Thanks Marvin,
dmesg.txt attached.
Marvin Stodolsky wrote:
John
RE: [ 13.814704] ACPI: PCI interrupt for device 0000:00:02.6 disabled
under Linux version 2.6.24-19-generic
Do:
$ dmesg >> dmesg.txt
$ lsmod >> dmesg.txt
and send us the dmesg.txt.
MarvS
On Sun, Oct 5, 2008 at 12:18 AM, Antonio Olivares
<olivares14031@xxxxxxxxx> wrote:
John,
This is a second case that returns something like this, I would suspect
that the output
/*
The /proc/asound/pcm file reports:
-----------------------
00-01: Intel ICH - MIC ADC : SiS SI7012 - MIC ADC : capture 1
00-00: Intel ICH : SiS SI7012 : playback 1 : capture 1
*/
should have output somewhere a Modem part and it did not. Might be
something different. I guess it would be wise to wait for Marv's advice on
this one. Unless the part
/*
Modem interrupt assignment and sharing:
18: 495 IO-APIC-fasteoi SiS SI7012
--- Bootup diagnostics for card in PCI slot 00:02.6
----
[ 12.180926] ACPI: PCI Interrupt 0000:00:02.6[C]
GSI 18 (level,
low) -> IRQ 18
[ 13.814697] ACPI: PCI Interrupt 0000:00:02.6[C]
-> GSI 18 (level,
low) -> IRQ 18
[ 13.814704] ACPI: PCI interrupt for device
0000:00:02.6 disabled
The PCI slot 00:02.6 of the modem card may be disabled
early in
a bootup process, but then enabled later. If modem
drivers load
but the modem is not responsive, read DOCs/Bootup.txt
about possible fixes.
Send dmesg.txt along with ModemData.txt to
discuss@xxxxxxxxxxxxx
if help is needed.
*/
is the culprit. Nonetheless the Modem part should appear to be supported
by slmodemd. Hope this gets to Marv and he'll give you better advice.
Regards,
Antonio
--- On Sat, 10/4/08, John McLachlan <john.mcl@xxxxxxxxxx> wrote:
From: John McLachlan <john.mcl@xxxxxxxxxx>
Subject: Re: John McLachlan New Zealand Kernel 2.6.24-19-generic
To: "Antonio Olivares" <olivares14031@xxxxxxxxx>
Cc: DISCUSS@xxxxxxxxxxxxx
Date: Saturday, October 4, 2008, 9:07 PM
Thanks Antonio,
Extracted OK, installed OK, but setup of slmodemd gives the
following
response (tried also with sudo ...). Any further ideas.
John.
john@John-Laptop:~/SLMODEMD.gcc4.2$ slmodemd -c 7e --alsa
modem:1
error: mixer setup: attach hw:1 error: No such file or
directory
ALSA lib conf.c:3952:(snd_config_expand) Unknown parameters
1
ALSA lib pcm.c:2145:(snd_pcm_open_noupdate) Unknown PCM
modem:1
error: alsa setup: cannot open playback device
'modem:1': Invalid argument
error: cannot setup device `modem:1'
Antonio Olivares wrote:
John,
scanModem recommends:
Support type needed or chipset: slmodemd
An ALSA (Advanced Linux Sound Architecture) modem
driver: snd-intel8x0m
provides Low Level support enabling contact with the
modem hardware.
For all BUT Conexant chip soft modems (using hsfmodem
software)
complementary High Level support is through a
Smartlink utility: slmodemd
Download from
http://linmodems.technion.ac.il/packages/smartlink/
the package SLMODEMD.gcc4.2.tar.gz having a compiled
slmodemd. Unpack
under Linux with:
$ tar zxf SLMODEMD.gcc4.2.tar.gz
and read instructions therein. But briefly, the modem
is setup with command:
sudo slmodemd -c YOUR_COUNTRY --alsa modem:1
reporting dynamic creation of ports:
/dev/ttySL0 --> /dev/pts/N , with N some number
Read DOCs/Smartlink.txt and Modem/DOCs/YourSystem.txt
for follow
through guidance.
But, if the modem is nonresponsive you need:
Modem interrupt assignment and sharing:
18: 495 IO-APIC-fasteoi SiS SI7012
--- Bootup diagnostics for card in PCI slot 00:02.6
----
[ 12.180926] ACPI: PCI Interrupt 0000:00:02.6[C]
-> GSI 18 (level,
low) -> IRQ 18
[ 13.814697] ACPI: PCI Interrupt 0000:00:02.6[C]
-> GSI 18 (level,
low) -> IRQ 18
[ 13.814704] ACPI: PCI interrupt for device
0000:00:02.6 disabled
The PCI slot 00:02.6 of the modem card may be disabled
early in
a bootup process, but then enabled later. If modem
drivers load
but the modem is not responsive, read DOCs/Bootup.txt
about possible fixes.
Send dmesg.txt along with ModemData.txt to
discuss@xxxxxxxxxxxxx
if help is needed.
Regards,
Antonio
On Fri, Oct 3, 2008 at 6:29 AM, John McLachlan
<john.mcl@xxxxxxxxxx> wrote:
Hi,
Recent installation of Hardy.
Trying to get modem working to enable faxing.
Conversion from XP system Acer Aspire 5002WLMI AMD
Turion4 1.6HGz system.
Any help would be appreciated. Tried various bits
I found on the web to no
avail.
