Thanks again Marvin, you were right, and you were right!! I don't need PCI hotplugging and blacklisting the sbshc module helped the boot process complete!! Takes quite a bit longer than it used to, but it completes cleanly (nothing exciting in dmesg). Two interesting questions remain: 1) What's the root cause of slamr interfering with sbshc 2) Are you ever off duty :-) Thanks again Marvin - could not have done it without you!!! Ekkehard On Sunday 01 June 2008 12:32:50 pm you wrote: > try blacklisting modules not cogent to your System with > $ sudo gedit /etc/modprobe.d/blacklist.local > # begins comment lines. Each line has form: > # blacklist Not_needed_ModuleName, for example > blacklist sbshc > # sbshc is for PCI hotplugging, which mostly like you don't need > > Save, reboot and retest. > > MarvS > > On 6/1/08, W. Ekkehard Blanz <ekkehard.blanz@xxxxxxxxx> wrote: > > Thanks Marvin, > > > > I have tried the suggestions - no difference :-( > > > > Even if I set DONTSTART in /etc/default/sl-modem-daemon to 1, the boot > > hangs. It hangs at: > > [ 34.996516 ] slamr: module license 'smart link Ltd.' taints kernel. > > [ 35.054118 ] slamr: SmartLink AMRM) modem. > > [ 35.054695] slamr: probe 2000:2800 SL2800 card ... > > [ 35.054759 ] ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 21 (level,low) > > -> IRQ 16 > > > > ((Would a tainted kernel prevent booting??????)) > > > > then > > > > $ sudo /etc/init.d/sl-modem-daemon start > > > > gives me > > Not starting SmartLink modem daemon (options not set in > > /etc/default/slmodemd) duh - OK - so I set DONSTART again to 0 and get > > > > $ sudo /etc/init.d/sl-modem-daemon start > > > > Starting SmartLink Modem driver for: slamr0. > > Creating /dev/modem symlink, pointing to: /dev/ttySL0. > > > > Nothing causing any excitement there. > > > > My interrupts are (while sl-modem-daemon is not started): > > CPU0 > > 0: 163 IO-APIC-edge timer > > 1: 809 IO-APIC-edge i8042 > > 3: 2 IO-APIC-edge > > 4: 2 IO-APIC-edge > > 6: 5 IO-APIC-edge floppy > > 7: 0 IO-APIC-edge parport0 > > 8: 23 IO-APIC-edge rtc > > 9: 0 IO-APIC-fasteoi acpi > > 10: 0 IO-APIC-edge MPU401 UART > > 12: 13384 IO-APIC-edge i8042 > > 14: 17076 IO-APIC-edge libata > > 15: 10503 IO-APIC-edge libata > > 16: 0 IO-APIC-fasteoi SL2800 > > 17: 33883 IO-APIC-fasteoi uhci_hcd:usb1, uhci_hcd:usb4, > > r128@pci:0000:01:00.0 > > 18: 166 IO-APIC-fasteoi uhci_hcd:usb2 > > 19: 0 IO-APIC-fasteoi uhci_hcd:usb3 > > 20: 3 IO-APIC-fasteoi ehci_hcd:usb5 > > 21: 1516 IO-APIC-fasteoi eth0 > > 22: 17554 IO-APIC-fasteoi Intel ICH5 > > NMI: 0 Non-maskable interrupts > > LOC: 88172 Local timer interrupts > > RES: 0 Rescheduling interrupts > > CAL: 0 function call interrupts > > TLB: 0 TLB shootdowns > > TRM: 0 Thermal event interrupts > > SPU: 0 Spurious interrupts > > ERR: 0 > > MIS: 0 > > > > Don't know who set the IRQ 16... > > > > > > Finally, the output of lsmod without the sl-modem-daemon started (when > > the daemon is started the "used by" column of slamr changes to "2") is: > > > > Module Size Used by > > af_packet 23812 2 > > rfcomm 41744 2 > > l2cap 25728 13 rfcomm > > bluetooth 61156 4 rfcomm,l2cap > > r128 41344 2 > > drm 82580 3 r128 > > ppdev 10372 0 > > ipv6 267780 10 > > speedstep_lib 6532 0 > > cpufreq_conservative 8712 0 > > cpufreq_powersave 2688 0 > > cpufreq_userspace 5284 0 > > cpufreq_stats 7104 0 > > cpufreq_ondemand 9740 0 > > freq_table 5536 2 cpufreq_stats,cpufreq_ondemand > > video 19856 0 > > output 4736 1 video > > sbs 15112 0 > > sbshc 7680 1 sbs > > container 5632 0 > > dock 11280 0 > > battery 14212 0 > > iptable_filter 3840 0 > > ip_tables 14820 1 iptable_filter > > x_tables 16132 1 ip_tables > > aes_i586 33536 0 > > dm_crypt 15364 0 > > dm_mod 62660 1 dm_crypt > > ac 6916 0 > > lp 12324 0 > > quickcam_messenger 14468 0 > > usbvideo 28676 1 quickcam_messenger > > compat_ioctl32 2304 1 usbvideo > > videodev 29440 1 usbvideo > > v4l2_common 18304 1 videodev > > v4l1_compat 15492 1 videodev > > snd_usb_audio 83936 1 > > snd_usb_lib 18432 1 snd_usb_audio > > usblp 15872 0 > > snd_hwdep 10500 1 snd_usb_audio > > slamr 433448 0 > > ungrab_winmodem 3584 0 > > snd_mpu401 9448 0 > > snd_mpu401_uart 9728 1 snd_mpu401 > > snd_seq_dummy 4868 0 > > snd_seq_oss 35584 0 > > serio_raw 7940 0 > > snd_seq_midi 9376 0 > > snd_intel8x0 35356 4 > > snd_ac97_codec 101028 1 snd_intel8x0 > > snd_rawmidi 25760 3 snd_usb_lib,snd_mpu401_uart,snd_seq_midi > > psmouse 40336 0 > > ac97_bus 3072 1 snd_ac97_codec > > snd_pcm_oss 42144 0 > > snd_mixer_oss 17920 1 snd_pcm_oss > > snd_seq_midi_event 8320 2 snd_seq_oss,snd_seq_midi > > snd_pcm 78596 5 > > snd_usb_audio,snd_intel8x0,snd_ac97_codec,snd_pcm_oss > > snd_seq 54224 6 > > snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event > > snd_timer 24836 3 snd_pcm,snd_seq > > snd_seq_device 9612 5 > > snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq > > button 9232 0 > > snd 56996 24 > > > > snd_usb_audio,snd_usb_lib,snd_hwdep,snd_mpu401,snd_mpu401_uart,snd_seq_du > >mmy,snd_seq_oss,snd_intel8x0,snd_ac97_codec,snd_rawmidi,snd_pcm_oss,snd_mi > >xer_oss,snd_pcm,snd_seq,snd_timer,snd_seq_device evdev > > 13056 4 > > shpchp 34452 0 > > pci_hotplug 30880 1 shpchp > > intel_agp 25492 1 > > agpgart 34760 2 drm,intel_agp > > iTCO_wdt 13092 0 > > iTCO_vendor_support 4868 1 iTCO_wdt > > analog 13600 0 > > parport_pc 36260 1 > > parport 37832 3 ppdev,lp,parport_pc > > snd_page_alloc 11400 2 snd_intel8x0,snd_pcm > > soundcore 8800 1 snd > > pcspkr 4224 0 > > gameport 16008 1 analog > > ext3 136712 3 > > jbd 48404 1 ext3 > > mbcache 9600 1 ext3 > > sg 36880 0 > > sr_mod 17956 0 > > cdrom 37408 1 sr_mod > > sd_mod 30720 8 > > pata_acpi 8320 0 > > ata_piix 19588 6 > > floppy 59588 0 > > ata_generic 8324 0 > > libata 159344 3 pata_acpi,ata_piix,ata_generic > > skge 43536 0 > > scsi_mod 151436 4 sg,sr_mod,sd_mod,libata > > ehci_hcd 37900 0 > > uhci_hcd 27024 0 > > usbcore 146028 8 > > > > quickcam_messenger,usbvideo,snd_usb_audio,snd_usb_lib,usblp,ehci_hcd,uhci > >_hcd thermal 16796 0 > > processor 36872 1 thermal > > fan 5636 0 > > fbcon 42912 0 > > tileblit 3456 1 fbcon > > font 9472 1 fbcon > > bitblit 6784 1 fbcon > > softcursor 3072 1 bitblit > > fuse 50580 5 > > > > On Wednesday 28 May 2008 08:08:41 pm you wrote: > > > Ekkehard, > > > > > > There is a file /etc/default/sl-modem-daemon > > > which can be edited with: > > > $ sudo gedit /etc/default/sl-modem-daemon > > > > > > If you set the line like (I'm not under Linux now) > > > DONT_START=1 > > > and reboot, the modem will not autoset and you might be able to do a > > > normal bootup. > > > > > > Afterward you can check the effect of starting the modem with: > > > $ sudo /etc/init.d/sl-modem-daemon start > > > > > > related commands are > > > $ sudo /etc/init.d/sl-modem-daemon stop > > > $ sudo /etc/init.d/sl-modem-daemon restart > > > > > > MarvS > > > > > > On Wed, May 28, 2008 at 9:30 PM, Marvin Stodolsky > > > > > > <marvin.stodolsky@xxxxxxxxx> wrote: > > > > Ekkehard > > > > > > > > RE: > error: mdm setup: cannot open dev `/dev/slamr0': Device or > > > > resource > > > > > > > >> busy error: cannot setup device `/dev/slamr0' > > > > > > > > This is because the bootup sl-modem-daemon scripts have already > > > > setup the modem. > > > > > > > > Do your bootup with as few external devices attached as possible. > > > > Then what are the outputs of: > > > > $ cat /proc/interrupts > > > > $ lsmod > > > > The object is to block loading of non-essential modules > > > > > > > > > > > > > > > > MarvS > > > > > > > > On Wed, May 28, 2008 at 5:18 PM, W. Ekkehard Blanz > > > > > > > > <ekkehard.blanz@xxxxxxxxx> wrote: > > > >> Hmmm > > > >> > > > >> I installed the new slamr that was made available only minutes > > > >> after the existence of the new kernel headers was pointed out(!!!). > > > >> I ran setup and it detected the modem just fine again. Not sure > > > >> if and how this is related, but now I am having trouble booting > > > >> into 2.6.24-17 at all - only works via recovery mode. But then it > > > >> works, and efax sends faxes (albeit with the same timeout error > > > >> messages it had before). > > > >> > > > >> sudo slmodemd -c USA /dev/slamr0 > > > >> still gives me > > > >> error: mdm setup: cannot open dev `/dev/slamr0': Device or resource > > > >> busy error: cannot setup device `/dev/slamr0' > > > >> > > > >> Here is the output of dmesg: > > > >> > > > >> ------------------------------------------------------------------- > > > >>----- ---------------------------------------- [ 0.000000] > > > >> Initializing cgroup subsys cpuset > > > >> [ 0.000000] Initializing cgroup subsys cpu > > > >> [ 0.000000] Linux version 2.6.24-17-generic (buildd@palmer) (gcc > > > >> version 4.2.3 (Ubuntu 4.2.3-2ubuntu7)) #1 SMP Thu May 1 14:31:33 > > > >> UTC 2008 (Ubuntu 2.6.24-17.31-generic) > > > >> [ 0.000000] BIOS-provided physical RAM map: > > > >> [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 > > > >> (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - > > > >> 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: > > > >> 00000000000e8000 - > > > >> 0000000000100000 (reserved) [ 0.000000] BIOS-e820: > > > >> 0000000000100000 - 000000007ffb0000 (usable) [ 0.000000] > > > >> BIOS-e820: 000000007ffb0000 - 000000007ffc0000 (ACPI data) [ > > > >> 0.000000] BIOS-e820: > > > >> 000000007ffc0000 - 000000007fff0000 (ACPI NVS) [ 0.000000] > > > >> BIOS-e820: 000000007fff0000 - 0000000080000000 (reserved) [ > > > >> 0.000000] BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved) > > > >> [ 0.000000] 1151MB HIGHMEM available. > > > >> [ 0.000000] 896MB LOWMEM available. > > > >> [ 0.000000] found SMP MP-table at 000ff780 > > > >> [ 0.000000] Entering add_active_range(0, 0, 524208) 0 entries of > > > >> 256 used [ 0.000000] Zone PFN ranges: > > > >> [ 0.000000] DMA 0 -> 4096 > > > >> [ 0.000000] Normal 4096 -> 229376 > > > >> [ 0.000000] HighMem 229376 -> 524208 > > > >> [ 0.000000] Movable zone start PFN for each node > > > >> [ 0.000000] early_node_map[1] active PFN ranges > > > >> [ 0.000000] 0: 0 -> 524208 > > > >> [ 0.000000] On node 0 totalpages: 524208 > > > >> [ 0.000000] DMA zone: 32 pages used for memmap > > > >> [ 0.000000] DMA zone: 0 pages reserved > > > >> [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 > > > >> [ 0.000000] Normal zone: 1760 pages used for memmap > > > >> [ 0.000000] Normal zone: 223520 pages, LIFO batch:31 > > > >> [ 0.000000] HighMem zone: 2303 pages used for memmap > > > >> [ 0.000000] HighMem zone: 292529 pages, LIFO batch:31 > > > >> [ 0.000000] Movable zone: 0 pages used for memmap > > > >> [ 0.000000] DMI 2.3 present. > > > >> [ 0.000000] ACPI: RSDP signature @ 0xC00FAD60 checksum 0 > > > >> [ 0.000000] ACPI: RSDP 000FAD60, 0014 (r0 ACPIAM) > > > >> [ 0.000000] ACPI: RSDT 7FFB0000, 0030 (r1 A M I OEMRSDT > > > >> 12000513 MSFT 97) > > > >> [ 0.000000] ACPI: FACP 7FFB0200, 0081 (r2 A M I OEMFACP > > > >> 12000513 MSFT 97) > > > >> [ 0.000000] ACPI: DSDT 7FFB03F0, 3763 (r1 A0049 A0049000 > > > >> 0 INTL 2002026) > > > >> [ 0.000000] ACPI: FACS 7FFC0000, 0040 > > > >> [ 0.000000] ACPI: APIC 7FFB0390, 005C (r1 A M I OEMAPIC > > > >> 12000513 MSFT 97) > > > >> [ 0.000000] ACPI: OEMB 7FFC0040, 003F (r1 A M I OEMBIOS > > > >> 12000513 MSFT 97) > > > >> [ 0.000000] ACPI: PM-Timer IO Port: 0x808 > > > >> [ 0.000000] ACPI: Local APIC address 0xfee00000 > > > >> [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) > > > >> [ 0.000000] Processor #0 15:3 APIC version 20 > > > >> [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) > > > >> [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] > > > >> gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 32, > > > >> address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus > > > >> 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR > > > >> (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 > > > >> used by override. > > > >> [ 0.000000] ACPI: IRQ2 used by override. > > > >> [ 0.000000] ACPI: IRQ9 used by override. > > > >> [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs > > > >> [ 0.000000] Using ACPI (MADT) for SMP configuration information > > > >> [ 0.000000] Allocating PCI resources starting at 88000000 (gap: > > > >> 80000000:7fb80000) > > > >> [ 0.000000] swsusp: Registered nosave memory region: > > > >> 000000000009f000 - 00000000000a0000 > > > >> [ 0.000000] swsusp: Registered nosave memory region: > > > >> 00000000000a0000 - 00000000000e8000 > > > >> [ 0.000000] swsusp: Registered nosave memory region: > > > >> 00000000000e8000 - 0000000000100000 > > > >> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping > > > >> on. Total pages: 520113 > > > >> [ 0.000000] Kernel command line: > > > >> root=UUID=d3729b53-8482-49fe-893a-75cf9dae78ae ro single > > > >> [ 0.000000] mapped APIC to ffffb000 (fee00000) > > > >> [ 0.000000] mapped IOAPIC to ffffa000 (fec00000) > > > >> [ 0.000000] Enabling fast FPU save and restore... done. > > > >> [ 0.000000] Enabling unmasked SIMD FPU exception support... > > > >> done. [ 0.000000] Initializing CPU#0 > > > >> [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 > > > >> bytes) [ 0.000000] Detected 2806.541 MHz processor. > > > >> [ 12.573543] Console: colour VGA+ 80x25 > > > >> [ 12.573547] console [tty0] enabled > > > >> [ 12.576747] Dentry cache hash table entries: 131072 (order: 7, > > > >> 524288 bytes) > > > >> [ 12.577416] Inode-cache hash table entries: 65536 (order: 6, > > > >> 262144 bytes) [ 12.701682] Memory: 2066560k/2096832k available > > > >> (2176k kernel code, 29048k reserved, 1007k data, 368k init, > > > >> 1179328k highmem) [ 12.701760] virtual kernel memory layout: > > > >> [ 12.701762] fixmap : 0xfff4b000 - 0xfffff000 ( 720 kB) > > > >> [ 12.701763] pkmap : 0xff800000 - 0xffc00000 (4096 kB) > > > >> [ 12.701764] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) > > > >> [ 12.701765] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) > > > >> [ 12.701766] .init : 0xc0421000 - 0xc047d000 ( 368 kB) > > > >> [ 12.701767] .data : 0xc0320134 - 0xc041bdc4 (1007 kB) > > > >> [ 12.701768] .text : 0xc0100000 - 0xc0320134 (2176 kB) > > > >> [ 12.702151] Checking if this processor honours the WP bit even > > > >> in supervisor mode... Ok. > > > >> [ 12.702304] SLUB: Genslabs=11, HWalign=64, Order=0-1, > > > >> MinObjects=4, CPUs=1, Nodes=1 > > > >> [ 12.782199] Calibrating delay using timer specific routine.. > > > >> 5617.80 BogoMIPS (lpj=11235612) > > > >> [ 12.782328] Security Framework initialized > > > >> [ 12.782382] SELinux: Disabled at boot. > > > >> [ 12.782448] AppArmor: AppArmor initialized > > > >> [ 12.782500] Failure registering capabilities with primary > > > >> security module. [ 12.782559] Mount-cache hash table entries: 512 > > > >> [ 12.782773] Initializing cgroup subsys ns > > > >> [ 12.782826] Initializing cgroup subsys cpuacct > > > >> [ 12.782887] CPU: After generic identify, caps: bfebfbff 00000000 > > > >> 00000000 00000000 0000441d 00000000 00000000 00000000 > > > >> [ 12.782897] monitor/mwait feature present. > > > >> [ 12.782947] using mwait in idle threads. > > > >> [ 12.783000] CPU: Trace cache: 12K uops, L1 D cache: 16K > > > >> [ 12.783086] CPU: L2 cache: 1024K > > > >> [ 12.783134] CPU: Hyper-Threading is disabled > > > >> [ 12.783182] CPU: After all inits, caps: bfebfbff 00000000 > > > >> 00000000 0000b180 0000441d 00000000 00000000 00000000 > > > >> [ 12.783196] Compat vDSO mapped to ffffe000. > > > >> [ 12.783262] Checking 'hlt' instruction... OK. > > > >> [ 12.798743] SMP alternatives: switching to UP code > > > >> [ 12.800844] Freeing SMP alternatives: 11k freed > > > >> [ 12.801023] Early unpacking initramfs... done > > > >> [ 13.130858] ACPI: Core revision 20070126 > > > >> [ 13.130958] ACPI: Looking for DSDT in initramfs... error, file > > > >> /DSDT.aml not found. > > > >> [ 13.133097] CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 04 > > > >> [ 13.133256] Total of 1 processors activated (5617.80 BogoMIPS). > > > >> [ 13.133448] ENABLING IO-APIC IRQs > > > >> [ 13.133672] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 > > > >> [ 13.281075] Brought up 1 CPUs > > > >> [ 13.281145] CPU0 attaching sched-domain: > > > >> [ 13.281149] domain 0: span 01 > > > >> [ 13.281151] groups: 01 > > > >> [ 13.281347] net_namespace: 64 bytes > > > >> [ 13.281406] Booting paravirtualized kernel on bare hardware > > > >> [ 13.282042] Time: 13:51:51 Date: 05/28/08 > > > >> [ 13.282117] NET: Registered protocol family 16 > > > >> [ 13.282407] EISA bus registered > > > >> [ 13.282476] ACPI: bus type pci registered > > > >> [ 13.282708] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last > > > >> bus=2 [ 13.282760] PCI: Using configuration type 1 > > > >> [ 13.282809] Setting up standard PCI resources > > > >> [ 13.294366] ACPI: EC: Look up EC in DSDT > > > >> [ 13.298755] ACPI: Interpreter enabled > > > >> [ 13.298806] ACPI: (supports S0 S1 S3 S4 S5) > > > >> [ 13.299038] ACPI: Using IOAPIC for interrupt routing > > > >> [ 13.307614] ACPI: PCI Root Bridge [PCI0] (0000:00) > > > >> [ 13.308198] Force enabled HPET at base address 0xfed00000 > > > >> [ 13.308207] PCI quirk: region 0800-087f claimed by ICH4 > > > >> ACPI/GPIO/TCO [ 13.308261] PCI quirk: region 0480-04bf claimed by > > > >> ICH4 GPIO [ 13.308819] PCI: Transparent bridge - 0000:00:1e.0 > > > >> [ 13.308894] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > > > >> [ 13.309028] ACPI: PCI Interrupt Routing Table > > > >> [\_SB_.PCI0.P0P4._PRT] [ 13.315258] ACPI: PCI Interrupt Link > > > >> [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) > > > >> [ 13.315823] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 > > > >> *11 12 14 15) > > > >> [ 13.316386] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 > > > >> *11 12 14 15) > > > >> [ 13.316975] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 > > > >> 11 12 14 15) > > > >> [ 13.317538] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 > > > >> 11 12 14 15) *0, disabled. > > > >> [ 13.318177] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 > > > >> 11 12 14 15) > > > >> [ 13.318746] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 > > > >> *11 12 14 15) > > > >> [ 13.319311] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 > > > >> 11 12 14 15) > > > >> [ 13.319895] ACPI Warning (tbutils-0217): Incorrect checksum in > > > >> table [OEMB] - C1, should be 91 [20070126] > > > >> [ 13.320030] Linux Plug and Play Support v0.97 (c) Adam Belay > > > >> [ 13.320114] pnp: PnP ACPI init > > > >> [ 13.320169] ACPI: bus type pnp registered > > > >> [ 13.325212] pnp: PnP ACPI: found 17 devices > > > >> [ 13.325262] ACPI: ACPI bus type pnp unregistered > > > >> [ 13.325313] ASUS P4P800 detected. Disabling PnPBIOS > > > >> [ 13.325361] PnPBIOS: Disabled > > > >> [ 13.325682] PCI: Using ACPI for IRQ routing > > > >> [ 13.325731] PCI: If a device doesn't work, try "pci=routeirq". > > > >> If it helps, post a report > > > >> [ 13.340903] NET: Registered protocol family 8 > > > >> [ 13.340952] NET: Registered protocol family 20 > > > >> [ 13.341114] hpet clockevent registered > > > >> [ 13.341121] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 > > > >> [ 13.341307] hpet0: 3 64-bit timers, 14318180 Hz > > > >> [ 13.342397] AppArmor: AppArmor Filesystem Enabled > > > >> [ 13.344877] Time: tsc clocksource has been installed. > > > >> [ 13.352912] system 00:0d: ioport range 0x680-0x6ff has been > > > >> reserved [ 13.352963] system 00:0d: ioport range 0x290-0x297 has > > > >> been reserved [ 13.353018] system 00:0e: ioport range 0x4d0-0x4d1 > > > >> has been reserved [ 13.353069] system 00:0e: ioport range > > > >> 0x800-0x87f has been reserved [ 13.353122] system 00:0e: ioport > > > >> range 0x480-0x4bf has been reserved [ 13.353173] system 00:0e: > > > >> iomem range 0xfed20000-0xfed8ffff has been reserved > > > >> [ 13.353225] system 00:0e: iomem range 0xffb00000-0xffbfffff > > > >> could not be reserved > > > >> [ 13.353288] system 00:0f: iomem range 0xfec00000-0xfec00fff has > > > >> been reserved > > > >> [ 13.353340] system 00:0f: iomem range 0xfee00000-0xfee00fff has > > > >> been reserved > > > >> [ 13.353396] system 00:10: iomem range 0x0-0x9ffff could not be > > > >> reserved [ 13.353447] system 00:10: iomem range 0xc0000-0xdffff > > > >> could not be reserved [ 13.353499] system 00:10: iomem range > > > >> 0xe0000-0xfffff could not be reserved [ 13.353551] system 00:10: > > > >> iomem range 0x100000-0x7ffeffff could not be reserved > > > >> [ 13.353610] system 00:10: iomem range 0xfff00000-0xffffffff > > > >> could not be reserved > > > >> [ 13.384091] PCI: Bridge: 0000:00:01.0 > > > >> [ 13.384140] IO window: c000-cfff > > > >> [ 13.384191] MEM window: fe900000-fe9fffff > > > >> [ 13.384241] PREFETCH window: edf00000-f5efffff > > > >> [ 13.384294] PCI: Bridge: 0000:00:1e.0 > > > >> [ 13.384342] IO window: d000-dfff > > > >> [ 13.384391] MEM window: fea00000-feafffff > > > >> [ 13.384441] PREFETCH window: f5f00000-f7efffff > > > >> [ 13.384506] PCI: Setting latency timer of device 0000:00:1e.0 to > > > >> 64 [ 13.384518] NET: Registered protocol family 2 > > > >> [ 13.420777] IP route cache hash table entries: 32768 (order: 5, > > > >> 131072 bytes) > > > >> [ 13.421196] TCP established hash table entries: 131072 (order: > > > >> 8, 1048576 bytes) > > > >> [ 13.422033] TCP bind hash table entries: 65536 (order: 7, 524288 > > > >> bytes) [ 13.422689] TCP: Hash tables configured (established > > > >> 131072 bind 65536) [ 13.422741] TCP reno registered > > > >> [ 13.432878] checking if image is initramfs... it is > > > >> [ 13.843704] Switched to high resolution mode on CPU 0 > > > >> [ 14.077997] Freeing initrd memory: 7703k freed > > > >> [ 14.078845] audit: initializing netlink socket (disabled) > > > >> [ 14.078912] audit(1211982711.272:1): initialized > > > >> [ 14.079224] highmem bounce pool size: 64 pages > > > >> [ 14.081453] VFS: Disk quotas dquot_6.5.1 > > > >> [ 14.081579] Dquot-cache hash table entries: 1024 (order 0, 4096 > > > >> bytes) [ 14.081782] io scheduler noop registered > > > >> [ 14.081831] io scheduler anticipatory registered > > > >> [ 14.081879] io scheduler deadline registered > > > >> [ 14.081936] io scheduler cfq registered (default) > > > >> [ 14.082070] Boot video device is 0000:01:00.0 > > > >> [ 14.082400] isapnp: Scanning for PnP cards... > > > >> [ 14.433600] isapnp: No Plug & Play device found > > > >> [ 14.468274] Real Time Clock Driver v1.12ac > > > >> [ 14.468437] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, > > > >> IRQ sharing enabled > > > >> [ 14.468617] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > > > >> [ 14.468806] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A > > > >> [ 14.470500] 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > > > >> [ 14.470861] 00:08: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A > > > >> [ 14.471143] ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 21 > > > >> (level, low) -> IRQ 16 > > > >> [ 14.471243] ACPI: PCI interrupt for device 0000:02:09.0 disabled > > > >> [ 14.472029] RAMDISK driver initialized: 16 RAM disks of 65536K > > > >> size 1024 blocksize > > > >> [ 14.472167] input: Macintosh mouse button emulation > > > >> as /devices/virtual/input/input0 > > > >> [ 14.472348] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at > > > >> 0x60,0x64 irq 1,12 > > > >> [ 14.474496] serio: i8042 KBD port at 0x60,0x64 irq 1 > > > >> [ 14.474549] serio: i8042 AUX port at 0x60,0x64 irq 12 > > > >> [ 14.482274] mice: PS/2 mouse device common for all mice > > > >> [ 14.482456] EISA: Probing bus 0 at eisa.0 > > > >> [ 14.482539] EISA: Detected 0 cards. > > > >> [ 14.482588] cpuidle: using governor ladder > > > >> [ 14.482635] cpuidle: using governor menu > > > >> [ 14.482770] NET: Registered protocol family 1 > > > >> [ 14.482848] Using IPI No-Shortcut mode > > > >> [ 14.482928] registered taskstats version 1 > > > >> [ 14.483069] Magic number: 8:814:888 > > > >> [ 14.483182] hash matches device ptyuf > > > >> [ 14.483257] hash matches device 0000:00:1f.1 > > > >> [ 14.483317] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found > > > >> [ 14.483367] EDD information not available. > > > >> [ 14.483770] Freeing unused kernel memory: 368k freed > > > >> [ 14.510080] input: AT Translated Set 2 keyboard > > > >> as /devices/platform/i8042/serio0/input/input1 > > > >> [ 14.705365] fuse init (API version 7.9) > > > >> [ 14.730588] ACPI Exception (processor_core-0816): AE_NOT_FOUND, > > > >> Processor Device is not present [20070126] > > > >> [ 15.332671] usbcore: registered new interface driver usbfs > > > >> [ 