Hello,
i tried, to use the Xircom MiniPCI modem. I used some different martian-modem
packages (20071011,200800617,20080625) and Linux kernel
versions(2.6.22,2.6.25,2.6.27), but nothing works. That MiniPCI
Ethernet/modem card runs on a other T21 with kernel 2.4.18 and
martian-modem-20061203 without problems.
I can compile the package and start martian_modem, but wvdial can not find a
modem device on /dev/ttySM0. Can anybody help me?
Thanks
rudi
here are some system messages:
------------syslog:
Apr 10 14:03:22 t21 kernel: martian loaded - 20080620
Apr 10 14:03:22 t21 kernel: ACPI: PCI Interrupt 0000:00:03.1[A] -> Link
[LNKC] -> GSI 9 (level, low) -> IRQ 9
Apr 10 14:03:22 t21 kernel: martian: added device 115d:c BaseAddress = 0x1840,
CommAddres = 0x0, irq = 9
Apr 10 14:05:19 t21 kernel: martian: debug option is enabled.
Apr 10 14:05:19 t21 kernel: martian_modem is attached.
Apr 10 14:06:22 t21 kernel: martian_modem is detached
Apr 10 14:06:22 t21 kernel: martian: Core vars:
Apr 10 14:06:22 t21 kernel: martian: Variable Value
Apr 10 14:06:22 t21 kernel: martian:BaseAddress 0x1840
Apr 10 14:06:22 t21 kernel: martian:BaseAddress2 0x1842
Apr 10 14:06:22 t21 kernel: martian:BaseAddressIndex 0x1840
Apr 10 14:06:22 t21 kernel: martian:BaseValue 0x0
Apr 10 14:06:22 t21 kernel: martian:BaseAddressData 0x1841
Apr 10 14:06:22 t21 kernel: martian:dp_bamil_rd7 0xff
Apr 10 14:06:22 t21 kernel: martian:x_dsp_mars 0
Apr 10 14:06:22 t21 kernel: "martian_dev": dce_rx: 2048x2 b | u16 -> (0, 0)
Apr 10 14:06:22 t21 kernel: "martian_dev": pdm_rx: 1200x1 u8 -> (0, 0)
Apr 10 14:06:22 t21 kernel: "martian_dev": dce_tx: 1024x2 b | u16 -> (0, 0)
-----------command line 1:
t21:~ # modprobe martian_dev
t21:~ # martian_modem --debug=5
martian: D2: source stamp `20080620'
martian: D2: arguments "--debug=5"
martian: D2: configuration: debuglevel=5
martian % 18.986: D3: check tsc status 0
martian: D2: TSC: 746.784000 MHz
martian: D2: Kernel module stamp `20080620'
martian: D2: ld: Relocating isr symbols
martian: D2: Notifying kernel READY
martian: D2: isr: thread started (tid = 11656)
martian: D2: isr: scheduler: policy 1, priority 99
martian: D2: isr thread launched
martian: D2: set timer for thread
martian: D2: servicing thread started (tid = 11657)
martian: D2: set timer for thread
martian: D2: virtirq: set handler
martian: D2: pty: checking file /dev/ttySM0
martian: D2: pty: stat: No such file or directory
martian: D2: pty: using /dev/pts/2
martian: D2: servicing thread launched
martian: info: Your port is /dev/ttySM0
martian: D2: worker thread going into loop (tid = 11643)
martian: D2: /dev/martian already exists
martian: D1: got a client
martian: info: session: Started Fri Apr 10 14:06:12 2009
{nnnnnnnnnnnnnnnnnnnpty<11643>
}
martian % 12.566: D3: monitor: io_uart_msr: +33 -0, io_uart_status: +33a -0,
x_modem_state: 0->1, x_line_rate: NA->14400
{cinnnnnnnnnnnnnnnnnnnnpty<11643>
cinnnnnnnnnnnnnnnnnnpty<11643>
cinnnnnnnnnnnnnnnnnnnpty<11643>
cinnnnnnnnnnnnnnnnnnnnpty<11643>
cinnnnnnnnnnnnnnnnnnnpty<11643>
cinnnnnnnnnnnnnnnnnnnnpty<11643>
cinnnnnnnnnnnnnnnnnnnnpty<11643>
^Ccinnnnnnn}
martian: D2: Intr in thread <11643>
martian: D: Irq: string bb|bbbbbbb, pulses 922
martian: D: Irq: b: 307, n: 615, f: 0, i: 0, o: 0
martian: D: interrupts: ring=0, stream=0 (dcp=0, trx=0), bit3=0
martian: D: calls: tx: 0, rx: 0, pdm; bytes: tx: 0, rx: 0, pdm: 0
martian: D: mcb: calls: tx: 0, rx: 0, pdm: 0;bytes: tx: 0, rx: 0, pdm: 0
martian: D: overrun: dce = 0, pdm = 0; incorrespondence: tx = 0, rx = 0, pdm =
0
martian: info: redefined calls
martian: info: regr 0
martian: info: regw 13
martian: info: regao 1
martian: info: cmd 1
martian: info: longcmd 1
martian: info: read 2
martian: info: write 0
martian: info: dload 0
martian: info: writew 0
martian: info: writeb 0
martian: info: Bye.
---------command line 2
t21:~ # wvdialconf ./wvdial.conf
Editing `./wvdial.conf'.
Scanning your serial ports for a modem.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S1 S2 S3
ttyS4<Info>: No such device or address
Modem Port Scan<*1>: S4
ttyS5<Info>: No such device or address
Modem Port Scan<*1>: S5
ttyS6<Info>: No such device or address
Modem Port Scan<*1>: S6
ttyS7<Info>: No such device or address
Modem Port Scan<*1>: S7
WvModem<*1>: Cannot get information for serial port.
ttySM0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttySM0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttySM0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Sorry, no modem was detected! Is it in use by another program?
Did you configure it properly with setserial?
Please read the FAQ at http://open.nit.ca/wiki/?WvDial
If you still have problems, send mail to <wvdial-list@xxxxxxxxxxxx>.