John McL.
Modemdata.txt:
-------------------------- System information
----------------------------
CPU=i686, Linux version 2.6.24-19-generic
(buildd@terranova) (gcc version
4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Wed Aug 20
22:56:21 UTC 2008
scanModem update of: 2008_08_26
There are no blacklisted modem drivers in
/etc/modprobe* files
Attached USB devices are:
ID 045e:00b9 Microsoft Corp. Wireless Optical
Mouse 3.0
USB modems not recognized
For candidate card in slot 00:02.6, firmware
information and bootup
diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- ---------
--------------
00:02.6 1039:7013 1025:0083 Modem:
Silicon Integrated Systems [SiS]
AC'97 Modem Controller
Modem interrupt assignment and sharing:
18: 495 IO-APIC-fasteoi SiS SI7012
--- Bootup diagnostics for card in PCI slot
00:02.6 ----
[ 12.180926] ACPI: PCI Interrupt 0000:00:02.6[C]
-> GSI 18 (level, low) ->
IRQ 18
[ 13.814697] ACPI: PCI Interrupt 0000:00:02.6[C]
-> GSI 18 (level, low) ->
IRQ 18
[ 13.814704] ACPI: PCI interrupt for device
0000:00:02.6 disabled
The PCI slot 00:02.6 of the modem card may be
disabled early in
a bootup process, but then enabled later. If
modem drivers load
but the modem is not responsive, read
DOCs/Bootup.txt about possible fixes.
Send dmesg.txt along with ModemData.txt to
discuss@xxxxxxxxxxxxx
if help is needed.
===== Advanced Linux Sound Architecture (ALSA)
diagnostics =====
The ALSA packages provide audio support and also
drivers for some modems.
ALSA diagnostics are written during bootup to
/proc/asound/ folders.
The ALSA verion is 1.0.16
The modem cards detected by "aplay -l"
are: None
The /proc/asound/pcm file reports:
-----------------------
00-01: Intel ICH - MIC ADC : SiS SI7012 - MIC ADC
: capture 1
00-00: Intel ICH : SiS SI7012 : playback 1 :
capture 1
about /proc/asound/cards:
------------------------
0 [SI7012 ]: ICH - SiS SI7012
SiS SI7012 with ALC203 at irq
18
=== Finished firmware and bootup diagnostics, next
deducing cogent software.
===
Predictive diagnostics for card in bus 00:02.6:
Modem chipset detected on
NAME="Modem: Silicon Integrated Systems [SiS]
AC'97 Modem Controller "
CLASS=0703
PCIDEV=1039:7013
SUBSYS=1025:0083
IRQ=18
SOFT=1039:7013.MC97
CodecArchived=SIL2f
IDENT=slmodemd
SLMODEMD_DEVICE=modem:1
Driver=snd-intel8x0m
For candidate modem in: 00:02.6
0703 Modem: Silicon Integrated Systems [SiS]
AC'97 Modem Controller
Primary device ID: 1039:7013
Subsystem PCI_id 1025:0083
Softmodem codec or chipset from diagnostics:
from Archives:
SIL2f
Support type needed or chipset: slmodemd
An ALSA (Advanced Linux Sound Architecture) modem
driver: snd-intel8x0m
provides Low Level support enabling contact with
the modem hardware.
For all BUT Conexant chip soft modems (using
hsfmodem software)
complementary High Level support is through a
Smartlink utility: slmodemd
Download from
http://linmodems.technion.ac.il/packages/smartlink/
the package SLMODEMD.gcc4.2.tar.gz having a
compiled slmodemd. Unpack under
Linux with:
$ tar zxf SLMODEMD.gcc4.2.tar.gz
and read instructions therein. But briefly, the
modem is setup with command:
sudo slmodemd -c YOUR_COUNTRY --alsa modem:1
reporting dynamic creation of ports:
/dev/ttySL0 --> /dev/pts/N , with N some
number
Read DOCs/Smartlink.txt and
Modem/DOCs/YourSystem.txt for follow through
guidance.
----------------end Softmodem section
--------------
Writing DOCs/Smartlink.txt
============ end Smartlink section
=====================
Completed candidate modem analyses.
The base of the UDEV device file system is:
/dev/.udev
Versions adequately match for the compiler
installed: 4.2.3
and the compiler used in kernel
assembly: 4.2.3
Minimal compiling resources appear complete:
make utility - /usr/bin/make
Compiler version 4.2
linuc_headers base folder
/lib/modules/2.6.24-19-generic/build
However some compilations and executable functions
may need additional
files,
in the FileNames.h (so called kernel
"h"eaders) collection installed in
/usr/include/ .
For martian_modem, additional required packages
are needed. The also
required headers of package libc6 are commonly
installed by default.
Compiling hsfmodem drivers does require
linux-libc-dev and libc6-dev
packages, for kernels 2.6.24 and later versions.
In not included on your install CD, search for
them at
http://packages.ubuntu.com
or comparable Repository for other Linux distros.
When compiling ALSA drivers, the utility
"patch" will also be needed.
If a driver compilation fails, with message
including some lack of some
FileName.h (stdio.h for example), then
Some additional kernel-header files need
installation to /usr/include. The
minimal additional packages are libc6-dev
and any of its dependents, under Ubuntu
linux-libc-dev
If an alternate ethernet connection is available,
$ apt-get update
$ apt-get -s install linux-kernel-devel
will install needed packages.
