Jens ADSL modems use entirely different software than older dialout modems. There is an ADSL Howto: http://www.rhapsodyk.net/adsl/HOWTO/ MarvS On Mon, Jul 28, 2008 at 1:16 AM, Jens KRIEBITZSCH <jens.kriebitzsch@xxxxxxxx> wrote: > Dear all, > > I just installed Ubuntu on a dual boot engine, and I have no internet access so far via Ubuntu, but it works still OK under Windows. ScanModem seems to detect a Connexant Access Runner (which I use), device number 0572:cb00. But it doesn't look happy with the rest. Windows uses a file CnxEtU.sys. How to proceed further from here? > > Please find attached ModemData.txt > > Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List Server, > as HTML can contain viruses. Use as the email Subject Line: > YourName, YourCountry kernel 2.6.24-19-generic > With this Subject Line cogent experts will be alerted, and useful case names left in the Archive. > YourCountry will enable Country specific guidance. Linux experts in YourCountry > can be found through: http://www.linux.org/groups/index.html. > They will know your Country's modem code, which may be essential for dialup service. > Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an Internet Provider mail filters. > So in a day, also check the Archived responses at http://www.linmodems.org > -------------------------- System information ---------------------------- > CPU=i686, > Linux version 2.6.24-19-generic (buildd@palmer) (gcc version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Wed Jun 18 14:43:41 UTC 2008 > scanModem update of: 2008_07_25 > > There are no blacklisted modem drivers in /etc/modprobe* files > Attached USB devices are: > ID 0aec:3260 Neodio Technologies Corp. 7-in-1 Card Reader > ID 046d:08c9 Logitech, Inc. > ID 1267:0212 Logic3 / SpectraVideo plc > ID 0572:cb00 Conexant Systems (Rockwell), Inc. E-Tech ADSL Modem v2 > > USB modems not recognized > > For candidate card in slot 00:1b.0, firmware information and bootup diagnostics are: > PCI slot PCI ID SubsystemID Name > ---------- --------- --------- -------------- > 00:1b.0 8086:2668 1043:813d Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW > > Modem interrupt assignment and sharing: > 16: 107849 0 IO-APIC-fasteoi uhci_hcd:usb4, HDA Intel, radeon@pci:0000:04:00.0 > --- Bootup diagnostics for card in PCI slot 00:1b.0 ---- > [ 61.969338] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16 > [ 61.969368] PCI: Setting latency timer of device 0000:00:1b.0 to 64 > > > ===== Advanced Linux Sound Architecture (ALSA) diagnostics ===== > The ALSA packages provide audio support and also drivers for some modems. > ALSA diagnostics are written during bootup to /proc/asound/ folders. > > PCI slot 00:1b.0 has a High Definition Audio Card > The drivers are in the kernel modules tree at: > /lib/modules/2.6.24-19-generic/ubuntu/sound/alsa-driver/pci/hda/snd-hda-intel.ko > > The ALSA verion is 1.0.16. > The modem cards detected by "aplay -l" are: None > > > The /proc/asound/pcm file reports: > ----------------------- > 00-01: CMI9880 Digital : CMI9880 Digital : playback 1 : capture 1 > 00-00: CMI9880 : CMI9880 : playback 1 : capture 2 > 02-00: USB Audio : USB Audio : capture 1 > > about /proc/asound/cards: > ------------------------ > 0 [Intel ]: HDA-Intel - HDA Intel > HDA Intel at 0xcfcf4000 irq 16 > 1 [UART ]: MPU-401 UART - MPU-401 UART > MPU-401 UART at 0x300, irq 5 > 2 [U0x46d0x8c9 ]: USB-Audio - USB Device 0x46d:0x8c9 > USB Device 0x46d:0x8c9 at usb-0000:00:1d.7-3, high speed > === Finished firmware and bootup diagnostics, next deducing cogent software. === > > A candidate modem is not evident among the PCI devices: > ------------------------------------------------ > 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) > 00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) > 00:1f.2 IDE interface: Intel Corporation 82801FR/FRW (ICH6R/ICH6RW) SATA Controller (rev 03) > 00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03) > 01:03.