Ryan, Providing your computer running Linux does emit audible sounds AND your modem is actually connected to the phone line, you should at least hear it attempting to dial your ISP phone number. Kind regards, - http://vouters.dyndns.org:8080/ Philippe Vouters (Fontainebleau/France) Le mardi 30 juin 2009 à 21:02 +0200, Philippe Vouters a écrit : > >From the URL link I sent you, I can read the following: > ATM Speaker control > M0 Speaker always off > M1 Speaker on until carrier detected > M2 Speaker always on > M3 Speaker on only while answering > > So replace in your /etc/wvdial.conf the line: > Init3 = ATM1L3 > by > Init3=ATM2L3 > and you ought to hear a sound from your modem board. Prior to this > suggested change, make sure your computer is indeed able to produce > audible sounds. For this, just introduce your preferred music CD into > your CD/DVD computer peripheral. > - > http://vouters.dyndns.org:8080/ > Philippe Vouters (Fontainebleau/France) > > > Le mardi 30 juin 2009 à 19:48 +0100, Ryan a écrit : > > Philippe. > > > > I changed /etc/wvdial.conf so it includes the line: > > [Modem0] > > > > I do not use a country code when dialling the phone number (or so the > > Windows XP settings lead me to believe). > > > > Next, I changed (with some difficulty; I had to use the command $ sudo nano > > /etc/init.d/537_boot) /etc/init.d/537_boot so the code appears like: > > > > case "$1" in > > start | b) > > if ! ( modprobe $serial sound_enabled=1); then > > { > > if ! ( insmod -f $serial ); then > > { > > > > And rebooted my computer. Then I ran wvdial again with still the same > > result: > > > > ryan@Ryan:~$ sudo wvdial > > [sudo] password for ryan: > > --> WvDial: Internet dialer version 1.55 > > --> Initializing modem. > > --> Sending: ATZ > > ATZ > > OK > > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > > OK > > --> Sending: ATM1L3 > > ATM1L3 > > OK > > --> Modem initialized. > > --> Sending: ATDT08440575000 > > --> Waiting for carrier. > > ATDT08440575000 > > NO DIALTONE > > --> No dial tone. > > --> Disconnecting at Tue Jun 30 19:39:45 2009 > > > > And I heard no noises from the modem. > > > > > > Can you help further? > > Ryan > > > > > > ----- Original Message ----- > > From: Philippe Vouters > > To: Ryan > > Cc: Marvin Stodolsky > > Sent: Tuesday, June 30, 2009 6:39 PM > > Subject: Re: can you try this coredrv.c ? > > > > > > Ryan, > > > > Your /etc/wvdial.conf should looks like this, with ATDT: > > > > [Modem0] > > Modem = /dev/modem > > Baud = 115200 > > SetVolume = 3 > > Dial Command = ATDT > > Init1 = ATZ > > Init2 = AT+GCI=3D > > Init3 = ATM1L3 > > Carrier Check = no > > FlowControl = CRTSCTS > > #Stupid Mode = yes > > [Dialer Defaults] > > Username = [MyUserNameIsHere] > > Password = [MyPasswordIsHere] > > Phone = 08440575000 > > Init1 = ATZ > > Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > > Inherits = Modem0 > > > > Without [Modem0], you will not "Inherits = Modem0" > > > > Next AT+CGI=3D : 3D is the code for France. Refer to the readme.txt file > > in intel-536-537/ directory for the correct code for your country. > > > > Next as you have set "Init3 = ATM1L3", you might edit depending on your > > Linux distribution either /etc/init.d/537_boot or /etc/rc.d/init.d/537_boot > > and modify > > the shell code so it appears the following: > > > > case "$1" in > > start | b) > > if ! ( modprobe $serial sound_enabled=1); then > > { > > if ! ( insmod -f $serial ); then > > { > > > > Note that you ought to only do this to troubleshoot your modem and in order > > to > > listen to the noise it produces. Permanently keeping this modification might > > prevent you in the future from listening to your favorite music using your > > Linux computer > > meanwhile being connected on Internet. > > > > Doing the above will help you ear check the NO DIALTONE error message > > produced by your modem > > in your phone line configuration. Please note the above does not apply to a > > 536EP Intel's modem, > > but is entirely specific to the 537 modems family. > > > > Hoping this gives you some hints on what to do to troubleshoot the problem. > > - > > http://vouters.dyndns.org:8080/ > > Philippe Vouters (Fontainebleau/France) > > > >
