Jaysen,
The Makefile stuff refers to the original slmodem software set, which
I used to compile the slmodemd you just installed.
So just ignore it as already done.
>>> PCI slot 00:1b.0 has a High Definition Audio Card
>>> The drivers are in the kernel modules tree at:
>>> /lib/modules/2.6.28-13-generic/kernel/sound/pci/hda/snd-hda-intel.ko
>>> /lib/modules/2.6.28-11-generic/kernel/sound/pci/hda/snd-hda-intel.ko
>>> The modem codec file for the HDA card is: /proc/asound/card0/codec#1
>>> --------------------------------------------------------
>>> Codec: Motorola Si3054
>>> Address: 1
>>> Vendor Id: 0x10573055
Your audio + modem driver is the snd-hda-intel.ko automatically
installed in support of the High Definition Audio Card
whose Subsystem hosts the Motorola Si3054 0x10573055 modem chip
Such chips do little more then specify which software should be used
under Microsoft, which would be a Motorola software package
instructing the CPU what to do.
Under Linux there is no Motorola software, but instead the Smart
slmodemd utility (not a driver) substitutes.
The
$ sudo slmodemd -c USA --alsa hw:0,6
> SmartLink Soft Modem: version 2.9.11 Aug 3 2008 22:31:06
> symbolic link `/dev/ttySL0' -> `/dev/pts/1' created.
> modem `hw:0,6' created. TTY is `/dev/pts/1'
> Use `/dev/ttySL0' as modem device, Ctrl+C for termination.
did effectively activate the modem. The Ubuntu sl-modem-daemon
package does the same thing, additionally running upon bootup the:
slmodemd -c USA --alsa hw:0,6
You don't need the sl-modem-source package, as it is not for HDA modem
type hardware
With the modem activated, you should be able to open a console and
further test the modem.
But first do while online
$ sudo apt-get install wvdial
When done
$ sudo wvdialconf
should find the modem
Read the wvdial.txt sample and
$ sudo gedit /etc/wvdial.conf
to edit in your dialout info.
They shut down ethernet/LAN/wireless or they will block new DNS for the modem.
THen try a dialout with
$ sudo wvdial
Please write to the List, not me directly as I am ony online in the evening.
MarvS
On Mon, Jul 20, 2009 at 10:15 PM, Jaysen Johnson<jaysen@xxxxxxxxxxxx> wrote:
> Hi Marvin,
>
> I am very confused. I downloaded the package, extracted it and ran the sudo
> ./setup Then I read the README file which tells me about a MAKEFILE that I
> need to review and edit if necessary but no MAKEFILE exists in the package.
> ???
>
> when I run sudo slmodemd -c USA --alsa hw:0,6 I get the following output
> below.
>
>
> jaysen@jaysens-laptop:~/Downloads/SLMODEMD.gcc4.3$ sudo slmodemd -c USA
> --alsa hw:0,6
> SmartLink Soft Modem: version 2.9.11 Aug 3 2008 22:31:06
> symbolic link `/dev/ttySL0' -> `/dev/pts/1' created.
> modem `hw:0,6' created. TTY is `/dev/pts/1'
> Use `/dev/ttySL0' as modem device, Ctrl+C for termination.
>
> Ubuntu 9.04 has an Softmodem driver that i can install from the restricted
> drivers manager which basically installed the slmodemd application. How is
> this method different? I really am stuck here.
>
>
> Jaysen
>
>
>
> Marvin Stodolsky wrote:
>>
>> Jaysen
>>
>> Try:
>> Download from http://linmodems.technion.ac.il/packages/smartlink/
>> the package SLMODEMD.gcc4.3.tar.gz having a compiled slmodemd. Unpack
>> under Linux with:
>> $ tar zxf SLMODEMD.gcc4.3.tar.gz
>> and read instructions therein. But briefly, the modem is setup with
>> command:
>> sudo slmodemd -c USA --alsa hw:0,6
>> reporting dynamic creation of ports:
>> /dev/ttySL0 --> /dev/pts/N , with N some number
>> Read DOCs/Smartlink.txt and Modem/DOCs/YourSystem.txt for follow
>> through guidance.
>>
>> Within the SLMODEMD.gcc4.3 folder, run
>> $ sudo ./setup
>>
>> which will run elementary tests and output instructions. This "sudo
>> ./setup" does not have to be repeated again.
>> Read the instructions in the SLMODEMD.gcc4.3/ folder for details.
>> Info us in some detail at which step you may run into trouble.
