Okay, I hope I've CCed this to all the right people. First off, to Marv, and Jaques (everyone else, you don't need this info):the patch file applied needs to be applied to the alsa source to export the symbols. (previous version tried to patch the same file twice-- sound/ is a link to alsa-kernel/) the agrsm tarball is the driver for the modem, modified to work with new alsa versions (thanks to José) and with my fixes to remove the GPL-only symbols in agrsoftmodem.c. This was done with some use of #ifdef NONGPL, so that if the NONGPL flag is defined (comments at beginning of file), these symbols are re-inserted. This allows the modules to be built and loaded on newer kernels without the need to change the module licence from Proprietary to GPL and violating the GPL. (So we can now put it on the linmodems site) These USB symbols are NOT needed for functioning of the 11c11040 modem. (and those with USB modems are better off using other drivers anyway).
------------------ To everyone else:Once you have installed ALSA version 1.0.16 or greater, and verified it works,
Please follow these steps to continue: 1. Put the hda_symbols.patch file in your alsa-driver source directory.2. Run the command 'patch -p1 < hda_symbols.patch' to patch the ALSA source. (Patched file is ./alsa-kernel/pci/hda/hda_codec.c)
3. Build the patched ALSA modules. ('make')
4. Copy the file modules/snd_hda_intel.ko to /lib/modules/<your kernel
version>/kernel/sound/pci/hda/snd-hda-intel.ko
(overwrites old module, rename it if you want) 5. run 'depmod -ae'. 6. You should now have the patched module installed. Reboot to activate. ---7. Extract the attached e-mail tarball: 'tar -jxvf agrsm-HDA-20080721.tar.bz2'
8. Change to the new dir: 'cd agrsm-20080721/'
9. Build the modules. ('make module')
10. Make a directory for the newly created agere modem modules:
'sudo mkdir /lib/modules/<your kernel version>/extra/'
11. Now copy the modules here: 'sudo cp *.ko /lib/modules/<your kernel
version>/extra/'
12. run 'depmod -ae'13. Load the new modules: 'modprobe agrmodem' followed by 'modprobe agrserial' IN THAT ORDER! (If you get a complaint about unknown symbols, check the last few lines of 'dmesg' and let me know what symbol)
You should now have device node /dev/ttyAGS3. This is now your modem port. You can use it with wvdial etc. If you have any problems, please let me know and I'll do what I can to help. Bjorn. Bjorn Wielens wrote:
Okay, we seem to be gathering a following with this HOWTO for the 11c11040 modem. The current stage we're at is having built and installed either ALSA modules 1.0.16 or 1.0.17, and verifying that /proc/asound/card0/codec#1 contains correct info.I've received success reports from Roan and Menedas.If anyone needs help getting to this point, let me know soon. I plan to continue with the howto later today when I have access to the machine with the needed tarballs on it. I will publish a HOWTO html document for later useafter we've gotten everyone up and running.Bjorn. --- roan <roan@xxxxxxxx> wrote:hi i actualy have installed ALSA 1.0.17 already. the cat /proc/asound/card0/codec#1 says this: ---- $ cat /proc/asound/card0/codec#1 Codec: Generic 11c1 ID 1040 Address: 1 Vendor Id: 0x11c11040 Subsystem Id: 0x11c10001 Revision Id: 0x100200 Modem Function Group: 0x1 ---- On Sun, 20 Jul 2008 08:22:38 -0300 Bjorn Wielens <Uniacke1@xxxxxxxx> wrote:11C11040Hi Everyone, Marv has asked me to help you with the Ageregoing tomodem that is causing plenty of grief. If you have one, and can't get it working, I'mclutterdo my best to help you below. (Lets try to do this in one thread, to keep listversiondown.) First off, please make sure you have the latestitsof ALSA drivers installed.You can get this from the ALSA site, http://www.alsa-project.org/The file is called alsa-driver-1.0.17.tar.bz2. Once you've downloaded it, change to the directory(or youin and do the following:tar -jxvf alsa-driver-1.0.17.tar.bz2 cd alsa-driver-1.0.17/ ./configure make sudo make installat this point the drivers should be installed. Now, reboot your machine to load the new driversswitchingcan manually use modprobe to add/remove, afterthisto