For Debian/Ubuntu related distributions, run the
following command to
display the needed package list:
Otherwise packages have to be found through
http://packages.ubuntu.com
Once downloaded and transferred into a Linux
partition,
they can be installed alltogether with:
$ sudo dpkg -i *.deb
Checking pppd properties:
-rwsr-xr-- 1 root dip 269256 2007-10-05 08:57
/usr/sbin/pppd
In case of an "error 17" "serial
loopback" problem, see:
http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html
To enable dialout without Root permission do:
$ su - root (not for Ubuntu)
sudo chmod a+x /usr/sbin/pppd
or under Ubuntu related Linuxes
sudo chmod a+x /usr/sbin/pppd
Checking settings of: /etc/ppp/options
asyncmap 0
noauth
crtscts
lock
hide-password
modem
proxyarp
lcp-echo-interval 30
lcp-echo-failure 4
noipx
In case of a message like:
Warning: Could not modify /etc/ppp/pap-secrets:
Permission denied
see
http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
Read Modem/DOCs/YourSystem.txt concerning other
COMM channels: eth0 wlan0
wmaster0
Which can interfere with Browser naviagation.
Don't worry about the following, it is for
experts should trouble shooting
be necessary.
==========================================================
Checking for modem support lines:
--------------------------------------
/device/modem symbolic link: slmodemd created
symbolic link
/dev/ttySL0: Within /etc/udev/ files:
Within /etc/modprobe.conf files:
/etc/modprobe.d/blacklist-modem:# Uncomment these
entries in order to
blacklist unwanted modem drivers
/etc/modprobe.d/blacklist-modem:# blacklist
snd-atiixp-modem
/etc/modprobe.d/blacklist-modem:# blacklist
snd-via82xx-modem
/etc/modprobe.d/alsa-base:options snd-atiixp-modem
index=-2
/etc/modprobe.d/alsa-base:options
snd-via82xx-modem index=-2
Within any ancient /etc/devfs files:
Within ancient kernel 2.4.n /etc/module.conf
files:
--------- end modem support lines --------
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.24-19-generic (buildd@terranova) (gcc
version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Wed Aug 20 22:56:21 UTC 2008
(Ubuntu 2.6.24-19.41-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
[ 0.000000] BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000001bef0000 (usable)
[ 0.000000] BIOS-e820: 000000001bef0000 - 000000001befa000 (ACPI data)
[ 0.000000] BIOS-e820: 000000001befa000 - 000000001bf00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000001bf00000 - 0000000020000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 446MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f7fd0
[ 0.000000] Entering add_active_range(0, 0, 114416) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 114416
[ 0.000000] HighMem 114416 -> 114416
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 114416
[ 0.000000] On node 0 totalpages: 114416
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 861 pages used for memmap
[ 0.000000] Normal zone: 109459 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F7F60 checksum 0
[ 0.000000] ACPI: RSDP 000F7F60, 0014 (r0 PTLTD )
[ 0.000000] ACPI: RSDT 1BEF61D6, 0034 (r1 PTLTD RSDT 6040000 LTP
0)
[ 0.000000] ACPI: FACP 1BEF9E5F, 0074 (r1 SiS 755F 6040000 PTL
F4240)
[ 0.000000] ACPI: DSDT 1BEF620A, 3C55 (r1 PTLTD 755 6040000 MSFT
100000E)
[ 0.000000] ACPI: FACS 1BEFAFC0, 0040
[ 0.000000] ACPI: SSDT 1BEF9ED3, 00B5 (r1 PTLTD POWERNOW 6040000 LTP
1)
[ 0.000000] ACPI: APIC 1BEF9F88, 0050 (r1 PTLTD APIC 6040000
LTP 0)
[ 0.000000] ACPI: BOOT 1BEF9FD8, 0028 (r1 PTLTD $SBFTBL$ 6040000 LTP
1)
[ 0.000000] ACPI: DMI detected: Acer
[ 0.000000] ACPI: PM-Timer IO Port: 0x8008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:4 APIC version 16
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI
0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ11 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 30000000 (gap:
20000000:dff00000)
[ 0.000000] swsusp: Registered nosave memory region: 000000000009f000 -
00000000000a0000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000a0000 -
00000000000dc000
[ 0.000000] swsusp: Registered nosave memory region: 00000000000dc000 -
0000000000100000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total
pages: 113523
[ 0.000000] Kernel command line:
root=UUID=afa07e9b-b58f-4370-bc14-9bafc21a73ac ro pci=routeirq quiet splash
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Detected 1600.075 MHz processor.
[ 11.783187] Console: colour VGA+ 80x25
[ 11.783191] console [tty0] enabled
[ 11.783580] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 11.783897] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 11.794305] Memory: 441604k/457664k available (2177k kernel code, 15452k
reserved, 1006k data, 368k init, 0k highmem)
[ 11.794315] virtual kernel memory layout:
[ 11.794316] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB)
[ 11.794317] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 11.794319] vmalloc : 0xdc800000 - 0xff7fe000 ( 559 MB)
[ 11.794320] lowmem : 0xc0000000 - 0xdbef0000 ( 446 MB)
[ 11.794321] .init : 0xc0421000 - 0xc047d000 ( 368 kB)
[ 11.794323] .data : 0xc03204c4 - 0xc041bdc4 (1006 kB)
[ 11.794324] .text : 0xc0100000 - 0xc03204c4 (2177 kB)
[ 11.794328] Checking if this processor honours the WP bit even in
supervisor mode... Ok.