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) > 01:04.0 Mass storage controller: Integrated Technology Express, Inc. IT/ITE8212 Dual channel ATA RAID controller (rev 13) > 01:05.0 Mass storage controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) > 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 15) > 04:00.0 VGA compatible controller: ATI Technologies Inc RV380 0x3e50 [Radeon X600] > 04:00.1 Display controller: ATI Technologies Inc RV380 [Radeon X600] (Secondary) > ------------------------------------------------ > with USB and bridge devices not displayed. > > If your modem is connected by an external serial cable, > or mounted internally on an ISA card, scanModem would not access it. > Try with Root permission > $ sudo wvdialconf /etc/wvdial.conf > to detect these modem types and some USB modems. > If the detection is successful, read the DOCs/wvdial.txt . > Edit the /etc/wvdial.conf with Root permission: > sudo gedit /etc/wvdial.conf > will be able to dial out with Root permission: > sudo wvdial > > Many modems for which scanModem fails have Conexant chips. > From http://www.linuxant.com/drivers/modemident.php > get the ListModem tool, which will report on Conexant chipset modems > > If the above tests fail, please provide any independent information available on your modem. > If an alternative boot into Microsoft windows can be done, do mouse > clicks on: > Start > Settings > Control Panel > Classical View (for Window XP) > System >> Hardware > Device Manager > Modems > Click on the + > Modem. Double click to > expand the graphic. Manufacturer information may be displayed. For example, CXT > stands for Conexant. Click the Diagnostics Tab. Record any hardware ID or vendor > and device information. From the Driver Details TAB, copy out the VENdor and DEVice information. > Next do the Query Modem and record the ATI specifications displayed such as: > ATI3 - Agere SoftModem Version 2.1.22 > ATI5 - 2.1.22, AMR Intel MB, AC97 ID:SIL REV:0x27 > Try to identify the modem setup file, with name perhaps MODEM.INF. > If may contain chipset Vendor informaton. > > The /proc/asound/ audio+modem diagostics are being copied. > Finished copy to Modem/ALSAroot.tgz > > Predictive diagnostics for card in bus 00:1b.0: > Modem chipset not detected on > NAME="Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW " > CLASS=0403 > PCIDEV=8086:2668 > SUBSYS=1043:813d > IRQ=16 > HDA=8086:2668 > SOFT=8086:2668.HDA > > > High Definition Audio (HDA) cards MAY host a modem chip in their Subsystem, > and many are supported by the ALSA audio+modem driver snd-hda-intel > A modem was not detected on HDA card 8086:2668. > If another modem card is present, then most likely 8086:2668 does not host a modem. > If another modem card has not been detected, then possibilities are: > 1) A Conexant modem chip is present on 8086:2668, as Conexant chips > are frequently not detectable by ALSA diagnostics > 2) The modem may be of the older non-PCI Controller Chipset (hardware) type. > Try detection with Root permission: > sudo wvdialconf /etc/wvdial.conf > > For candidate modem in: 00:1b.0 > 0403 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW > Primary device ID: 8086:2668 > Subsystem PCI_id 1043:813d > Softmodem codec or chipset from diagnostics: > from Archives: > > > > Support type needed or chipset: > > Support can likely be achieved through two mutually exclusive alternatives: > 1) The hsfmodem software for Conexant chipset modems: Read DOCs/Conexant.txt > The following ALSA alternative CANNOT work with Conexant modems. > > 2) An ALSA modem driver plus slmodemd. Read DOCs/Smartlink.txt for details, and > to test get the package SLMODEMD.gcc4.2.tar.gz from: > http://linmodems.technion.ac.il/packages/smartlink/ > > ----------------end Softmodem section -------------- > > Writing DOCs/Intel.txt > > For owners of a Dell PCs with Conexant HSF modems, a driver source package with full speed enabled is available, but requires driver compiling. Read DOCs/Conexant.txt > > From http://www.linuxant.com/drivers/hsf/full/downloads-ubuntu-x86.php > download hsfmodem-7.68.00.12full_k2.6.24_19_generic_ubuntu_i386.deb.zip > Under