runlevel 3)After reboot, open a terminal, and 'cat /proc/asound/card0/codec#1'Your output should be as follows: Codec: LSI ID 1040 Address : 1 Vendor ID: 11c11040 Subsystem ID <your subsystem> Revision Id: your revision Modem Function Group: 0x1 Let me know if you have any problems getting togottenstage, and I'll do my best to help you. Once we've2.6.24-19-genericeveryone to this point, we'll continue. Bjorn. Marvin Stodolsky wrote:Bjorn, Would you please work with both Menedas having Ubuntu Linux versionwith a 11c11040 Roan, having a 11c11040 and 2.6.24-19-generic orlater.becauseConcerning the License issue for 2.6.25 and laterkernels,I have found that with the Proprietary Lincenseretained,changing in agrsoftmodem.c the line #define USB_MODEM 1 to /* #define USB_MODEM 1 */blocks the usage of the USB code section, the agrmodem.ko compile is successfulHowever the 2nd stage agrserial.ko still failsof License problems. MarvS --- agrsoftmodem.c 2008-07-09 22:47:16.000000000-040022:13:07.000000000+++ agrsoftmodem.c.orig 2008-07-09-0400 @@ -17,7 +17,7 @@ #ifndef AGERE_SOFT_MODEM #define AGERE_SOFT_MODEM #endif -/* #define USB_MODEM 1 */ +#define USB_MODEM 1 //bala-dbg //#include <linux/config.h> if the terminal USB section of agrsoftmodem.c isdeleted,the compile into agrsoftmodem.o However, the On Sat, Jul 19, 2008 at 6:35 PM, Antonio Olivares <olivares14031@xxxxxxxxx> wrote:Download the files:http://linmodems.technion.ac.il/packages/ltmodem/11c11040/agere_modem.tar.gzhttp://linmodems.technion.ac.il/packages/ltmodem/11c11040/hda_symbols.patchread the filehttp://linmodems.technion.ac.il/packages/ltmodem/11c11040/11c11040.txthasGetting the modem to work is a hard feat, Josenot triedsucceeded, Bjorn has succeeded and others haveanymore. Take a look at the threadhttp://www.nabble.com/Agere-11c11040-success-with-ALSA-1.0.17-to18484945.htmlIt will hopefully guide you to success. Regards, Antonio --- On Sat, 7/19/08, menedas <menedas@xxxxxxxx>wrote:8.04? IFrom: menedas <menedas@xxxxxxxx> Subject: How to run the modem? To: discuss@xxxxxxxxxxxxx Date: Saturday, July 19, 2008, 2:47 PM Hallo, can you help me to run my modem under Ubuntuhave tried with no success the Linuxant driver andthesl-modem-daemon package. In Windows its name is"AgereSystems HDA Modem". Here is the line from the Hardware Info fromWindows:HDAUDIO\FUNC_02&VEN_11C1&DEV_1040&SUBSYS_2118144D&REV_1002\4&2DF9E19E&0&0101The modem is in the Samsung R60plus notebook. Thank you very much for your help.__________________________________________________________Gesendet von Yahoo! Mail. Dem pfiffigeren Posteingang. http://de.overview.mail.yahoo.com--- Professional hosting for everyone - http://www.host.ru__________________________________________________________________ Reclaim your name @ymail.com or @rocketmail.com. Get your new email address now! Go to http://ca.promos.yahoo.com/jacko/
Attachment:
agrsm-HDA-20080721.tar.bz2
Description: application/bzip
diff -ru alsa-driver-1.0.15/alsa-kernel/pci/hda/hda_codec.c alsa-driver-1.0.15-mod/alsa-kernel/pci/hda/hda_codec.c --- alsa-driver-1.0.15/alsa-kernel/pci/hda/hda_codec.c 2008-06-25 09:19:24.000000000 +0000 +++ alsa-driver-1.0.15-mod/alsa-kernel/pci/hda/hda_codec.c 2008-06-24 12:23:17.000000000 +0000 @@ -102,6 +102,8 @@ return res; } +EXPORT_SYMBOL(snd_hda_codec_read); + /** * snd_hda_codec_write - send a single command without waiting for response * @codec: the HDA codec @@ -126,6 +128,8 @@ return err; } +EXPORT_SYMBOL(snd_hda_codec_write); + /** * snd_hda_sequence_write - sequence writes * @codec: the HDA codec diff -ru alsa-driver-1.0.15/sound/pci/hda/hda_codec.c alsa-driver-1.0.15-mod/sound/pci/hda/hda_codec.c --- alsa-driver-1.0.15/sound/pci/hda/hda_codec.c 2008-06-25 09:19:15.000000000 +0000 +++ alsa-driver-1.0.15-mod/sound/pci/hda/hda_codec.c 2008-06-24 12:28:28.000000000 +0000 @@ -102,6 +102,8 @@ return res; } +EXPORT_SYMBOL(snd_hda_codec_read); + /** * snd_hda_codec_write - send a single command without waiting for response * @codec: the HDA codec @@ -126,6 +128,8 @@ return err; } +EXPORT_SYMBOL(snd_hda_codec_write); + /** * snd_hda_sequence_write - sequence writes * @codec: the HDA codec