[ 11.794365] SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4,
CPUs=1, Nodes=1
[ 11.874266] Calibrating delay using timer specific routine.. 3202.13
BogoMIPS (lpj=6404278)
[ 11.874294] Security Framework initialized
[ 11.874300] SELinux: Disabled at boot.
[ 11.874316] AppArmor: AppArmor initialized
[ 11.874320] Failure registering capabilities with primary security
module.
[ 11.874329] Mount-cache hash table entries: 512
[ 11.874444] Initializing cgroup subsys ns
[ 11.874449] Initializing cgroup subsys cpuacct
[ 11.874459] CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000
00000000 00000001 00000000 00000001 00000000
[ 11.874468] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
[ 11.874471] CPU: L2 Cache: 1024K (64 bytes/line)
[ 11.874474] CPU: After all inits, caps: 078bfbff e3d3fbff 00000000
00000410 00000001 00000000 00000001 00000000
[ 11.874484] Compat vDSO mapped to ffffe000.
[ 11.874495] Checking 'hlt' instruction... OK.
[ 11.890560] SMP alternatives: switching to UP code
[ 11.891799] Freeing SMP alternatives: 11k freed
[ 11.891919] Early unpacking initramfs... done
[ 12.270793] ACPI: Core revision 20070126
[ 12.270858] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml
not found.
[ 12.275131] CPU0: AMD Turion(tm) 64 Mobile Technology ML-30 stepping 02
[ 12.275151] Total of 1 processors activated (3202.13 BogoMIPS).
[ 12.275306] ENABLING IO-APIC IRQs
[ 12.275493] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 12.421523] Brought up 1 CPUs
[ 12.421562] CPU0 attaching sched-domain:
[ 12.421565] domain 0: span 01
[ 12.421567] groups: 01
[ 12.421740] net_namespace: 64 bytes
[ 12.421747] Booting paravirtualized kernel on bare hardware
[ 12.422232] Time: 4:49:24 Date: 10/06/08
[ 12.422257] NET: Registered protocol family 16
[ 12.422441] EISA bus registered
[ 12.422462] ACPI: bus type pci registered
[ 12.422606] PCI: PCI BIOS revision 2.10 entry at 0xfd776, last bus=1
[ 12.422609] PCI: Using configuration type 1
[ 12.422616] Setting up standard PCI resources
[ 12.424620] ACPI: EC: Look up EC in DSDT
[ 12.425962] ACPI: Interpreter enabled
[ 12.425965] ACPI: (supports S0 S3 S4 S5)
[ 12.425976] ACPI: Using IOAPIC for interrupt routing
[ 12.426247] ACPI: EC: non-query interrupt received, switching to
interrupt mode
[ 12.441760] ACPI: EC: GPE = 0x19, I/O: command/status = 0x66, data = 0x62
[ 12.441763] ACPI: EC: driver started in interrupt mode
[ 12.441801] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 12.441930] Enabling SiS 96x SMBus.
[ 12.442415] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 12.448361] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 *7 9 10 11)
[ 12.448439] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *4 5 7 9 10 11)
[ 12.448514] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 9 10 11)
[ 12.448588] ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 7 9 10 11)
[ 12.448676] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 *9 10 11)
[ 12.448751] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 *11)
[ 12.448822] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11) *0,
disabled.
[ 12.448894] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 *10 11)
[ 12.449001] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 12.449029] pnp: PnP ACPI init
[ 12.449035] ACPI: bus type pnp registered
[ 12.450446] pnp: PnP ACPI: found 8 devices
[ 12.450449] ACPI: ACPI bus type pnp unregistered
[ 12.450452] PnPBIOS: Disabled by ACPI PNP
[ 12.450654] PCI: Using ACPI for IRQ routing
[ 12.450657] PCI: Routing PCI interrupts for all devices because
"pci=routeirq" specified
[ 12.450665] ACPI: PCI Interrupt 0000:00:02.1[B] -> GSI 17 (level, low) ->
IRQ 16
[ 12.450671] ACPI: PCI Interrupt 0000:00:02.5[A] -> GSI 16 (level, low) ->
IRQ 17
[ 12.450677] ACPI: PCI Interrupt 0000:00:02.6[C] -> GSI 18 (level, low) ->
IRQ 18
[ 12.450680] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) ->
IRQ 18
[ 12.450685] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) ->
IRQ 19
[ 12.450691] ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) ->
IRQ 20
[ 12.450697] ACPI: PCI Interrupt 0000:00:03.2[D] -> GSI 23 (level, low) ->
IRQ 21
[ 12.450702] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) ->
IRQ 22
[ 12.450705] ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 19 (level, low) ->
IRQ 22
[ 12.450709] ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 17 (level, low) ->
IRQ 16
[ 12.450712] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) ->
IRQ 17
[ 12.453473] NET: Registered protocol family 8
[ 12.453476] NET: Registered protocol family 20
[ 12.453537] AppArmor: AppArmor Filesystem Enabled
[ 12.457422] Time: tsc clocksource has been installed.
