be moved into the Linux partition (home folder is OK)
and unzipped with:
unzip hsf*.zip
The installation command for a .deb suffic packages is, with root/adm
permission:
sudo dpkg -i hsf*.deb
while for .rpm suffix it is, with:
rpm -i hsf*.rpm
Support for Conexant chips hosted on High Definition Audio cards may require
installation of additional packages, one of the alsa-driver-linuxant packages
on http://www.linuxant.com/alsa-driver/ At the same time download the
alsa-driver-1.0.17-1.patch , in case it prove to be later needed. During the
hsfmodem install, there will be a message if there is necessary installation of
alsa-driver-linuxant
The installation command for a .deb suffic packages is, with root/adm
permission:
sudo dpkg -i hsf*.deb
while for .rpm suffix it is, with:
rpm -i hsf*.rpm
There may a message that "Dependencies" are not satisfied. In this
case the Ubuntu/Debian packages to be installed are linux-libc-dev &
libc6-dev. Package
names may be different for other Linuxes. If not on your install CD, these
packages can be searched for at http://packages.ubuntu.com. After download,
they can be coinstalled with:
sudo dpkg -i li*.deb
Again try the alsa-driver-linuxant
There may be a message that the patch must be applied. In this case get the
ftp://ftp.alsa-project.org/pub/driver/alsa-driver-1.0.17.tar.bz2
Under Linux, this package is unpacked with:
$ tar jxf alsa*.tar.bz2
Next the patch is applied with:
$ patch -p0 < alsa-driver-1.0.17-1.patch
See http://linmodems.technion.ac.il/bigarch/archive-eighth/msg00838.html
for details on compiling and installing replacement snd-hda-intel + its
dependent drivers.
After the installation is completed, rerun the hsfmodem installation.
Reboot and try to detect the modem with Root permission:
sudo wvdialconf /etc/wvdial.conf
Read DOCs/Conexant.txt
Writing DOCs/Conexant.txt
Completed candidate modem analyses.
The base of the UDEV device file system is: /dev/.udev
Versions adequately match for the compiler installed: 4.3.2
and the compiler used in kernel assembly: 4.3.2
The patch utility is needed and is needed for compiling ALSA drivers,
and possibly others.
Minimal compiling resources appear complete:
make utility - /usr/bin/make
Compiler version 4.3
linuc_headers base folder /lib/modules/2.6.27-14-generic/build
However some compilations and executable functions may need additional files,
in the FileNames.h (so called kernel "h"eaders) collection installed
in /usr/include/ .
For martian_modem, additional required packages are needed. The also
required headers of package libc6 are commonly installed by default.
Compiling hsfmodem drivers does require linux-libc-dev and libc6-dev
packages, for kernels 2.6.24 and later versions.
In not included on your install CD, search for them at
http://packages.ubuntu.com
or comparable Repository for other Linux distros.
When compiling ALSA drivers, the utility "patch" will also be needed.
If a driver compilation fails, with message including some lack of
some FileName.h (stdio.h for example), then
Some additional kernel-header files need installation to /usr/include.
The minimal additional packages are libc6-dev
and any of its dependents, under Ubuntu linux-libc-dev
If an alternate ethernet connection is available,
$ apt-get update
$ apt-get -s install linux-kernel-devel
will install needed packages.
For Debian/Ubuntu related distributions, run the following command to
display the needed package list:
Otherwise packages have to be found through http://packages.ubuntu.com
Once downloaded and transferred into a Linux partition,
they can be installed alltogether with:
$ sudo dpkg -i *.deb
Checking pppd properties:
-rwsr-xr-- 1 root dip 277160 2008-11-20 21:58 /usr/sbin/pppd
In case of an "error 17" "serial loopback" problem, see:
http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html
To enable dialout without Root permission do:
$ su - root (not for Ubuntu)
sudo chmod a+x /usr/sbin/pppd
or under Ubuntu related Linuxes
sudo chmod a+x /usr/sbin/pppd
Checking settings of: /etc/ppp/options
asyncmap 0
noauth
crtscts
lock
hide-password
modem
proxyarp
lcp-echo-interval 30
lcp-echo-failure 4
noipx
In case of a message like:
Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0
wlan0 wmaster0
Which can interfere with Browser naviagation.
Don't worry about the following, it is for experts should trouble
shooting be necessary.
==========================================================
Checking for modem support lines:
--------------------------------------
/device/modem symbolic link:
slmodemd created symbolic link /dev/ttySL0:
Within /etc/udev/ files:
Within /etc/modprobe.conf files:
/etc/modprobe.d/alsa-base:options snd-atiixp-modem index=-2
/etc/modprobe.d/alsa-base:options snd-via82xx-modem index=-2
/etc/modprobe.d/blacklist-modem:# Uncomment these entries in order to
blacklist unwanted modem drivers
/etc/modprobe.d/blacklist-modem:# blacklist snd-atiixp-modem
/etc/modprobe.d/blacklist-modem:# blacklist snd-via82xx-modem
Within any ancient /etc/devfs files:
Within ancient kernel 2.4.n /etc/module.conf files:
--------- end modem support lines --------
dmesg
CPU0 CPU1
0: 15517 5 IO-APIC-edge timer
1: 138 0 IO-APIC-edge i8042
8: 28 0 IO-APIC-edge rtc0
9: 984 20 IO-APIC-fasteoi acpi
12: 8193 0 IO-APIC-edge i8042
14: 738 0 IO-APIC-edge ata_piix
15: 0 0 IO-APIC-edge ata_piix
16: 3 0 IO-APIC-fasteoi uhci_hcd:usb4,
ohci1394, i915@pci:0000:00:02.0
17: 0 0 IO-APIC-fasteoi mmc0
18: 0 0 IO-APIC-fasteoi uhci_hcd:usb3
19: 55 0 IO-APIC-fasteoi uhci_hcd:usb2
20: 54 0 IO-APIC-fasteoi eth0
22: 682 0 IO-APIC-fasteoi HDA Intel
23: 11 0 IO-APIC-fasteoi uhci_hcd:usb1, ehci_hcd:usb5
220: 197 0 PCI-MSI-edge iwl3945
221: 10652 0 PCI-MSI-edge ahci
NMI: 0 0 Non-maskable interrupts
LOC: 8648 13163 Local timer interrupts
RES: 4332 5893 Rescheduling interrupts
CAL: 76 28408 function call interrupts
TLB: 86 62 TLB shootdowns
SPU: 0 0 Spurious interrupts
ERR: 0
MIS: 0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.27-14-generic (buildd@rothera) (gcc
version 4.3.2 (Ubuntu 4.3.2-1ubuntu11) ) #1 SMP Tue Jun 30 19:57:39
UTC 2009 (Ubuntu 2.6.27-14.35-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003f670000 (usable)
[ 0.000000] BIOS-e820: 000000003f670000 - 000000003f700000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003f700000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] DMI present.