>>
>> MarvS
>> scanmodem maintainer
>>
>>
>> On Mon, Jul 20, 2009 at 9:02 PM, Jaysen Johnson<jaysen@xxxxxxxxxxxx>
>> wrote:
>>>
>>> Hello,
>>>
>>> I am trying to configure a SmartLink modem under Ubuntu 9.04 Jaunty
>>> Jackalope 64Bit. I am having a hard time getting it to work. I am in
>>> the
>>> USA and sending my ModemData.txt file.
>>>
>>> If you need more information to help me. Please let me know.
>>>
>>> Thank You,
>>>
>>> Jaysen
>>>
>>>
>>> Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List
>>> Server,
>>> as HTML can contain viruses. Use as the email Subject Line:
>>> YourName, YourCountry kernel 2.6.28-13-generic
>>> With this Subject Line cogent experts will be alerted, and useful case
>>> names left in the Archive.
>>> YourCountry will enable Country specific guidance. Linux experts in
>>> YourCountry
>>> can be found through: http://www.linux.org/groups/index.html.
>>> They will know your Country's modem code, which may be essential for
>>> dialup
>>> service.
>>> Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an Internet
>>> Provider mail filters.
>>> So in a day, also check the Archived responses at
>>> http://www.linmodems.org
>>> -------------------------- System information
>>> ----------------------------
>>> CPU=x86_64,
>>> Linux version 2.6.28-13-generic (buildd@yellow) (gcc version 4.3.3
>>> (Ubuntu
>>> 4.3.3-5ubuntu4) ) #45-Ubuntu SMP Tue Jun 30 22:12:12 UTC 2009
>>> scanModem update of: 2009_07_17
>>> The modem symbolic link is /dev/modem -> ttySL0
>>> The slmodemd set symbolic link is /dev/ttySL0 -> /dev/pts/2
>>>
>>> Some modem drivers can only be used in 32 bit modem on x86_64 systems,
>>> while some others are competent on x86_64 Systems. Cases are:
>>> 1) http://linmodems.technion.ac.il/bigarch/archive-seventh/msg03119.html
>>> for the snd-hda-intel audio+modem driver. Also applicable to AC97 modem
>>> controllers.
>>> In both cases, 32 bit libraries must be installed to support the slmodemd
>>> helper having a precompiled 32 bit component.
>>> 2) For USB modems using the slusb.ko driver. 32 bit libraries must be
>>> installed to support the slmodemd helper having a precompiled 32 bit
>>> component
>>> 3) The hsfmodem and hcfpcimodem drivers for Conexant chipsest modes are
>>> x86_64 competent.
>>>
>>> There are no blacklisted modem drivers in /etc/modprobe* files
>>> Potentially useful modem drivers now loaded are:
>>> snd_hda_intel
>>>
>>> Attached USB devices are:
>>> ID 04f2:b018 Chicony Electronics Co., Ltd Video Device
>>> ID 0a5c:2101 Broadcom Corp. A-Link BlueUsbA2 Bluetooth
>>> If a cellphone is not detected, see
>>> http://ubuntuforums.org/archive/index.php/t-878554.html
>>> A sample report is:
>>> http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html
>>>
>>> If a USB modem or cellphone is attached and was not detected, please
>>> provide available information in your request to discuss@xxxxxxxxxxxxx
>>>
>>> For candidate card in slot 00:1b.0, firmware information and bootup
>>> diagnostics are:
>>> PCI slot PCI ID SubsystemID Name
>>> ---------- --------- --------- --------------
>>> 00:1b.0 8086:284b 14c0:0025 Audio device: Intel
>>> Corporation 82801H
>>>
>>> Modem interrupt assignment and sharing:
>>> 20: 1346 1349 IO-APIC-fasteoi HDA Intel
>>> --- Bootup diagnostics for card in PCI slot 00:1b.0 ----
>>> [ 0.549224] pci 0000:00:1b.0: reg 10 64bit mmio:
>>> [0xf8400000-0xf8403fff]
>>> [ 0.549266] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
>>> [ 0.549271] pci 0000:00:1b.0: PME# disabled
>>> [ 13.797697] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 20 (level, low)
>>> ->
>>> IRQ 20
>>> [ 13.797784] HDA Intel 0000:00:1b.0: setting latency timer to 64
>>>
>>> The PCI slot 00:1b.0 of the modem card may be disabled early in
>>> a bootup process, but then enabled later. If modem drivers load
>>> but the modem is not responsive, read DOCs/Bootup.txt about possible
>>> fixes.
>>> Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
>>> if help is needed.
>>>
>>>
>>>
>>> ===== Advanced Linux Sound Architecture (ALSA) diagnostics =====
>>> The ALSA packages provide audio support and also drivers for some modems.
>>> ALSA diagnostics are written during bootup to /proc/asound/ folders.