[ 12.465444] system 00:04: ioport range 0x8000-0x807f has been reserved
[ 12.465447] system 00:04: ioport range 0x8080-0x80ff has been reserved
[ 12.465451] system 00:04: ioport range 0x8100-0x811f has been reserved
[ 12.465454] system 00:04: ioport range 0x4d0-0x4d1 has been reserved
[ 12.465457] system 00:04: ioport range 0x3f0-0x3f1 has been reserved
[ 12.465460] system 00:04: iomem range 0xfec00000-0xfecfffff has been
reserved
[ 12.465464] system 00:04: iomem range 0xfed00000-0xfed003ff has been
reserved
[ 12.465467] system 00:04: iomem range 0xfee00000-0xfeefffff has been
reserved
[ 12.465470] system 00:04: iomem range 0xffc00000-0xffc00fff has been
reserved
[ 12.465474] system 00:04: iomem range 0xffe00000-0xffe00fff has been
reserved
[ 12.465477] system 00:04: iomem range 0xffe80000-0xffefffff has been
reserved
[ 12.465480] system 00:04: iomem range 0xfffe0000-0xfffeffff could not be
reserved
[ 12.465484] system 00:04: iomem range 0xffff0000-0xffffffff could not be
reserved
[ 12.465487] system 00:04: iomem range 0x0-0x0 could not be reserved
[ 12.495823] PCI: Bridge: 0000:00:01.0
[ 12.495827] IO window: a000-afff
[ 12.495831] MEM window: e2100000-e21fffff
[ 12.495834] PREFETCH window: e8000000-efffffff
[ 12.495839] PCI: Bus 2, cardbus bridge: 0000:00:06.0
[ 12.495841] IO window: 00002400-000024ff
[ 12.495844] IO window: 00002800-000028ff
[ 12.495848] PREFETCH window: 30000000-33ffffff
[ 12.495851] MEM window: 34000000-37ffffff
[ 12.495867] PCI: Enabling device 0000:00:06.0 (0000 -> 0003)
[ 12.495870] ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 19 (level, low) ->
IRQ 22
[ 12.495883] NET: Registered protocol family 2
[ 12.533385] IP route cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 12.533620] TCP established hash table entries: 16384 (order: 5, 131072
bytes)
[ 12.533737] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 12.533866] TCP: Hash tables configured (established 16384 bind 16384)
[ 12.533869] TCP reno registered
[ 12.545416] checking if image is initramfs... it is
[ 12.996634] Switched to high resolution mode on CPU 0
[ 13.280833] Freeing initrd memory: 7327k freed
[ 13.281017] Simple Boot Flag at 0x38 set to 0x1
[ 13.281517] audit: initializing netlink socket (disabled)
[ 13.281532] audit(1223268564.384:1): initialized
[ 13.283502] VFS: Disk quotas dquot_6.5.1
[ 13.283576] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 13.283715] io scheduler noop registered
[ 13.283718] io scheduler anticipatory registered
[ 13.283720] io scheduler deadline registered
[ 13.283730] io scheduler cfq registered (default)
[ 13.701749] Boot video device is 0000:01:00.0
[ 13.701986] isapnp: Scanning for PnP cards...
[ 14.054950] isapnp: No Plug & Play device found
[ 14.083925] Real Time Clock Driver v1.12ac
[ 14.084021] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ
sharing enabled
[ 14.084521] ACPI: PCI Interrupt 0000:00:02.6[C] -> GSI 18 (level, low) ->
IRQ 18
[ 14.084528] ACPI: PCI interrupt for device 0000:00:02.6 disabled
[ 14.085147] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024
blocksize
[ 14.085216] input: Macintosh mouse button emulation as
/devices/virtual/input/input0
[ 14.085303] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64
irq 1,12
[ 14.087304] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 14.087309] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 14.094941] mice: PS/2 mouse device common for all mice
[ 14.095052] EISA: Probing bus 0 at eisa.0
[ 14.095058] Cannot allocate resource for EISA slot 1
[ 14.095061] Cannot allocate resource for EISA slot 2
[ 14.095081] Cannot allocate resource for EISA slot 8
[ 14.095083] EISA: Detected 0 cards.
[ 14.095086] cpuidle: using governor ladder
[ 14.095088] cpuidle: using governor menu
[ 14.095188] NET: Registered protocol family 1
[ 14.095213] Using IPI No-Shortcut mode
[ 14.095249] registered taskstats version 1
[ 14.095343] Magic number: 12:682:817
[ 14.095509] hash matches device ptype
[ 14.095562] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 14.095564] EDD information not available.
[ 14.096116] Freeing unused kernel memory: 368k freed
[ 14.134789] input: AT Translated Set 2 keyboard as
/devices/platform/i8042/serio0/input/input1
[ 15.314568] fuse init (API version 7.9)
[ 15.335289] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 15.335296] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 15.338881] ACPI: Thermal Zone [THRM] (32 C)
[ 15.956155] SCSI subsystem initialized
[ 16.022196] libata version 3.00 loaded.
[ 16.041515] usbcore: registered new interface driver usbfs
[ 16.041540] usbcore: registered new interface driver hub
[ 16.058866] usbcore: registered new device driver usb
[ 16.075750] sis900.c: v1.08.10 Apr. 2 2006
[ 16.075809] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) ->
IRQ 22
[ 16.080698] 0000:00:04.0: Realtek RTL8201 PHY transceiver found at
address 13.