[ 0.000000] last_pfn = 0x3f670 max_arch_pfn = 0x100000
[ 0.000000] kernel direct mapping tables up to 38000000 @ 7000-c000
[ 0.000000] RAMDISK: 3781f000 - 37fefb1d
[ 0.000000] ACPI: RSDP 000F7DE0, 0014 (r0 HP )
[ 0.000000] ACPI: RSDT 3F67DEAB, 0044 (r1 HP 30BB 6040000
LTP 0)
[ 0.000000] ACPI: FACP 3F685DEE, 0074 (r1 HP 30BB 6040000
LOHR 5A)
[ 0.000000] ACPI: DSDT 3F67EACD, 7321 (r1 HP 30BB 6040000
MSFT 100000E)
[ 0.000000] ACPI: FACS 3F686FC0, 0040
[ 0.000000] ACPI: APIC 3F685E62, 0068 (r1 HP 30BB 6040000
LOHR 5A)
[ 0.000000] ACPI: HPET 3F685ECA, 0038 (r1 HP 30BB 6040000
LOHR 5A)
[ 0.000000] ACPI: MCFG 3F685F02, 003C (r1 HP 30BB 6040000
LOHR 5A)
[ 0.000000] ACPI: BOOT 3F685FD8, 0028 (r1 HP 30BB 6040000
LTP 1)
[ 0.000000] ACPI: APIC 3F685F70, 0068 (r1 HP 30BB 6040000
LTP 0)
[ 0.000000] ACPI: SSDT 3F67E8BF, 020A (r1 HP 30BB 1000
INTL 20050624)
[ 0.000000] ACPI: SSDT 3F67DEEF, 04F6 (r1 HP 30BB 3000
INTL 20050624)
[ 0.000000] ACPI: BIOS bug: multiple APIC/MADT found, using 0
[ 0.000000] ACPI: If "acpi_apic_instance=2" works better, notify
linux-acpi@xxxxxxxxxxxxxxx
[ 0.000000] ACPI: DMI detected: Hewlett-Packard
[ 0.000000] 118MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 38000000
[ 0.000000] low ram: 00000000 - 38000000
[ 0.000000] bootmap 00008000 - 0000f000
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 0038000000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==>
[0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==>
[0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==>
[0000006000 - 0000007000]
[ 0.000000] #3 [0000100000 - 00005c39e0] TEXT DATA BSS ==>
[0000100000 - 00005c39e0]
[ 0.000000] #4 [003781f000 - 0037fefb1d] RAMDISK ==>
[003781f000 - 0037fefb1d]
[ 0.000000] #5 [00005c4000 - 00005c7000] INIT_PG_TABLE ==>
[00005c4000 - 00005c7000]
[ 0.000000] #6 [000009f800 - 0000100000] BIOS reserved ==>
[000009f800 - 0000100000]
[ 0.000000] #7 [0000007000 - 0000008000] PGTABLE ==>
[0000007000 - 0000008000]
[ 0.000000] #8 [0000008000 - 000000f000] BOOTMAP ==>
[0000008000 - 000000f000]
[ 0.000000] found SMP MP-table at [c00f7e90] 000f7e90
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x00038000
[ 0.000000] HighMem 0x00038000 -> 0x0003f670
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x0003f670
[ 0.000000] On node 0 totalpages: 259599
[ 0.000000] free_area_init_node: node 0, pgdat c048c700,
node_mem_map c1000000
[ 0.000000] DMA zone: 3963 pages, LIFO batch:0
[ 0.000000] Normal zone: 223300 pages, LIFO batch:31
[ 0.000000] HighMem zone: 30053 pages, LIFO batch:7
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000dc000
[ 0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 50000000 (gap:
40000000:a0000000)
[ 0.000000] PERCPU: Allocating 41628 bytes of per cpu data
[ 0.000000] NR_CPUS: 64, nr_cpu_ids: 2, nr_node_ids 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 257316
[ 0.000000] Kernel command line:
root=UUID=afe06b69-cdc7-4b47-8995-cc241240ff64 ro quiet splash
pci=routeirq
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] TSC: PIT calibration confirmed by PMTIMER.
[ 0.000000] TSC: using PMTIMER calibration value
[ 0.000000] Detected 1596.470 MHz processor.
[ 0.004000] Console: colour VGA+ 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] Memory: 1015012k/1038784k available (2579k kernel code,
22968k reserved, 1162k data, 428k init, 121280k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xffc77000 - 0xfffff000 (3616 kB)
[ 0.004000] pkmap : 0xff400000 - 0xff800000 (4096 kB)
[ 0.004000] vmalloc : 0xf8800000 - 0xff3fe000 ( 107 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.004000] .init : 0xc04ad000 - 0xc0518000 ( 428 kB)
[ 0.004000] .data : 0xc0384caa - 0xc04a7680 (1162 kB)
[ 0.004000] .text : 0xc0100000 - 0xc0384caa (2579 kB)
[ 0.004000] Checking if this processor honours the WP bit even in
supervisor mode...Ok.
[ 0.004000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.004000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0,
CPUs=2, Nodes=1
[ 0.004000] hpet clockevent registered
[ 0.004000] Calibrating delay loop (skipped), value calculated
using timer frequency.. 3192.94 BogoMIPS (lpj=6385880)
[ 0.004000] Security Framework initialized
[ 0.004000] SELinux: Disabled at boot.
[ 0.004000] AppArmor: AppArmor initialized
[ 0.004000] Mount-cache hash table entries: 512
[ 0.004000] Initializing cgroup subsys ns
[ 0.004000] Initializing cgroup subsys cpuacct
[ 0.004000] Initializing cgroup subsys memory
[ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004000] CPU: L2 cache: 2048K
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 0
[ 0.004000] using mwait in idle threads.
[ 0.004000] Checking 'hlt' instruction... OK.
