Re: Chris Sparnicht, USA kernel 2.6.26-2-686

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Marvin,

Well, I think we're closer - thanks again.
I followed your suggestions and tried a number of different things.
I added the correct phone, user and pass in the wvdial.conf.
I changed the path to /dev/537 in Gnome PPP.
More screen results below.

===== terminal results =====

rod@rod-desktop:~$ sudo ln -s /dev/537  /dev/ttySpctel
[sudo] password for rod:
rod@rod-desktop:~$ sudo wvdialconf
Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ttyS2<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS2<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS2<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ttyS3<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS3<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS3<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
ttySpctel<*1>: ATQ0 V1 E1 -- OK
ttySpctel<*1>: ATQ0 V1 E1 Z -- OK
ttySpctel<*1>: ATQ0 V1 E1 S0=0 -- OK
ttySpctel<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttySpctel<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttySpctel<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttySpctel<*1>: Modem Identifier: ATI -- OK
ttySpctel<*1>: Speed 4800: AT -- OK
ttySpctel<*1>: Speed 9600: AT -- OK
ttySpctel<*1>: Speed 19200: AT -- OK
ttySpctel<*1>: Speed 38400: AT -- OK
ttySpctel<*1>: Speed 57600: AT -- OK
ttySpctel<*1>: Speed 115200: AT -- OK
ttySpctel<*1>: Speed 230400: AT -- OK
ttySpctel<*1>: Speed 460800: AT -- OK
ttySpctel<*1>: Max speed is 460800; that should be safe.
ttySpctel<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK

Found a modem on /dev/ttySpctel.
Modem configuration written to /etc/wvdial.conf.
ttySpctel<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
rod@rod-desktop:~$ nano /etc/wvdial.conf
rod@rod-desktop:~$ sudo !!
sudo nano /etc/wvdial.conf
rod@rod-desktop:~$ man wvdial
rod@rod-desktop:~$ poff
/usr/bin/poff: No pppd is running.  None stopped.
rod@rod-desktop:~$ wvdial stop
--> WvDial: Internet dialer version 1.60
--> Warning: section [Dialer stop] does not exist in wvdial.conf.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Configuration does not specify a valid phone number.
--> Configuration does not specify a valid login name.
--> Configuration does not specify a valid password.
rod@rod-desktop:~$ wvdial
--> WvDial: Internet dialer version 1.60
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Configuration does not specify a valid phone number.
--> Configuration does not specify a valid login name.
--> Configuration does not specify a valid password.
rod@rod-desktop:~$


===== gnome log =====
--> Ignoring malformed input line: ";Do NOT edit this file by hand!"
--> WvDial: Internet dialer version 1.60
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Sending: ATM1L3DT(###) 621-4801
--> Waiting for carrier.
ATM1L3DT(###) 621-4801
NO DIALTONE
--> No dial tone.
--> Disconnecting at Thu May  7 22:17:34 2009


Marvin Stodolsky wrote:
> Chris,
>
> Evidently your wvdialconf is not testing /dev/modem
> So set a symbolic link
> $ sudo ln -s /dev/537  /dev/ttySpctel
> Then again try
> $ sudo wvdialconf
>
> If the modem is found:
> $ sudo gedit  /etc/wvdial.conf
> entering your personal info and removing the symbols ; < >
>
> Also if either the configuration tools for KPPP or  gnomeppp while
> allow you to specify /dev/537 as the port, you can likely use them
> too.
>
> MarvS
>
> On Thu, May 7, 2009 at 8:41 PM,  <chris@xxxxxxxxxxx> wrote:
>> Marvin,
>>
>> Hi, and thanks once more.
>>
>> See 'results - wvdial.conf' below.
>> It appears there was already a symlink from /dev/537 to /dev/modem.
>> The wiki referred to in the results is no longer there.
>>
>> Attempts with Gnome PPP also give odd results, even though everything
>> has
>> been set properly as far as I can tell. See 'results - Gnome PPP' below.
>> Gnome PPP also has a nasty habit of freezing the desktop. I have to
>> reboot. Bummer.
>>
>> Chris
>>
>> ===== results - wvdial.conf =====
>> rod@rod-desktop:~$ sudo wvdialconf
>> [sudo] password for rod:
>> Editing `/etc/wvdial.conf'.
>>
>> Scanning your serial ports for a modem.
>>
>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
>> ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
>> ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
>> ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
>> ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
>> ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
>> ttyS2<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
>> ttyS2<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
>> ttyS2<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
>> ttyS3<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
>> ttyS3<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
>> ttyS3<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
>>
>>
>> Sorry, no modem was detected!  Is it in use by another program?
>> Did you configure it properly with setserial?
>>
>> Please read the FAQ at http://open.nit.ca/wiki/?WvDial
>>
>> ===== results - Gnome PPP =====
>> --> Ignoring malformed input line: ";Do NOT edit this file by hand!"
>> --> WvDial: Internet dialer version 1.60
>> --> Initializing modem.
>> --> Sending: ATZ
>> ATZ
>> OK
>> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
>> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
>> OK
>> --> Modem initialized.
>> --> Please enter password (or empty password to stop):
>>
>>
>>




[Index of Archives]     [Linux Media Development]     [Asterisk]     [DCCP]     [Netdev]     [X.org]     [Xfree86]     [Fedora Women]     [Linux USB]

  Powered by Linux