[ 16.086585] 0000:00:04.0: Using transceiver found at address 13 as
default
[ 16.089131] eth0: SiS 900 PCI Fast Ethernet at 0x1800, IRQ 22,
00:c0:9f:87:b2:21
[ 16.094009] pata_sis 0000:00:02.5: version 0.5.2
[ 16.094034] ACPI: PCI Interrupt 0000:00:02.5[A] -> GSI 16 (level, low) ->
IRQ 17
[ 16.102068] scsi0 : pata_sis
[ 16.115756] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller
(OHCI) Driver
[ 16.127670] scsi1 : pata_sis
[ 16.127853] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x2000 irq
14
[ 16.127856] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x2008 irq
15
[ 16.291787] ata1.00: ATA-6: IC25N060ATMR04-0, MO3OAD4A, max UDMA/100
[ 16.291793] ata1.00: 117210240 sectors, multi 16: LBA48
[ 16.307838] ata1.00: configured for UDMA/100
[ 16.643296] ata2.00: ATAPI: PIONEER DVD-RW DVR-K15RA, 1.04, max UDMA/33
[ 16.831191] ata2.00: configured for UDMA/33
[ 16.831313] scsi 0:0:0:0: Direct-Access ATA IC25N060ATMR04-0
MO3O PQ: 0 ANSI: 5
[ 16.839486] scsi 1:0:0:0: CD-ROM PIONEER DVD-RW DVR-K15RA
1.04 PQ: 0 ANSI: 5
[ 16.842498] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) ->
IRQ 19
[ 16.842520] ohci_hcd 0000:00:03.0: OHCI Host Controller
[ 16.842792] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus
number 1
[ 16.842810] ohci_hcd 0000:00:03.0: irq 19, io mem 0xe2002000
[ 16.898562] usb usb1: configuration #1 chosen from 1 choice
[ 16.898586] hub 1-0:1.0: USB hub found
[ 16.898594] hub 1-0:1.0: 3 ports detected
[ 17.002339] ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) ->
IRQ 20
[ 17.002350] ohci_hcd 0000:00:03.1: OHCI Host Controller
[ 17.002370] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus
number 2
[ 17.002385] ohci_hcd 0000:00:03.1: irq 20, io mem 0xe2003000
[ 17.058282] usb usb2: configuration #1 chosen from 1 choice
[ 17.058307] hub 2-0:1.0: USB hub found
[ 17.058313] hub 2-0:1.0: 3 ports detected
[ 17.162300] ACPI: PCI Interrupt 0000:00:03.2[D] -> GSI 23 (level, low) ->
IRQ 21
[ 17.162308] ehci_hcd 0000:00:03.2: EHCI Host Controller
[ 17.162332] ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus
number 3
[ 17.162363] PCI: cache line size of 64 is not supported by device
0000:00:03.2
[ 17.162372] ehci_hcd 0000:00:03.2: irq 21, io mem 0xe2004000
[ 17.174017] ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00, driver 10
Dec 2004
[ 17.174148] usb usb3: configuration #1 chosen from 1 choice
[ 17.174172] hub 3-0:1.0: USB hub found
[ 17.174179] hub 3-0:1.0: 6 ports detected
[ 17.278142] ACPI: PCI Interrupt 0000:00:0b.0[A] -> GSI 17 (level, low) ->
IRQ 16
[ 17.297828] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor
0x4243)
[ 17.297836] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor
0x4243)
[ 17.297842] ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
[ 17.297847] ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
[ 17.337782] ssb: Sonics Silicon Backplane found on PCI device
0000:00:0b.0
[ 17.361483] Driver 'sd' needs updating - please use bus_type methods
[ 17.361574] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012
MB)
[ 17.361589] sd 0:0:0:0: [sda] Write Protect is off
[ 17.361591] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 17.361608] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 17.361662] sd 0:0:0:0: [sda] 117210240 512-byte hardware sectors (60012
MB)
[ 17.361672] sd 0:0:0:0: [sda] Write Protect is off
[ 17.361674] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 17.361688] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 17.361705] sda:<4>Driver 'sr' needs updating - please use bus_type
methods
[ 17.391457] sda1 sda2 sda3 sda4
[ 17.401582] sd 0:0:0:0: [sda] Attached SCSI disk
[ 17.407243] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 17.407263] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 17.431298] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 17.431304] Uniform CD-ROM driver Revision: 3.20
[ 17.431357] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 17.692321] Attempting manual resume
[ 17.692326] swsusp: Resume From Partition 8:3
[ 17.692328] PM: Checking swsusp image.
[ 17.692466] PM: Resume from disk failed.
[ 17.732370] kjournald starting. Commit interval 5 seconds
[ 17.732383] EXT3-fs: mounted filesystem with ordered data mode.