[ 0.018737] ACPI: Core revision 20080609
[ 0.021848] ACPI: Checking initramfs for custom DSDT
[ 0.456288] ENABLING IO-APIC IRQs
[ 0.456495] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.497444] CPU0: Intel Genuine Intel(R) CPU T2050 @
1.60GHz stepping 08
[ 0.500031] Booting processor 1/1 ip 6000
[ 0.004000] Initializing CPU#1
[ 0.004000] Calibrating delay using timer specific routine..
3192.96 BogoMIPS (lpj=6385939)
[ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004000] CPU: L2 cache: 2048K
[ 0.004000] CPU: Physical Processor ID: 0
[ 0.004000] CPU: Processor Core ID: 1
[ 0.584583] CPU1: Intel Genuine Intel(R) CPU T2050 @
1.60GHz stepping 08
[ 0.584610] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.588058] Brought up 2 CPUs
[ 0.588062] Total of 2 processors activated (6385.90 BogoMIPS).
[ 0.588090] CPU0 attaching sched-domain:
[ 0.588094] domain 0: span 0-1 level MC
[ 0.588097] groups: 0 1
[ 0.588105] CPU1 attaching sched-domain:
[ 0.588108] domain 0: span 0-1 level MC
[ 0.588111] groups: 1 0
[ 0.588248] net_namespace: 840 bytes
[ 0.588248] Booting paravirtualized kernel on bare hardware
[ 0.588381] Time: 20:01:05 Date: 07/30/09
[ 0.588418] NET: Registered protocol family 16
[ 0.588444] EISA bus registered
[ 0.588444] ACPI: bus type pci registered
[ 0.588444] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255
[ 0.588444] PCI: MCFG area at e0000000 reserved in E820
[ 0.588444] PCI: Using MMCONFIG for extended config space
[ 0.588444] PCI: Using configuration type 1 for base access
[ 0.592725] ACPI: EC: Look up EC in DSDT
[ 0.596541] ACPI: BIOS _OSI(Linux) query ignored via DMI
[ 0.597325] ACPI: Interpreter enabled
[ 0.597334] ACPI: (supports S0 S3 S4 S5)
[ 0.597345] ACPI: Using IOAPIC for interrupt routing
[ 0.597345] ACPI: EC: non-query interrupt received, switching to
interrupt mode
[ 0.608424] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 0.608424] ACPI: EC: driver started in interrupt mode
[ 0.608424] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.608424] PCI: 0000:00:02.0 reg 10 32bit mmio: [d8100000, d817ffff]
[ 0.608424] PCI: 0000:00:02.0 reg 14 io port: [1800, 1807]
[ 0.608424] PCI: 0000:00:02.0 reg 18 32bit mmio: [c0000000, cfffffff]
[ 0.608424] PCI: 0000:00:02.0 reg 1c 32bit mmio: [d8200000, d823ffff]
[ 0.608424] PCI: 0000:00:02.1 reg 10 32bit mmio: [d8180000, d81fffff]
[ 0.608424] PCI: 0000:00:1b.0 reg 10 64bit mmio: [d8240000, d8243fff]
[ 0.608424] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.608424] pci 0000:00:1b.0: PME# disabled
[ 0.608505] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.608511] pci 0000:00:1c.0: PME# disabled
[ 0.608608] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.608614] pci 0000:00:1c.1: PME# disabled
[ 0.608671] PCI: 0000:00:1d.0 reg 20 io port: [1820, 183f]
[ 0.608742] PCI: 0000:00:1d.1 reg 20 io port: [1840, 185f]
[ 0.608812] PCI: 0000:00:1d.2 reg 20 io port: [1860, 187f]
[ 0.608883] PCI: 0000:00:1d.3 reg 20 io port: [1880, 189f]
[ 0.608958] PCI: 0000:00:1d.7 reg 10 32bit mmio: [d8444000, d84443ff]
[ 0.609038] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.609045] pci 0000:00:1d.7: PME# disabled
[ 0.609225] pci 0000:00:1f.0: quirk: region 1000-107f claimed by
ICH6 ACPI/GPIO/TCO
[ 0.609231] pci 0000:00:1f.0: quirk: region 1180-11bf claimed by ICH6 GPIO
[ 0.609279] PCI: 0000:00:1f.1 reg 10 io port: [0, 7]
[ 0.609289] PCI: 0000:00:1f.1 reg 14 io port: [0, 3]
[ 0.609298] PCI: 0000:00:1f.1 reg 18 io port: [0, 7]
[ 0.609307] PCI: 0000:00:1f.1 reg 1c io port: [0, 3]
[ 0.609316] PCI: 0000:00:1f.1 reg 20 io port: [1810, 181f]
[ 0.609388] PCI: 0000:00:1f.2 reg 10 io port: [18d0, 18d7]
[ 0.609397] PCI: 0000:00:1f.2 reg 14 io port: [18c4, 18c7]
[ 0.609406] PCI: 0000:00:1f.2 reg 18 io port: [18c8, 18cf]
[ 0.609415] PCI: 0000:00:1f.2 reg 1c io port: [18c0, 18c3]
[ 0.609425] PCI: 0000:00:1f.2 reg 20 io port: [18b0, 18bf]
[ 0.609434] PCI: 0000:00:1f.2 reg 24 32bit mmio: [d8444400, d84447ff]
[ 0.609486] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.609492] pci 0000:00:1f.2: PME# disabled
[ 0.609552] PCI: 0000:00:1f.3 reg 20 io port: [18e0, 18ff]
[ 0.612084] PCI: 0000:02:00.0 reg 10 32bit mmio: [d6000000, d6000fff]
[ 0.612379] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 0.612393] pci 0000:02:00.0: PME# disabled
[ 0.612449] PCI: bridge 0000:00:1c.0 io port: [2000, 2fff]
[ 0.612456] PCI: bridge 0000:00:1c.0 32bit mmio: [d6000000, d7ffffff]
[ 0.612465] PCI: bridge 0000:00:1c.0 64bit mmio pref: [d2000000, d3ffffff]
[ 0.612531] PCI: bridge 0000:00:1c.1 io port: [3000, 3fff]
[ 0.612537] PCI: bridge 0000:00:1c.1 32bit mmio: [d4000000, d5ffffff]
[ 0.612547] PCI: bridge 0000:00:1c.1 64bit mmio pref: [d0000000, d1ffffff]
[ 0.612604] PCI: 0000:05:05.0 reg 10 32bit mmio: [d8001000, d80017ff]
[ 0.612677] pci 0000:05:05.0: supports D1
[ 0.612680] pci 0000:05:05.0: supports D2
[ 0.612683] pci 0000:05:05.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.612689] pci 0000:05:05.0: PME# disabled
[ 0.612732] PCI: 0000:05:05.1 reg 10 32bit mmio: [d8001800, d80018ff]
[ 0.612806] pci 0000:05:05.1: supports D1
[ 0.612809] pci 0000:05:05.1: supports D2
[ 0.612812] pci 0000:05:05.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.612818] pci 0000:05:05.1: PME# disabled
[ 0.612858] PCI: 0000:05:05.2 reg 10 32bit mmio: [d8001c00, d8001cff]
[ 0.612932] pci 0000:05:05.2: supports D1
[ 0.612935] pci 0000:05:05.2: supports D2