>>>
>>> The ALSA verion is 1.0.18
>>> The modem cards detected by "aplay -l" are:
>>> card 0: Intel [HDA Intel], device 6: Si3054 Modem [Si3054 Modem]
>>>
>>> The /proc/asound/pcm file reports:
>>> -----------------------
>>> 00-00: ALC268 Analog : ALC268 Analog : playback 1 : capture 1
>>> 00-06: Si3054 Modem : Si3054 Modem : playback 1 : capture 1
>>>
>>> about /proc/asound/cards:
>>> ------------------------
>>> 0 [Intel ]: HDA-Intel - HDA Intel
>>> HDA Intel at 0xf8400000 irq 20
>>> ===== Advanced Linux Sound Architecture (ALSA) diagnostics =====
>>> The ALSA packages provide audio support and also drivers for some modems.
>>> ALSA diagnostics are written during bootup to /proc/asound/ folders.
>>>
>>> The ALSA verion is 1.0.18
>>> The modem cards detected by "aplay -l" are:
>>> card 0: Intel [HDA Intel], device 6: Si3054 Modem [Si3054 Modem]
>>>
>>> The /proc/asound/pcm file reports:
>>> -----------------------
>>> 00-00: ALC268 Analog : ALC268 Analog : playback 1 : capture 1
>>> 00-06: Si3054 Modem : Si3054 Modem : playback 1 : capture 1
>>>
>>> about /proc/asound/cards:
>>> ------------------------
>>> 0 [Intel ]: HDA-Intel - HDA Intel
>>> HDA Intel at 0xf8400000 irq 20
>>>
>>> PCI slot 00:1b.0 has a High Definition Audio Card
>>> The drivers are in the kernel modules tree at:
>>> /lib/modules/2.6.28-13-generic/kernel/sound/pci/hda/snd-hda-intel.ko
>>> /lib/modules/2.6.28-11-generic/kernel/sound/pci/hda/snd-hda-intel.ko
>>> The modem codec file for the HDA card is: /proc/asound/card0/codec#1
>>> --------------------------------------------------------
>>> Codec: Motorola Si3054
>>> Address: 1
>>> Vendor Id: 0x10573055
>>> Subsystem Id: 0x10573055
>>> Revision Id: 0x100700
>>> Modem Function Group: 0x1
>>>
>>> The audio card hosts a softmodem chip: 0x10573055
>>>
>>> The softmodem chip 0x10573055 is in principle supported by the COMM
>>> support
>>> of slmodemd
>>> and the joint snd-hda-intel audio+modem driver, begun with ALSA version
>>> 1.0.13.
>>> For HDA cards with ALC883 chips, an upgrade to ALSA verions 1.0.15 way be
>>> necessary. Instructions for Upgrading snd-hda-intel and its dependent
>>> driver
>>> set are at:
>>> http://linmodems.technion.ac.il/bigarch/archive-eighth/msg00838.html
>>>
>>> If not a Conexant modem, the driver snd-hda-intel with its dependent
>>> drivers:
>>> snd_hda_intel 557492 6
>>> snd_pcm 99336 4 snd_hda_intel,snd_pcm_oss
>>> snd 78792 19
>>>
>>> snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
>>> snd_page_alloc 18704 2 snd_hda_intel,snd_pcm
>>> ----------
>>> provide audio + modem support with the modem chip residing on the
>>> subsystem.
>>> Any particular card can host any one of several soft modem chips.
>>>
>>> === Finished firmware and bootup diagnostics, next deducing cogent
>>> software.
>>> ===
>>>
>>> Predictive diagnostics for card in bus 00:1b.0:
>>> Modem chipset detected on
>>> NAME="Audio device: Intel Corporation 82801H "
>>> CLASS=0403
>>> PCIDEV=8086:284b
>>> SUBSYS=14c0:0025
>>> IRQ=20
>>> HDA=8086:284b
>>> SOFT=8086:284b.HDA
>>> HDAchipVendorID=1057
>>> CHIP=0x10573055
>>> IDENT=slmodemd
>>> SLMODEMD_DEVICE=hw:0,6
>>> Driver=snd-hda-intel
>>>
>>> For candidate modem in: 00:1b.0
>>> 0403 Audio device: Intel Corporation 82801H
>>> Primary device ID: 8086:284b
>>> Subsystem PCI_id 14c0:0025
>>> Softmodem codec or chipset from diagnostics: 0x10573055
>>> from Archives:
>>> The HDA card softmodem chip is 0x10573055
>>>
>>>
>>> Support type needed or chipset: slmodemd supporting the snd-hda-intel
>>> audio+modem driver
>>>
>>> An ALSA (Advanced Linux Sound Architecture) modem driver: snd-hda-intel
>>> provides Low Level support enabling contact with the modem hardware.