15.332754] usbcore: registered new interface driver hub > > > >> [ 15.348065] usbcore: registered new device driver usb > > > >> [ 15.358096] USB Universal Host Controller Interface driver v3.0 > > > >> [ 15.358226] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 > > > >> (level, low) -> IRQ 17 > > > >> [ 15.358330] PCI: Setting latency timer of device 0000:00:1d.0 to > > > >> 64 [ 15.358334] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ > > > >> 15.358670] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned > > > >> bus number 1 > > > >> [ 15.358756] uhci_hcd 0000:00:1d.0: irq 17, io base 0x0000eec0 > > > >> [ 15.358960] usb usb1: configuration #1 chosen from 1 choice > > > >> [ 15.359037] hub 1-0:1.0: USB hub found > > > >> [ 15.359089] hub 1-0:1.0: 2 ports detected > > > >> [ 15.426086] SCSI subsystem initialized > > > >> [ 15.459923] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 > > > >> (level, low) -> IRQ 18 > > > >> [ 15.460034] PCI: Setting latency timer of device 0000:00:1d.1 to > > > >> 64 [ 15.460038] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ > > > >> 15.460113] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned > > > >> bus number 2 > > > >> [ 15.460199] uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000ef00 > > > >> [ 15.460370] usb usb2: configuration #1 chosen from 1 choice > > > >> [ 15.460452] hub 2-0:1.0: USB hub found > > > >> [ 15.460504] hub 2-0:1.0: 2 ports detected > > > >> [ 15.495650] libata version 3.00 loaded. > > > >> [ 15.563645] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 > > > >> (level, low) -> IRQ 19 > > > >> [ 15.563757] PCI: Setting latency timer of device 0000:00:1d.2 to > > > >> 64 [ 15.563761] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ > > > >> 15.563837] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned > > > >> bus number 3 > > > >> [ 15.563922] uhci_hcd 0000:00:1d.2: irq 19, io base 0x0000ef20 > > > >> [ 15.564097] usb usb3: configuration #1 chosen from 1 choice > > > >> [ 15.564175] hub 3-0:1.0: USB hub found > > > >> [ 15.564227] hub 3-0:1.0: 2 ports detected > > > >> [ 15.607796] Floppy drive(s): fd0 is 1.44M > > > >> [ 15.627123] FDC 0 is a post-1991 82077 > > > >> [ 15.667382] ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 > > > >> (level, low) -> IRQ 17 > > > >> [ 15.667495] PCI: Setting latency timer of device 0000:00:1d.3 to > > > >> 64 [ 15.667500] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ > > > >> 15.667580] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned > > > >> bus number 4 > > > >> [ 15.667662] uhci_hcd 0000:00:1d.3: irq 17, io base 0x0000ef40 > > > >> [ 15.667840] usb usb4: configuration #1 chosen from 1 choice > > > >> [ 15.667919] hub 4-0:1.0: USB hub found > > > >> [ 15.667971] hub 4-0:1.0: 2 ports detected > > > >> [ 15.699184] usb 1-2: new full speed USB device using uhci_hcd > > > >> and address 2 [ 15.771262] ACPI: PCI Interrupt 0000:00:1d.7[D] -> > > > >> GSI 23 (level, low) -> IRQ 20 > > > >> [ 15.771376] PCI: Setting latency timer of device 0000:00:1d.7 to > > > >> 64 [ 15.771380] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ > > > >> 15.771457] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned > > > >> bus number 5 > > > >> [ 15.775422] ehci_hcd 0000:00:1d.7: debug port 1 > > > >> [ 15.775476] PCI: cache line size of 128 is not supported by > > > >> device 0000:00:1d.7 > > > >> [ 15.775487] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xfebff800 > > > >> [ 15.822899] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, > > > >> driver 10 Dec 2004 > > > >> [ 15.823117] usb usb5: configuration #1 chosen from 1 choice > > > >> [ 15.823197] hub 5-0:1.0: USB hub found > > > >> [ 15.823251] hub 5-0:1.0: 8 ports detected > > > >> [ 15.926899] ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 22 > > > >> (level, low) -> IRQ 21 > > > >> [ 15.927034] skge 1.13 addr 0xfeafc000 irq 21 chip Yukon-Lite rev > > > >> 9 [ 15.927384] skge eth0: addr 00:15:f2:a6:2e:12 > > > >> [ 15.932289] ata_piix 0000:00:1f.1: version 2.12 > > > >> [ 15.932307] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) > > > >> [ 