[ 0.612938] pci 0000:05:05.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.612944] pci 0000:05:05.2: PME# disabled
[ 0.612984] PCI: 0000:05:05.3 reg 10 32bit mmio: [d8002000, d80020ff]
[ 0.613057] pci 0000:05:05.3: supports D1
[ 0.613059] pci 0000:05:05.3: supports D2
[ 0.613062] pci 0000:05:05.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.613068] pci 0000:05:05.3: PME# disabled
[ 0.613108] PCI: 0000:05:05.4 reg 10 32bit mmio: [d8002400, d80024ff]
[ 0.613181] pci 0000:05:05.4: supports D1
[ 0.613184] pci 0000:05:05.4: supports D2
[ 0.613186] pci 0000:05:05.4: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.613193] pci 0000:05:05.4: PME# disabled
[ 0.613240] PCI: 0000:05:08.0 reg 10 32bit mmio: [d8000000, d8000fff]
[ 0.613250] PCI: 0000:05:08.0 reg 14 io port: [4000, 403f]
[ 0.613314] pci 0000:05:08.0: supports D1
[ 0.613316] pci 0000:05:08.0: supports D2
[ 0.613319] pci 0000:05:08.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.613325] pci 0000:05:08.0: PME# disabled
[ 0.613374] pci 0000:00:1e.0: transparent bridge
[ 0.613380] PCI: bridge 0000:00:1e.0 io port: [4000, 4fff]
[ 0.613386] PCI: bridge 0000:00:1e.0 32bit mmio: [d8000000, d80fffff]
[ 0.613416] bus 00 -> node 0
[ 0.613426] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.613961] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.614164] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.614381] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.624201] ACPI: PCI Interrupt Link [LNKA] (IRQs *11)
[ 0.624397] ACPI: PCI Interrupt Link [LNKB] (IRQs *3)
[ 0.624591] ACPI: PCI Interrupt Link [LNKC] (IRQs *3)
[ 0.624783] ACPI: PCI Interrupt Link [LNKD] (IRQs *4)
[ 0.624976] ACPI: PCI Interrupt Link [LNKE] (IRQs *10)
[ 0.625167] ACPI: PCI Interrupt Link [LNKF] (IRQs 11) *0, disabled.
[ 0.625363] ACPI: PCI Interrupt Link [LNKG] (IRQs *5)
[ 0.625555] ACPI: PCI Interrupt Link [LNKH] (IRQs *7)
[ 0.625642] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.625642] pnp: PnP ACPI init
[ 0.625642] ACPI: bus type pnp registered
[ 0.628773] pnp: PnP ACPI: found 10 devices
[ 0.628773] ACPI: ACPI bus type pnp unregistered
[ 0.628773] PnPBIOS: Disabled by ACPI PNP
[ 0.628773] PCI: Using ACPI for IRQ routing
[ 0.628773] PCI: Routing PCI interrupts for all devices because
"pci=routeirq" specified
[ 0.628773] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.628773] pci 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[ 0.628773] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.628773] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.628773] pci 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.628773] pci 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.628773] pci 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 0.628773] pci 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 0.628773] pci 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 0.628773] pci 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 0.628773] pci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.628773] pci 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 0.628773] pci 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.628773] pci 0000:05:05.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 0.628773] pci 0000:05:05.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.628773] pci 0000:05:05.2: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.628773] pci 0000:05:05.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.628773] pci 0000:05:05.4: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[ 0.628773] pci 0000:05:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 0.636044] NET: Registered protocol family 8
[ 0.636047] NET: Registered protocol family 20
[ 0.636069] NetLabel: Initializing
[ 0.636069] NetLabel: domain hash size = 128
[ 0.636069] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.636083] NetLabel: unlabeled traffic allowed by default
[ 0.636093] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.636099] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.637782] tracer: 772 pages allocated for 65536 entries of 48 bytes
[ 0.637786] actual entries 65620
[ 0.637894] AppArmor: AppArmor Filesystem Enabled
[ 0.637923] ACPI: RTC can wake from S4
[ 0.640045] Switched to high resolution mode on CPU 0
[ 0.640634] Switched to high resolution mode on CPU 1
[ 0.644028] system 00:01: iomem range 0xe0000000-0xefffffff could
not be reserved
[ 0.644033] system 00:01: iomem range 0xfed14000-0xfed17fff could
not be reserved
[ 0.644037] system 00:01: iomem range 0xfed18000-0xfed18fff could
not be reserved
[ 0.644042] system 00:01: iomem range 0xfed19000-0xfed19fff could
not be reserved
[ 0.644046] system 00:01: iomem range 0xfed1c000-0xfed1ffff could
not be reserved
[ 0.644050] system 00:01: iomem range 0xfed20000-0xfed3ffff could
not be reserved
[ 0.644054] system 00:01: iomem range 0xfed40000-0xfed44fff could
not be reserved
[ 0.644059] system 00:01: iomem range 0xfed45000-0xfed8ffff could
not be reserved
[ 0.644068] system 00:03: iomem range 0xfed00000-0xfed003ff could
not be reserved
[ 0.644079] system 00:05: ioport range 0x380-0x383 has been reserved
[ 0.644083] system 00:05: ioport range 0x680-0x69f has been reserved
[ 0.644087] system 00:05: ioport range 0x800-0x80f has been reserved
[ 0.644091] system 00:05: ioport range 0x1000-0x107f has been reserved
[ 0.644095] system 00:05: ioport range 0x1180-0x11bf has been reserved
