Marv,
Something is fishy here. Now it starts looking like the 11c11040 part
of scanModem was true.
I ran scanModem with the pci id's of the modem and I got the following:
Predictive diagnostics for card in bus fake:
Modem chipset detected on
NAME="FakeName"
CLASS=FakeClass
PCIDEV=8086:284b
SUBSYS=1043:1339
IRQ=fake
HDA=8086:284b
SOFT=8086:284b.HDA
ArchivedChip=0x11c11040
IDENT=11c11040
Driver=agrmodem+agrserial
DRIVER=agrmodem+agrserial
For candidate modem in: fake
FakeClass FakeName
Primary device ID: 8086:284b
Subsystem PCI_id 1043:1339
Softmodem codec or chipset from diagnostics:
from Archives: 0x11c11040
I am not 100% sure here, but I had the same thing happen one time when
I tried the SLMODEMD code with this type of modem(11c11040),
everything seemed correct all was fine. The bad part the looping of
No Carrier, like in your message.
It is very strange that SLMODEMD.gcc4.tar.gz was serving and then you
updated the kernel and now it does not work. Why can't you change the
default behavior to have at least two working kernels so that you have
something to fall back on. *This should not be the case with
SLMODEMD, but this appears to be a special case*
Regards,
Antonio
On Wed, Aug 6, 2008 at 10:38 PM, Eric <dragon.wind@xxxxxxxxxxxx> wrote:
> after installing Marvin new slmodemd and
> carring out Antonio instructions
>
> Eric,
>
> You might want to change
> Init string here
>
> Put a "#" in front of the following one
>> Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
>
> And remove it from here.
>> # Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +MS=90
>
> Test out conection. Does it get to connect?
>
> It seems strange that after a kernel upgrade that SLMODEMD does not work
> any more since it is kernel independent.
>
> Regards,
>
>
> Antonio
>
> I still get
>
> [sudo] password for eric:
> --> WvDial: Internet dialer version 1.60
> --> Cannot get information for serial port.
> --> Initializing modem.
> --> Sending: ATZ
> ATZ
> OK
> --> Sending: ATQ0 V1 E1 S0=0 X3 &C1 &D2 +MS=90
> ATQ0 V1 E1 S0=0 X3 &C1 &D2 +MS=90
> OK
> --> Modem initialized.
> --> Please enter password (or empty password to stop):
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> ATDT0198333966
> NO CARRIER
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> ATDT0198333966
> --> Timed out while dialing. Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> --> Sending: ATDT0198333966
> --> Waiting for carrier.
> NO CARRIER
> ATDT0198333966
> --> No Carrier! Trying again.
> Caught signal 2: Attempting to exit gracefully...
> --> Disconnecting at Thu Aug 7 13:21:14 2008
>
> On Wed, 2008-08-06 at 20:48 -0400, Marvin Stodolsky wrote:
>> Try replacing your slmodemd with the attached
>>
>>
>
>
>
>