[ 17.809004] usb 2-2: new low speed USB device using ohci_hcd and address
2
[ 18.030653] usb 2-2: configuration #1 chosen from 1 choice
[ 31.437600] Linux agpgart interface v0.102
[ 31.647320] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 31.827013] Yenta: CardBus bridge found at 0000:00:06.0 [1025:0083]
[ 31.827031] Yenta: Using CSCINT to route CSC interrupts to PCI
[ 31.827033] Yenta: Routing CardBus interrupts to PCI
[ 31.827038] Yenta TI: socket 0000:00:06.0, mfunc 0x00521d22, devctl 0x64
[ 31.890870] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 32.059315] Yenta: ISA IRQ mask 0x06f8, PCI irq 22
[ 32.059319] Socket status: 30000006
[ 32.122727] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 32.122745] agpgart: Detected AGP bridge 0
[ 32.124446] agpgart: AGP aperture is 32M @ 0xe0000000
[ 32.124488] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x8100
[ 32.246377] input: Power Button (FF) as /devices/virtual/input/input3
[ 32.262250] ACPI: Power Button (FF) [PWRF]
[ 32.262353] input: Lid Switch as /devices/virtual/input/input4
[ 32.263183] ACPI: Lid Switch [LID]
[ 32.263260] input: Power Button (CM) as /devices/virtual/input/input5
[ 32.282503] ACPI: Power Button (CM) [PWRB]
[ 32.282581] input: Sleep Button (CM) as /devices/virtual/input/input6
[ 32.294185] ACPI: Sleep Button (CM) [SLPB]
[ 32.295103] ACPI: AC Adapter [ACAD] (on-line)
[ 32.332253] ACPI: Battery Slot [BAT1] (battery present)
[ 32.583880] ACPI: WMI-Acer: Mapper loaded
[ 32.734563] acer_acpi: Acer Laptop ACPI Extras version 0.11.1
[ 32.734578] acer_acpi: No or unsupported WMI interface, unable to load.
[ 32.965123] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x126eb1, caps:
0xa04713/0x4000
[ 32.999370] input: SynPS/2 Synaptics TouchPad as
/devices/platform/i8042/serio1/input/input7
[ 33.283688] b43-phy0: Broadcom 4318 WLAN found
[ 33.324561] b43-phy0 debug: Found PHY: Analog 3, Type 2, Revision 7
[ 33.324584] b43-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050,
Revision 8
[ 33.392830] phy0: Selected rate control algorithm 'simple'
[ 33.913751] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) ->
IRQ 18
[ 34.293943] usbcore: registered new interface driver hiddev
[ 34.314181] input: Microsoft Microsoft USB Wireless Mouse as
/devices/pci0000:00/0000:00:03.1/usb2/2-2/2-2:1.0/input/input8
[ 34.331294] input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft USB
Wireless Mouse] on usb-0000:00:03.1-2
[ 34.331314] usbcore: registered new interface driver usbhid
[ 34.331319] /build/buildd/linux-2.6.24/drivers/hid/usbhid/hid-core.c:
v2.6:USB HID core driver
[ 34.738364] intel8x0_measure_ac97_clock: measured 55461 usecs
[ 34.738369] intel8x0: clocking to 48000
[ 35.478868] cs: IO port probe 0x100-0x3af: clean.
[ 35.480502] cs: IO port probe 0x3e0-0x4ff: excluding 0x480-0x48f
[ 35.481195] cs: IO port probe 0x820-0x8ff: clean.
[ 35.481771] cs: IO port probe 0xc00-0xcf7: clean.
[ 35.482511] cs: IO port probe 0xa00-0xaff: clean.
[ 36.838974] lp: driver loaded but no devices found
[ 36.891041] usbcore: registered new interface driver usbserial
[ 36.891059] /build/buildd/linux-2.6.24/drivers/usb/serial/usb-serial.c:
USB Serial support registered for generic
[ 36.891074] usbcore: registered new interface driver usbserial_generic
[ 36.891077] /build/buildd/linux-2.6.24/drivers/usb/serial/usb-serial.c:
USB Serial Driver core
[ 36.906974] /build/buildd/linux-2.6.24/drivers/usb/serial/usb-serial.c:
USB Serial support registered for Handspring Visor / Palm OS
[ 36.906991] /build/buildd/linux-2.6.24/drivers/usb/serial/usb-serial.c:
USB Serial support registered for Sony Clie 3.5
[ 36.907006] /build/buildd/linux-2.6.24/drivers/usb/serial/usb-serial.c:
USB Serial support registered for Sony Clie 5.0
[ 36.907027] usbcore: registered new interface driver visor
[ 36.907030] /build/buildd/linux-2.6.24/drivers/usb/serial/visor.c: USB
HandSpring Visor / Palm OS driver
[ 37.056755] Adding 2000084k swap on /dev/sda3. Priority:-1 extents:1
across:2000084k
[ 37.595717] EXT3 FS on sda2, internal journal
[ 38.380325] kjournald starting. Commit interval 5 seconds
[ 38.380567] EXT3 FS on sda4, internal journal
[ 38.380572] EXT3-fs: mounted filesystem with ordered data mode.
[ 39.056286] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 39.601889] No dock devices found.
[ 39.942769] powernow-k8: Found 1 AMD Turion(tm) 64 Mobile Technology
ML-30 processors (1 cpu cores) (version 2.20.00)
[ 39.942809] powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x4
[ 39.942812] powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x16
[ 41.018877] apm: BIOS not found.