[ 0.644099] system 00:05: ioport range 0x1640-0x164f has been reserved
[ 0.644110] system 00:06: ioport range 0x6a0-0x6af has been reserved
[ 0.644114] system 00:06: ioport range 0x6b0-0x6ff has been reserved
[ 0.679494] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[ 0.679499] pci 0000:00:1c.0: IO window: 0x2000-0x2fff
[ 0.679508] pci 0000:00:1c.0: MEM window: 0xd6000000-0xd7ffffff
[ 0.679514] pci 0000:00:1c.0: PREFETCH window:
0x000000d2000000-0x000000d3ffffff
[ 0.679524] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
[ 0.679529] pci 0000:00:1c.1: IO window: 0x3000-0x3fff
[ 0.679537] pci 0000:00:1c.1: MEM window: 0xd4000000-0xd5ffffff
[ 0.679543] pci 0000:00:1c.1: PREFETCH window:
0x000000d0000000-0x000000d1ffffff
[ 0.679553] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
[ 0.679558] pci 0000:00:1e.0: IO window: 0x4000-0x4fff
[ 0.679566] pci 0000:00:1e.0: MEM window: 0xd8000000-0xd80fffff
[ 0.679572] pci 0000:00:1e.0: PREFETCH window: disabled
[ 0.679590] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 0.679597] pci 0000:00:1c.0: setting latency timer to 64
[ 0.679608] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16
[ 0.679614] pci 0000:00:1c.1: setting latency timer to 64
[ 0.679622] pci 0000:00:1e.0: enabling device (0004 -> 0007)
[ 0.679629] pci 0000:00:1e.0: setting latency timer to 64
[ 0.679635] bus: 00 index 0 io port: [0, ffff]
[ 0.679638] bus: 00 index 1 mmio: [0, ffffffff]
[ 0.679641] bus: 02 index 0 io port: [2000, 2fff]
[ 0.679644] bus: 02 index 1 mmio: [d6000000, d7ffffff]
[ 0.679647] bus: 02 index 2 mmio: [d2000000, d3ffffff]
[ 0.679650] bus: 02 index 3 mmio: [0, 0]
[ 0.679652] bus: 03 index 0 io port: [3000, 3fff]
[ 0.679655] bus: 03 index 1 mmio: [d4000000, d5ffffff]
[ 0.679659] bus: 03 index 2 mmio: [d0000000, d1ffffff]
[ 0.679661] bus: 03 index 3 mmio: [0, 0]
[ 0.679664] bus: 05 index 0 io port: [4000, 4fff]
[ 0.679667] bus: 05 index 1 mmio: [d8000000, d80fffff]
[ 0.679670] bus: 05 index 2 mmio: [0, 0]
[ 0.679673] bus: 05 index 3 io port: [0, ffff]
[ 0.679676] bus: 05 index 4 mmio: [0, ffffffff]
[ 0.679687] NET: Registered protocol family 2
[ 0.692064] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.692361] TCP established hash table entries: 131072 (order: 8,
1048576 bytes)
[ 0.692933] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.693247] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.693251] TCP reno registered
[ 0.700115] NET: Registered protocol family 1
[ 0.700261] checking if image is initramfs... it is
[ 1.579330] Freeing initrd memory: 8002k freed
[ 1.579566] Simple Boot Flag at 0x35 set to 0x1
[ 1.580826] audit: initializing netlink socket (disabled)
[ 1.580857] type=2000 audit(1248984065.580:1): initialized
[ 1.587409] highmem bounce pool size: 64 pages
[ 1.587417] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 1.590796] VFS: Disk quotas dquot_6.5.1
[ 1.590916] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.591056] msgmni has been set to 1762
[ 1.591216] io scheduler noop registered
[ 1.591220] io scheduler anticipatory registered
[ 1.591223] io scheduler deadline registered
[ 1.591239] io scheduler cfq registered (default)
[ 1.591256] pci 0000:00:02.0: Boot video device
[ 1.591388] pci 0000:05:08.0: Firmware left e100 interrupts
enabled; disabling
[ 1.591540] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[ 1.591595] pcieport-driver 0000:00:1c.0: found MSI capability
[ 1.591652] pci_express 0000:00:1c.0:pcie00: allocate port service
[ 1.591714] pci_express 0000:00:1c.0:pcie02: allocate port service
[ 1.591772] pci_express 0000:00:1c.0:pcie03: allocate port service
[ 1.591905] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[ 1.591958] pcieport-driver 0000:00:1c.1: found MSI capability
[ 1.592010] pci_express 0000:00:1c.1:pcie00: allocate port service
[ 1.592068] pci_express 0000:00:1c.1:pcie02: allocate port service
[ 1.592126] pci_express 0000:00:1c.1:pcie03: allocate port service
[ 1.592603] isapnp: Scanning for PnP cards...
[ 1.946684] isapnp: No Plug & Play device found
[ 1.994229] hpet_resources: 0xfed00000 is busy
[ 1.994320] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[ 1.997323] brd: module loaded
[ 1.997420] input: Macintosh mouse button emulation as
/devices/virtual/input/input0
[ 1.997580] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
[ 2.014169] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 2.014177] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 2.016155] mice: PS/2 mouse device common for all mice
[ 2.016330] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 2.016365] rtc0: alarms up to one month, y3k, hpet irqs
[ 2.016534] EISA: Probing bus 0 at eisa.0
[ 2.016543] Cannot allocate resource for EISA slot 1
[ 2.016547] Cannot allocate resource for EISA slot 2
[ 2.016550] Cannot allocate resource for EISA slot 3
[ 2.016553] Cannot allocate resource for EISA slot 4
[ 2.016575] EISA: Detected 0 cards.
[ 2.016579] cpuidle: using governor ladder
[ 2.016582] cpuidle: using governor menu
[ 2.017245] TCP cubic registered
[ 2.017278] Using IPI No-Shortcut mode
[ 2.017515] registered taskstats version 1
[ 2.017669] Magic number: 1:345:44
[ 2.017676] tty ttyed: hash matches
[ 2.017798] rtc_cmos 00:07: setting system clock to 2009-07-30
20:01:07 UTC (1248984067)
[ 2.017802] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 2.017805] EDD information not available.
