After a long not using the LT Modem on my Laptop i took a look on the aktual Driver. It works partial not correct using Fax ( hylafax ). System is an old Gericom M6T Notebook ( PIII 1.2ghz 1G of Ram ) Systemsoft ist Opensuse 11.0 with an 2.6.25 Kernel. Problems while compiling: the direktory asm wasn't find, so i create an link to /usr/src/linux/include/asm/asm-x86 now compiling worked - sucess... . Test with Hylafax on my local Telephoneinstallation does connect my Faxreciever, but the Fax ( Sharp UX-510 Standart Faxdevice ) stopped with an Error Code 01 and the logs of hylafax also reports an Error. File /var/spool/fax/log/ attached I don't need the ltmodem that much anymore, but it would be nice to get it working ;-) Greetings from Germany
Oct 12 12:36:29.56: [ 4146]: SESSION BEGIN 000000003 494513892253 Oct 12 12:36:29.56: [ 4146]: HylaFAX (tm) Version 4.4.0 Oct 12 12:36:29.56: [ 4146]: SEND FAX: JOB 1 DEST 3892253 COMMID 000000003 DEVICE '/dev/ttySM0' FROM 'Bernd Stuht <bernd@xxxxxxxxxxxxxxxxx>' USER bernd Oct 12 12:36:29.56: [ 4146]: <-- [12:AT+FCLASS=1\r] Oct 12 12:36:29.57: [ 4146]: --> [2:OK] Oct 12 12:36:29.57: [ 4146]: MODEM set XON/XOFF/FLUSH: input ignored, output disabled Oct 12 12:36:29.57: [ 4146]: DIAL 3892253 Oct 12 12:36:29.57: [ 4146]: <-- [12:ATDT3892253\r] Oct 12 12:36:42.80: [ 4146]: --> [7:CONNECT] Oct 12 12:36:44.91: [ 4146]: --> [2:OK] Oct 12 12:36:44.91: [ 4146]: REMOTE NSF "00 00 31 00 CE B8 C4 80 11 85 0D DD 00 00 DD DD 00 00 DD DD 00 00 00 00 00 00 00 00 ED 22 B0 00 00 A4 00" Oct 12 12:36:44.91: [ 4146]: NSF remote fax equipment: Sharp/Olivetti Oct 12 12:36:44.91: [ 4146]: <-- [9:AT+FRH=3\r] Oct 12 12:36:44.93: [ 4146]: --> [7:CONNECT] Oct 12 12:36:45.64: [ 4146]: --> [2:OK] Oct 12 12:36:45.64: [ 4146]: REMOTE CSI "+49 451 3892254" Oct 12 12:36:45.64: [ 4146]: <-- [9:AT+FRH=3\r] Oct 12 12:36:45.66: [ 4146]: --> [7:CONNECT] Oct 12 12:36:46.00: [ 4146]: --> [2:OK] Oct 12 12:36:46.00: [ 4146]: REMOTE best rate 9600 bit/s Oct 12 12:36:46.00: [ 4146]: REMOTE max A4 page width (215 mm) Oct 12 12:36:46.00: [ 4146]: REMOTE max unlimited page length Oct 12 12:36:46.00: [ 4146]: REMOTE best vres 15.4 line/mm Oct 12 12:36:46.00: [ 4146]: REMOTE format support: MH, MR, MMR Oct 12 12:36:46.00: [ 4146]: REMOTE supports T.30 Annex A, 256-byte ECM Oct 12 12:36:46.00: [ 4146]: REMOTE best 20 ms, 10 ms/scanline Oct 12 12:36:46.00: [ 4146]: USE 9600 bit/s Oct 12 12:36:46.00: [ 4146]: USE error correction mode Oct 12 12:36:46.00: [ 4146]: SEND file "docq/cover1;00" Oct 12 12:36:46.00: [ 4146]: USE A4 page width (215 mm) Oct 12 12:36:46.00: [ 4146]: USE unlimited page length Oct 12 12:36:46.00: [ 4146]: USE 3.85 line/mm Oct 12 12:36:46.00: [ 4146]: USE 2-D MMR Oct 12 12:36:46.00: [ 4146]: USE 0 ms/scanline Oct 12 12:36:46.00: [ 4146]: SEND training at v.29 9600 bit/s Oct 12 12:36:46.00: [ 4146]: <-- [9:AT+FRS=7\r] Oct 12 12:36:46.08: [ 4146]: --> [2:OK] Oct 12 12:36:46.08: [ 4146]: <-- [9:AT+FTH=3\r] Oct 12 12:36:46.97: [ 4146]: --> [7:CONNECT] Oct 12 12:36:46.97: [ 4146]: <-- data [23] Oct 12 12:36:46.97: [ 4146]: <-- data [2] Oct 12 12:36:46.98: [ 4146]: --> [7:CONNECT] Oct 12 12:36:46.98: [ 4146]: <-- data [7] Oct 12 12:36:46.98: [ 4146]: <-- data [2] Oct 12 12:36:48.09: [ 4146]: --> [2:OK] Oct 12 12:36:48.09: [ 4146]: <-- [9:AT+FTS=7\r] Oct 12 12:36:48.40: [ 4146]: MODEM READ ERROR: errno 5 Oct 12 12:36:48.40: [ 4146]: --> [0:] Oct 12 12:36:48.40: [ 4146]: MODEM <Empty line> Oct 12 12:36:48.40: [ 4146]: Stop and wait failure (modem on hook) Oct 12 12:36:48.40: [ 4146]: <-- [9:AT+FRS=7\r] Oct 12 12:36:48.40: [ 4146]: MODEM READ ERROR: errno 5 Oct 12 12:36:48.40: [ 4146]: --> [0:] Oct 12 12:36:48.40: [ 4146]: MODEM <Empty line> Oct 12 12:36:48.40: [ 4146]: Failure to receive silence (synchronization failure). Oct 12 12:36:48.40: [ 4146]: <-- [9:AT+FTH=3\r] Oct 12 12:36:48.40: [ 4146]: MODEM READ ERROR: errno 5 Oct 12 12:36:48.40: [ 4146]: --> [0:] Oct 12 12:36:48.40: [ 4146]: MODEM input buffering enabled Oct 12 12:36:49.40: [ 4146]: <-- [5:ATH0\r] Oct 12 12:36:49.40: [ 4146]: MODEM WRITE ERROR: errno 5 Oct 12 12:36:49.40: [ 4146]: MODEM set DTR OFF Oct 12 12:36:49.40: [ 4146]: MODEM set baud rate: 0 baud (flow control unchanged) Oct 12 12:36:49.40: [ 4146]: MODEM setBaudRate::tcgetattr: Input/output error Oct 12 12:36:49.40: [ 4146]: SESSION END