>>> For all BUT Conexant chip soft modems (using hsfmodem software)
>>> complementary High Level support is through a Smartlink utility:
>>> slmodemd
>>>
>>> Download from http://linmodems.technion.ac.il/packages/smartlink/
>>> the package SLMODEMD.gcc4.3.tar.gz having a compiled slmodemd. Unpack
>>> under
>>> Linux with:
>>> $ tar zxf SLMODEMD.gcc4.3.tar.gz
>>> and read instructions therein. But briefly, the modem is setup with
>>> command:
>>> sudo slmodemd -c YOUR_COUNTRY --alsa hw:0,6
>>> reporting dynamic creation of ports:
>>> /dev/ttySL0 --> /dev/pts/N , with N some number
>>> Read DOCs/Smartlink.txt and Modem/DOCs/YourSystem.txt for follow through
>>> guidance.
>>>
>>>
>>> Writing DOCs/Intel.txt
>>> Writing DOCs/Smartlink.txt
>>> ============ end Smartlink section =====================
>>>
>>> Completed candidate modem analyses.
>>>
>>> The base of the UDEV device file system is: /dev/.udev
>>>
>>> Versions adequately match for the compiler installed: 4.3.3
>>> and the compiler used in kernel assembly: 4.3.3
>>>
>>>
>>>
>>> Minimal compiling resources appear complete:
>>> make utility - /usr/bin/make
>>> Compiler version 4.3
>>> linuc_headers base folder /lib/modules/2.6.28-13-generic/build
>>>
>>> However some compilations and executable functions may need additional
>>> files,
>>> in the FileNames.h (so called kernel "h"eaders) collection installed in
>>> /usr/include/ .
>>> For martian_modem, additional required packages are needed. The also
>>> required headers of package libc6 are commonly installed by default.
>>> Compiling hsfmodem drivers does require linux-libc-dev and libc6-dev
>>> packages, for kernels 2.6.24 and later versions.
>>> In not included on your install CD, search for them at
>>> http://packages.ubuntu.com
>>> or comparable Repository for other Linux distros.
>>> When compiling ALSA drivers, the utility "patch" will also be needed.
>>>
>>>
>>>
>>>
>>> If a driver compilation fails, with message including some lack of some
>>> FileName.h (stdio.h for example), then
>>> Some additional kernel-header files need installation to /usr/include.
>>> The
>>> minimal additional packages are libc6-dev
>>> and any of its dependents, under Ubuntu linux-libc-dev
>>>
>>> If an alternate ethernet connection is available,
>>> $ apt-get update
>>> $ apt-get -s install linux-kernel-devel
>>> will install needed packages.
>>> For Debian/Ubuntu related distributions, run the following command to
>>> display the needed package list:
>>>
>>> Otherwise packages have to be found through http://packages.ubuntu.com
>>> Once downloaded and transferred into a Linux partition,
>>> they can be installed alltogether with:
>>> $ sudo dpkg -i *.deb
>>>
>>> Checking settings of: /etc/ppp/options
>>> asyncmap 0
>>> noauth
>>> crtscts
>>> lock
>>> hide-password
>>> modem
>>> proxyarp
>>> lcp-echo-interval 30
>>> lcp-echo-failure 4
>>> noipx
>>>
>>> In case of a message like:
>>> Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
>>> see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
>>>
>>> Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0 wlan0
>>> wmaster0
>>> Which can interfere with Browser naviagation.
>>>
>>> Don't worry about the following, it is for experts should trouble
>>> shooting
>>> be necessary.
>>> ==========================================================
>>>
>>> Checking for modem support lines:
>>> --------------------------------------
>>> /device/modem symbolic link: lrwxrwxrwx 1 root root 6 2009-07-20
>>> 17:19
>>> /dev/modem -> ttySL0
>>> slmodemd created symbolic link /dev/ttySL0: lrwxrwxrwx 1 root root 10
>>> 2009-07-20 17:19 /dev/ttySL0 -> /dev/pts/2
>>> Within /etc/udev/ files:
>>>
>>> Within /etc/modprobe.conf files:
>>> /etc/modprobe.d/blacklist-modem.conf:# Uncomment these entries in order
>>> to
>>> blacklist unwanted modem drivers
>>> /etc/modprobe.d/blacklist-modem.conf:# blacklist snd-atiixp-modem
>>> /etc/modprobe.d/blacklist-modem.conf:# blacklist snd-via82xx-modem
>>> /etc/modprobe.d/alsa-base.conf:options snd-atiixp-modem index=-2
>>> /etc/modprobe.d/alsa-base.conf:options snd-via82xx-modem index=-2
>>> Within any ancient /etc/devfs files:
>>>
>>> Within ancient kernel 2.4.n /etc/module.conf files:
>>>
>>> --------- end modem support lines --------
>>>
>>>
>>>
>>
>