[ 2.018103] Freeing unused kernel memory: 428k freed
[ 2.018163] Write protecting the kernel text: 2580k
[ 2.018200] Write protecting the kernel read-only data: 940k
[ 2.035077] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input1
[ 2.249161] fuse init (API version 7.9)
[ 2.289698] ACPI: SSDT 3F67E646, 01E5 (r1 HP 30BB 3000
INTL 20050624)
[ 2.290189] ACPI: SSDT 3F67E3E5, 01DC (r1 HP 30BB 3001
INTL 20050624)
[ 2.337184] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 2.337253] processor ACPI0007:00: registered as cooling_device0
[ 2.337259] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 2.337747] ACPI: SSDT 3F67E82B, 0094 (r1 HP 30BB 3000
INTL 20050624)
[ 2.338211] ACPI: SSDT 3F67E5C1, 0085 (r1 HP 30BB 3000
INTL 20050624)
[ 2.339009] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 2.339068] processor ACPI0007:01: registered as cooling_device1
[ 2.339074] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 2.342374] Marking TSC unstable due to TSC halts in idle
[ 2.346666] thermal LNXTHERM:01: registered as thermal_zone0
[ 2.356077] ACPI: Thermal Zone [THR1] (45 C)
[ 2.771106] usbcore: registered new interface driver usbfs
[ 2.771136] usbcore: registered new interface driver hub
[ 2.771177] usbcore: registered new device driver usb
[ 2.784818] USB Universal Host Controller Interface driver v3.0
[ 2.784879] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 2.784890] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[ 2.784896] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 2.784947] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned
bus number 1
[ 2.784989] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001820
[ 2.785187] usb usb1: configuration #1 chosen from 1 choice
[ 2.785222] hub 1-0:1.0: USB hub found
[ 2.785231] hub 1-0:1.0: 2 ports detected
[ 2.888347] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 2.888360] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[ 2.888366] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 2.888397] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned
bus number 2
[ 2.888441] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001840
[ 2.888565] usb usb2: configuration #1 chosen from 1 choice
[ 2.888604] hub 2-0:1.0: USB hub found
[ 2.888614] hub 2-0:1.0: 2 ports detected
[ 2.901567] Warning! ehci_hcd should always be loaded before
uhci_hcd and ohci_hcd, not after
[ 2.925486] No dock devices found.
[ 2.966491] SCSI subsystem initialized
[ 3.002071] libata version 3.00 loaded.
[ 3.021502] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
[ 3.021506] e100: Copyright(c) 1999-2006 Intel Corporation
[ 3.096376] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[ 3.096389] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[ 3.096394] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 3.096431] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned
bus number 3
[ 3.096474] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001860
[ 3.096601] usb usb3: configuration #1 chosen from 1 choice
[ 3.096638] hub 3-0:1.0: USB hub found
[ 3.096647] hub 3-0:1.0: 2 ports detected
[ 3.200465] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[ 3.200479] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[ 3.200484] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 3.200517] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned
bus number 4
[ 3.200562] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00001880
[ 3.200685] usb usb4: configuration #1 chosen from 1 choice
[ 3.200721] hub 4-0:1.0: USB hub found
[ 3.200730] hub 4-0:1.0: 2 ports detected
[ 3.208044] usb 2-1: new low speed USB device using uhci_hcd and address 2
[ 3.304762] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 3.304783] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[ 3.304788] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 3.304821] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned
bus number 5
[ 3.308749] ehci_hcd 0000:00:1d.7: debug port 1
[ 3.308758] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[ 3.308769] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd8444000
[ 3.340044] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00,
driver 10 Dec 2004
[ 3.340261] usb usb5: configuration #1 chosen from 1 choice
[ 3.340303] hub 5-0:1.0: USB hub found
[ 3.340314] hub 5-0:1.0: 8 ports detected
[ 3.500079] Clocksource tsc unstable (delta = -116966894 ns)
[ 3.544802] ata_piix 0000:00:1f.1: version 2.12
[ 3.544819] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[ 3.544869] ata_piix 0000:00:1f.1: setting latency timer to 64
[ 3.544998] scsi0 : ata_piix
[ 3.545363] scsi1 : ata_piix
[ 3.546140] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1810 irq 14
[ 3.546144] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15
[ 3.708629] ata1.00: ATAPI: PHILIPS DVD-RAM SDVD8821, EH19, max MWDMA2
[ 3.724505] ata1.00: configured for MWDMA2
[ 3.724594] ata2: port disabled. ignoring.
[ 3.726276] scsi 0:0:0:0: CD-ROM PHILIPS DVD-RAM
SDVD8821 EH19 PQ: 0 ANSI: 5
[ 3.726418] ahci 0000:00:1f.2: version 3.0
[ 3.726431] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[ 3.726559] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5
Gbps 0x5 impl SATA mode
[ 3.726564] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
[ 3.726571] ahci 0000:00:1f.2: setting latency timer to 64
[ 3.727116] scsi2 : ahci
[ 3.727463] scsi3 : ahci
[ 3.727810] scsi4 : ahci
[ 3.728192] scsi5 : ahci
[ 3.728331] ata3: SATA max UDMA/133 abar m1024@0xd8444400 port
0xd8444500 irq 221
[ 3.728335] ata4: DUMMY
[ 3.728339] ata5: SATA max UDMA/133 abar m1024@0xd8444400 port
0xd8444600 irq 221
[ 3.728342] ata6: DUMMY
[ 3.736073] usb 2-1: device not accepting address 2, error -71
[ 3.792112] hub 2-0:1.0: unable to enumerate USB device on port 1
[ 4.048124] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 4.048781] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
[ 4.048788] ata3.00: ATA-7: FUJITSU MHV2100BH PL, 892C, max UDMA/100
[ 4.048791] ata3.00: 195371568 sectors, multi 16: LBA48
[ 4.051413] ata3.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
[ 4.051433] ata3.00: configured for UDMA/100
[ 4.088094] usb 5-4: new high speed USB device using ehci_hcd and address 3
[ 4.221683] usb 5-4: configuration #1 chosen from 1 choice