[ 41.151337] ppdev: user-space parallel port driver
[ 41.396060] audit(1223268593.729:2): type=1503
operation="inode_permission" requested_mask="a::" denied_mask="a::"
name="/dev/tty" pid=4788 profile="/usr/sbin/cupsd" namespace="default"
[ 41.933847] NET: Registered protocol family 10
[ 41.934111] lo: Disabled Privacy Extensions
[ 42.871063] input: b43-phy0 as /devices/virtual/input/input9
[ 43.149132] Bluetooth: Core ver 2.11
[ 43.152024] NET: Registered protocol family 31
[ 43.152029] Bluetooth: HCI device and connection manager initialized
[ 43.152035] Bluetooth: HCI socket layer initialized
[ 43.219694] b43-phy0 debug: Loading firmware version 351.126 (2006-07-29
05:54:02)
[ 43.284004] Bluetooth: L2CAP ver 2.9
[ 43.284010] Bluetooth: L2CAP socket layer initialized
[ 43.297657] Bluetooth: RFCOMM socket layer initialized
[ 43.297866] Bluetooth: RFCOMM TTY layer initialized
[ 43.297869] Bluetooth: RFCOMM ver 1.8
[ 44.768282] b43-phy0 debug: Chip initialized
[ 44.768817] b43-phy0 debug: 32-bit DMA initialized
[ 44.790090] Registered led device: b43-phy0:tx
[ 44.790346] Registered led device: b43-phy0:rx
[ 44.790521] Registered led device: b43-phy0:radio
[ 44.790553] b43-phy0 debug: Wireless interface started
[ 44.846534] b43-phy0 debug: Adding Interface type 2
[ 44.846977] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 45.741376] APIC error on CPU0: 00(40)
[ 46.868320] eth0: Media Link On 100mbps full-duplex
[ 47.162976] NET: Registered protocol family 17
[ 97.479178] Marking TSC unstable due to: cpufreq changes.
[ 97.507071] Time: acpi_pm clocksource has been installed.
[ 97.728081] Clocksource tsc unstable (delta = -124637536 ns)
[ 112.284223] eth0: no IPv6 routers present
[ 959.980131] APIC error on CPU0: 40(40)
Module Size Used by
af_packet 23812 2
rfcomm 41744 2
l2cap 25728 13 rfcomm
bluetooth 61156 4 rfcomm,l2cap
rfkill_input 5504 0
ipv6 267780 14
ppdev 10372 0
powernow_k8 16704 0
cpufreq_powersave 2688 0
cpufreq_ondemand 9740 1
cpufreq_userspace 5284 0
cpufreq_conservative 8712 0
cpufreq_stats 7104 0
freq_table 5536 3 powernow_k8,cpufreq_ondemand,cpufreq_stats
video 19856 0
output 4736 1 video
dock 11280 0
sbs 15112 0
sbshc 7680 1 sbs
container 5632 0
iptable_filter 3840 0
ip_tables 14820 1 iptable_filter
x_tables 16132 1 ip_tables
visor 18572 0
usbserial 35816 1 visor
parport_pc 36260 0
lp 12324 0
parport 37832 3 ppdev,parport_pc,lp
joydev 13120 0
pcmcia 40876 0
usbhid 31872 0
hid 38784 1 usbhid
arc4 2944 2
ecb 4480 2
blkcipher 8324 1 ecb
snd_intel8x0 35356 3
snd_ac97_codec 101028 1 snd_intel8x0
ac97_bus 3072 1 snd_ac97_codec
snd_pcm_oss 42144 0
snd_mixer_oss 17920 1 snd_pcm_oss
snd_pcm 78596 3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
b43 144420 0
rfkill 8592 3 rfkill_input,b43
mac80211 165652 1 b43
snd_seq_dummy 4868 0
cfg80211 15112 1 mac80211
evdev 13056 7
wmi_acer 9644 0
led_class 6020 1 b43
snd_seq_oss 35584 0
snd_seq_midi 9376 0
serio_raw 7940 0
input_polldev 5896 1 b43
snd_rawmidi 25760 1 snd_seq_midi
psmouse 40336 0
snd_seq_midi_event 8320 2 snd_seq_oss,snd_seq_midi
sis_agp 10116 0
battery 14212 0
ac 6916 0
button 9232 0
snd_seq 54224 6
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 24836 2 snd_pcm,snd_seq
snd_seq_device 9612 5
snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq
snd 56996 17
snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_dummy,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
i2c_sis96x 6148 0
amd64_agp 13444 1
shpchp 34452 0
pci_hotplug 30880 1 shpchp
yenta_socket 27276 1
rsrc_nonstatic 13696 1 yenta_socket
pcmcia_core 40596 3 pcmcia,yenta_socket,rsrc_nonstatic
pcspkr 4224 0
k8temp 6656 0
soundcore 8800 1 snd
i2c_core 24832 1 i2c_sis96x
agpgart 34760 2 sis_agp,amd64_agp
snd_page_alloc 11400 2 snd_intel8x0,snd_pcm
ext3 136712 2
jbd 48404 1 ext3
mbcache 9600 1 ext3
sg 36880 0
sr_mod 17956 0
cdrom 37408 1 sr_mod
sd_mod 30720 4
pata_acpi 8320 0
ata_generic 8324 0
ssb 34308 1 b43
ehci_hcd 37900 0
ohci_hcd 25348 0
pata_sis 15236 3
sis900 24320 0
mii 6400 1 sis900
usbcore 146028 6 visor,usbserial,usbhid,ehci_hcd,ohci_hcd
libata 159344 3 pata_acpi,ata_generic,pata_sis
scsi_mod 151436 4 sg,sr_mod,sd_mod,libata
thermal 16796 0
processor 36872 3 powernow_k8,thermal
fan 5636 0
fbcon 42912 0
tileblit 3456 1 fbcon
font 9472 1 fbcon
bitblit 6784 1 fbcon
softcursor 3072 1 bitblit
fuse 50708 3