Linux unpack with: > $ unzip hsfmodem*.zip > Then install with: > $ sudo dpkg -i hsfmodem*.deb > Subsequently, the modem should be found with > $ sudo wvdialconf /etc/wvdial.conf > Edit in your personal information with: > $ sudo gedit /etc/wvdial.conf > and try dialing out with: > $ sudo wvdial. > See DOCs/Testing.txt for details. > > Read DOCs/Conexant.txt > > Writing DOCs/Conexant.txt > > Writing DOCs/Smartlink.txt > ============ end Smartlink section ===================== > > > The base of the UDEV device file system is: /dev/.udev > > Versions adequately match for the compiler installed: 4.2.3 > and the compiler used in kernel assembly: 4.2.3 > > > > Minimal compiling resources appear complete: > make utility - /usr/bin/make > Compiler version 4.2 > linuc_headers base folder /lib/modules/2.6.24-19-generic/build > > However some compilations and executable functions may need additional files, > in the FileNames.h (so called kernel "h"eaders) collection installed in /usr/include/ . > For martian_modem, additional required packages are n. The also required headers of package libc6 are commonly installed by default. > Compiling hsfmodem drivers does require linux-libc-dev and libc6-dev packages, for kernels 2.6.24 and later versions. > In not included on your install CD, search for them at http://packages.ubuntu.com > or comparable Repository for other Linux distros. > When compiling ALSA drivers, the utility "patch" will also be needed. > > > > > If a driver compilation fails, with message including some lack of some FileName.h (stdio.h for example), then > Some additional kernel-header files need installation to /usr/include. The minimal additional packages are libc6-dev > and any of its dependents, under Ubuntu linux-libc-dev > > If an alternate ethernet connection is available, > $ apt-get update > $ apt-get -s install linux-kernel-devel > will install needed packages. > For Debian/Ubuntu related distributions, run the following command to display the needed package list: > > Otherwise packages have to be found through http://packages.ubuntu.com > Once downloaded and transferred into a Linux partition, > they can be installed alltogether with: > $ sudo dpkg -i *.deb > > > Checking pppd properties: > -rwsr-xr-- 1 root dip 269256 2007-10-05 03:57 /usr/sbin/pppd > > In case of an "error 17" "serial loopback" problem, see: > http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html > > To enable dialout without Root permission do: > $ su - root (not for Ubuntu) > sudo chmod a+x /usr/sbin/pppd > or under Ubuntu related Linuxes > sudo chmod a+x /usr/sbin/pppd > > Checking settings of: /etc/ppp/options > asyncmap 0 > noauth > crtscts > lock > hide-password > modem > proxyarp > lcp-echo-interval 30 > lcp-echo-failure 4 > noipx > > In case of a message like: > Warning: Could not modify /etc/ppp/pap-secrets: Permission denied > see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html > > Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0 > Which can interfere with Browser naviagation. > > Don't worry about the following, it is for experts should trouble shooting be necessary. > ========================================================== > > Checking for modem support lines: > -------------------------------------- > /device/modem symbolic link: > slmodemd created symbolic link /dev/ttySL0: > Within /etc/udev/ files: > > Within /etc/modprobe.conf files: > /etc/modprobe.d/blacklist-modem:# Uncomment these entries in order to blacklist unwanted modem drivers > /etc/modprobe.d/blacklist-modem:# blacklist snd-atiixp-modem > /etc/modprobe.d/blacklist-modem:# blacklist snd-via82xx-modem > /etc/modprobe.d/alsa-base:options snd-atiixp-modem index=-2 > /etc/modprobe.d/alsa-base:options snd-via82xx-modem index=-2 > Within any ancient /etc/devfs files: > > Within ancient kernel 2.4.n /etc/module.conf files: > > --------- end modem support lines -------- > > > __________________________________________________________ > Gesendet von Yahoo! Mail. > Dem pfiffigeren Posteingang. > http://de.overview.mail.yahoo.com