[ 4.384158] ata5: SATA link down (SStatus 0 SControl 300)
[ 4.400431] scsi 2:0:0:0: Direct-Access ATA FUJITSU
MHV2100B 892C PQ: 0 ANSI: 5
[ 4.400632] e100 0000:05:08.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 4.400699] e100 0000:05:08.0: setting latency timer to 64
[ 4.428541] e100 0000:05:08.0: PME# disabled
[ 4.432393] e100: eth0: e100_probe: addr 0xd8000000, irq 20, MAC
addr 00:16:36:86:e5:3e
[ 4.434665] ohci1394 0000:05:05.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 4.434674] ohci1394 0000:05:05.0: setting latency timer to 64
[ 4.487416] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16]
MMIO=[d8001000-d80017ff] Max Packet=[2048] IR/IT contexts=[4/4]
[ 4.492138] usb 2-1: new low speed USB device using uhci_hcd and address 4
[ 4.492946] scsi 0:0:0:0: Attached scsi generic sg0 type 5
[ 4.492998] scsi 2:0:0:0: Attached scsi generic sg1 type 0
[ 4.538157] Driver 'sd' needs updating - please use bus_type methods
[ 4.539083] sd 2:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 4.539116] sd 2:0:0:0: [sda] Write Protect is off
[ 4.539120] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.539155] sd 2:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.539252] sd 2:0:0:0: [sda] 195371568 512-byte hardware sectors (100030 MB)
[ 4.539272] sd 2:0:0:0: [sda] Write Protect is off
[ 4.539275] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.539310] sd 2:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 4.539315] sda:<4>Driver 'sr' needs updating - please use bus_type methods
[ 4.557138] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw
xa/form2 cdda tray
[ 4.557143] Uniform CD-ROM driver Revision: 3.20
[ 4.557252] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 4.613917] sda1 sda2 sda3 < sda5 >
[ 4.639107] sd 2:0:0:0: [sda] Attached SCSI disk
[ 4.670515] usb 2-1: configuration #1 chosen from 1 choice
[ 4.699518] usbcore: registered new interface driver hiddev
[ 4.715002] input: CHESEN USB Keyboard as
/devices/pci0000:00/0000:00:1d.1/usb2/2-1/2-1:1.0/input/input2
[ 4.715466] input,hidraw0: USB HID v1.10 Keyboard [CHESEN USB
Keyboard] on usb-0000:00:1d.1-1
[ 4.741669] input: CHESEN USB Keyboard as
/devices/pci0000:00/0000:00:1d.1/usb2/2-1/2-1:1.1/input/input3
[ 4.742037] input,hidraw1: USB HID v1.10 Device [CHESEN USB
Keyboard] on usb-0000:00:1d.1-1
[ 4.742064] usbcore: registered new interface driver usbhid
[ 4.742069] usbhid: v2.6:USB HID core driver
[ 4.836373] PM: Starting manual resume from disk
[ 4.836378] PM: Resume from partition 8:2
[ 4.836381] PM: Checking hibernation image.
[ 4.836600] PM: Resume from disk failed.
[ 4.903007] kjournald starting. Commit interval 5 seconds
[ 4.903041] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.780266] ieee1394: Host added: ID:BUS[0-00:1023] GUID[009fc000f03bb500]
[ 11.109571] udevd version 124 started
[ 11.576165] Linux agpgart interface v0.103
[ 11.712189] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 11.804246] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 11.872191] agpgart-intel 0000:00:00.0: Intel 945GM Chipset
[ 11.872828] agpgart-intel 0000:00:00.0: detected 7932K stolen memory
[ 11.877868] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xc0000000
[ 11.982124] input: Power Button (FF) as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input4
[ 12.008019] ACPI: Power Button (FF) [PWRF]
[ 12.008134] input: Power Button (CM) as
/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
[ 12.032033] ACPI: Power Button (CM) [PWRB]
[ 12.032201] input: Sleep Button (CM) as
/devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input6
[ 12.056033] ACPI: Sleep Button (CM) [SLPB]
[ 12.056175] input: Lid Switch as
/devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input7
[ 12.056868] ACPI: Lid Switch [LID]
[ 12.140286] ACPI: WMI: Mapper loaded
[ 12.189555] ACPI: AC Adapter [ACAD] (on-line)
[ 12.325308] input: Video Bus as
/devices/LNXSYSTM:00/device:00/PNP0A08:00/device:07/input/input8
[ 12.344048] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 12.399352] ACPI: Battery Slot [BAT0] (battery absent)
[ 12.962133] iTCO_vendor_support: vendor-support=0
[ 13.052181] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.03 (30-Apr-2008)
[ 13.052319] iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x1060)
[ 13.052493] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 13.088144] ricoh-mmc: Ricoh MMC Controller disabling driver
[ 13.088149] ricoh-mmc: Copyright(c) Philip Langdale
[ 13.088195] ricoh-mmc: Ricoh MMC controller found at 0000:05:05.2
[1180:0843] (rev 1)
[ 13.088219] ricoh-mmc: Controller is now disabled.
[ 13.399007] intel_rng: FWH not detected
[ 13.436699] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network
Connection driver for Linux, 1.2.26ks
[ 13.436704] iwl3945: Copyright(c) 2003-2008 Intel Corporation
[ 13.437891] iwl3945 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 13.437908] iwl3945 0000:02:00.0: setting latency timer to 64
[ 13.437932] iwl3945: Detected Intel Wireless WiFi Link 3945ABG
[ 13.480826] iwl3945: Tunable channels: 13 802.11bg, 23 802.11a channels
[ 13.482510] phy0: Selected rate control algorithm 'iwl-3945-rs'
[ 13.552825] input: PC Speaker as /devices/platform/pcspkr/input/input9
[ 13.589825] sdhci: Secure Digital Host Controller Interface driver
[ 13.589830] sdhci: Copyright(c) Pierre Ossman
[ 13.712492] sdhci-pci 0000:05:05.1: SDHCI controller found
[1180:0822] (rev 19)
[ 13.712508] sdhci-pci 0000:05:05.1: enabling device (0000 -> 0002)
[ 13.712519] sdhci-pci 0000:05:05.1: PCI INT B -> GSI 17 (level,
low) -> IRQ 17
[ 13.714602] mmc0: SDHCI controller on PCI [0000:05:05.1] using PIO
[ 14.038131] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level,
low) -> IRQ 22
[ 14.038167] HDA Intel 0000:00:1b.0: setting latency timer to 64
[ 14.372113] Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1,
caps: 0xa04713/0x200000
[ 14.431040] input: SynPS/2 Synaptics TouchPad as
/devices/platform/i8042/serio1/input/input10
[ 15.186728] lp: driver loaded but no devices found
[ 15.381751] Adding 8024k swap on /dev/sda2. Priority:-1 extents:1
across:8024k
[ 15.926809] EXT3 FS on sda1, internal journal
[ 16.823134] kjournald starting. Commit interval 5 seconds
[ 16.823578] EXT3 FS on sda5, internal journal
[ 16.823585] EXT3-fs: mounted filesystem with ordered data mode.
[ 17.067112] type=1505 audit(1248984082.089:2):
operation="profile_load" name="/usr/share/gdm/guest-session/Xsession"
name2="default" pid=4216
[ 17.299592] type=1505 audit(1248984082.321:3):
operation="profile_load" name="/usr/lib/cups/backend/cups-pdf"
name2="default" pid=4221
[ 17.299850] type=1505 audit(1248984082.321:4):
operation="profile_load" name="/usr/sbin/cupsd" name2="default"
pid=4221
[ 17.483731] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 19.184447] warning: `avahi-daemon' uses 32-bit capabilities
(legacy support in use)
[ 19.246387] apm: BIOS not found.
[ 19.406343] ppdev: user-space parallel port driver
[ 21.493394] Bluetooth: Core ver 2.13
[ 21.493546] NET: Registered protocol family 31
[ 21.493556] Bluetooth: HCI device and connection manager initialized
[ 21.493569] Bluetooth: HCI socket layer initialized
[ 21.520777] Bluetooth: L2CAP ver 2.11
[ 21.520792] Bluetooth: L2CAP socket layer initialized
[ 21.561812] Bluetooth: SCO (Voice Link) ver 0.6
[ 21.561829] Bluetooth: SCO socket layer initialized
[ 21.578449] Bluetooth: RFCOMM socket layer initialized
[ 21.578477] Bluetooth: RFCOMM TTY layer initialized
[ 21.578483] Bluetooth: RFCOMM ver 1.10
[ 21.596450] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 21.596465] Bluetooth: BNEP filters: protocol multicast
[ 21.650290] Bridge firewalling registered
[ 25.821825] firmware: requesting iwlwifi-3945-1.ucode
[ 25.849540] [drm] Initialized drm 1.1.0 20060810
[ 25.875473] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 25.875492] pci 0000:00:02.0: setting latency timer to 64
[ 25.877501] [drm] Initialized i915 1.6.0 20060119 on minor 0
[ 25.991183] Registered led device: iwl-phy0:radio
[ 25.991835] Registered led device: iwl-phy0:assoc
[ 25.992281] Registered led device: iwl-phy0:RX
[ 25.992721] Registered led device: iwl-phy0:TX
[ 26.371580] NET: Registered protocol family 17
[ 59.045196] CPU0 attaching NULL sched-domain.
[ 59.045217] CPU1 attaching NULL sched-domain.
[ 59.048264] CPU0 attaching sched-domain:
[ 59.048275] domain 0: span 0-1 level MC
[ 59.048282] groups: 0 1
[ 59.048296] CPU1 attaching sched-domain:
[ 59.048301] domain 0: span 0-1 level MC
[ 59.048307] groups: 1 0
Module Size Used by
af_packet 25856 2
i915 38656 2
drm 86056 3 i915
binfmt_misc 16904 1
bridge 56980 0
stp 10628 1 bridge
bnep 20352 2
rfcomm 44304 0
sco 18308 2
l2cap 30464 6 bnep,rfcomm
bluetooth 61924 6 bnep,rfcomm,sco,l2cap
ppdev 15748 0
acpi_cpufreq 15500 0
cpufreq_userspace 11396 0
cpufreq_ondemand 14988 2
cpufreq_stats 13188 0
cpufreq_powersave 9856 0
cpufreq_conservative 14600 0
freq_table 12672 3 acpi_cpufreq,cpufreq_ondemand,cpufreq_stats
container 11520 0
sbs 19464 0
sbshc 13440 1 sbs
pci_slot 12680 0
iptable_filter 10752 0
ip_tables 19600 1 iptable_filter
x_tables 22916 1 ip_tables
sbp2 29324 0
parport_pc 39332 0
lp 17156 0
parport 42604 3 ppdev,parport_pc,lp
joydev 18368 0
snd_hda_intel 385072 2
snd_pcm_oss 46848 0
snd_mixer_oss 22784 1 snd_pcm_oss
snd_pcm 83204 2 snd_hda_intel,snd_pcm_oss
snd_seq_dummy 10884 0
arc4 9984 2
ecb 10880 2
crypto_blkcipher 25476 1 ecb
snd_seq_oss 38528 0
sdhci_pci 15360 0
sdhci 23940 1 sdhci_pci
psmouse 45200 0
pcspkr 10624 0
serio_raw 13444 0
iwl3945 99316 0
mmc_core 58268 1 sdhci
evdev 17696 14
rfkill 17048 2 iwl3945
ricoh_mmc 11904 0
iTCO_wdt 18596 0
iTCO_vendor_support 11652 1 iTCO_wdt
mac80211 216820 1 iwl3945
snd_seq_midi 14336 0
led_class 12164 1 iwl3945
snd_rawmidi 29824 1 snd_seq_midi
cfg80211 32392 2 iwl3945,mac80211
snd_seq_midi_event 15232 2 snd_seq_oss,snd_seq_midi
snd_seq 57776 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 29960 2 snd_pcm,snd_seq
snd_seq_device 15116 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
battery 18436 0
snd 63268 13
snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
video 25488 0
output 11008 1 video
ac 12292 0
wmi 14504 0
soundcore 15328 1 snd
button 14224 0
intel_agp 33980 1
shpchp 38036 0
pci_hotplug 34976 1 shpchp
snd_page_alloc 16136 2 snd_hda_intel,snd_pcm
agpgart 42184 3 drm,intel_agp
ext3 133384 2
jbd 55828 1 ext3
mbcache 16004 1 ext3
usbhid 35712 0
hid 50560 1 usbhid
sr_mod 22212 0
cdrom 43168 1 sr_mod
sd_mod 42392 4
crc_t10dif 9984 1 sd_mod
ata_generic 12932 0
sg 39732 0
pata_acpi 12160 0
ohci1394 37936 0
ahci 37132 3
e100 41356 0
ata_piix 24708 0
ieee1394 96324 2 sbp2,ohci1394
mii 13440 1 e100
libata 177952 4 ata_generic,pata_acpi,ahci,ata_piix
scsi_mod 155212 5 sbp2,sr_mod,sd_mod,sg,libata
dock 16656 1 libata
ehci_hcd 43788 0
uhci_hcd 30864 0
usbcore 149488 4 usbhid,ehci_hcd,uhci_hcd
thermal 23708 0
processor 42156 4 acpi_cpufreq,thermal
fan 12548 0
fbcon 47648 0
tileblit 10880 1 fbcon
font 16512 1 fbcon
bitblit 13824 1 fbcon
softcursor 9984 1 bitblit
fuse 60956 3