15.932366] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 > > > >> (level, low) -> IRQ 19 > > > >> [ 15.932511] PCI: Setting latency timer of device 0000:00:1f.1 to > > > >> 64 [ 15.933392] scsi0 : ata_piix > > > >> [ 15.934245] scsi1 : ata_piix > > > >> [ 15.935982] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma > > > >> 0xfc00 irq 14 [ 15.936035] ata2: PATA max UDMA/100 cmd 0x170 ctl > > > >> 0x376 bmdma 0xfc08 irq 15 [ 16.114938] ata1.00: ATA-6: > > > >> IC35L060AVV207-0, V22OA63A, max UDMA/100 [ 16.114997] ata1.00: > > > >> 120103200 sectors, multi 16: LBA48 [ 16.116457] ata1.01: ATA-6: > > > >> WDC WD2500BB-55GUA0, 08.02D08, max UDMA/100 [ 16.116512] ata1.01: > > > >> 488397168 sectors, multi 16: LBA48 [ 16.138742] ata1.00: > > > >> configured for UDMA/100 > > > >> [ 16.155715] ata1.01: configured for UDMA/100 > > > >> [ 16.217921] usb 1-2: device not accepting address 2, error -71 > > > >> [ 16.637216] ata2.00: ATAPI: PIONEER DVD-RW DVR-105, 1.00, max > > > >> UDMA/33 [ 16.637300] ata2.01: ATAPI: ATAPI CDROM, V100Y, max > > > >> UDMA/33 [ 16.808729] ata2.00: configured for UDMA/33 > > > >> [ 16.980320] ata2.01: configured for UDMA/33 > > > >> [ 16.980508] scsi 0:0:0:0: Direct-Access ATA > > > >> IC35L060AVV207-0 V22O PQ: 0 ANSI: 5 > > > >> [ 16.980981] scsi 0:0:1:0: Direct-Access ATA WDC > > > >> WD2500BB-55G 08.0 PQ: 0 ANSI: 5 > > > >> [ 16.987038] scsi 1:0:0:0: CD-ROM PIONEER DVD-RW > > > >> DVR-105 1.00 PQ: 0 ANSI: 5 > > > >> [ 16.987502] scsi 1:0:1:0: CD-ROM ATAPI > > > >> CDROM. 100Y PQ: 0 ANSI: 5 > > > >> [ 17.002907] Driver 'sd' needs updating - please use bus_type > > > >> methods [ 17.003068] sd 0:0:0:0: [sda] 120103200 512-byte > > > >> hardware sectors (61493 MB) > > > >> [ 17.003136] sd 0:0:0:0: [sda] Write Protect is off > > > >> [ 17.003186] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > > > >> [ 17.003210] sd 0:0:0:0: [sda] Write cache: enabled, read cache: > > > >> enabled, doesn't support DPO or FUA > > > >> [ 17.003326] sd 0:0:0:0: [sda] 120103200 512-byte hardware > > > >> sectors (61493 MB) > > > >> [ 17.003389] sd 0:0:0:0: [sda] Write Protect is off > > > >> [ 17.003439] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 > > > >> [ 17.003461] sd 0:0:0:0: [sda] Write cache: enabled, read cache: > > > >> enabled, doesn't support DPO or FUA > > > >> [ 17.003525] sda:<4>Driver 'sr' needs updating - please use > > > >> bus_type methods > > > >> [ 17.016296] sda1 > > > >> [ 17.016443] sd 0:0:0:0: [sda] Attached SCSI disk > > > >> [ 17.016564] sd 0:0:1:0: [sdb] 488397168 512-byte hardware > > > >> sectors (250059 MB) > > > >> [ 17.016631] sd 0:0:1:0: [sdb] Write Protect is off > > > >> [ 17.016681] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00 > > > >> [ 17.016706] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: > > > >> enabled, doesn't support DPO or FUA > > > >> [ 17.016816] sd 0:0:1:0: [sdb] 488397168 512-byte hardware > > > >> sectors (250059 MB) > > > >> [ 17.016880] sd 0:0:1:0: [sdb] Write Protect is off > > > >> [ 17.016929] sd 0:0:1:0: [sdb] Mode Sense: 00 3a 00 00 > > > >> [ 17.016952] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: > > > >> enabled, doesn't support DPO or FUA > > > >> [ 17.017015] sdb: sdb1 sdb2 sdb3 < sdb5 sdb6 > sdb4 > > > >> [ 17.079995] sd 0:0:1:0: [sdb] Attached SCSI disk > > > >> [ 17.090615] sd 0:0:0:0: Attached scsi generic sg0 type 0 > > > >> [ 17.090695] sd 0:0:1:0: Attached scsi generic sg1 type 0 > > > >> [ 17.090765] sr 1:0:0:0: Attached scsi generic sg2 type 5 > > > >> [ 17.090834] scsi 1:0:1:0: Attached scsi generic sg3 type 5 > > > >> [ 17.116990] sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 > > > >> cdda tray [ 17.117051] Uniform CD-ROM driver Revision: 3.20 > > > >> [ 17.117156] sr 1:0:0:0: Attached scsi CD-ROM sr0 > > > >> [ 17.119755] usb 1-2: new full speed USB device using uhci_hcd > > > >> and address 4 [ 17.120512] sr1: scsi3-mmc drive: 0x/0x cd/rw > > > >> xa/form2 cdda tray [ 17.120617] sr 1:0:1:0: Attached scsi CD-ROM > > > >> sr1 > > > >> [ 17.296921] usb 1-2: configuration #1 chosen from 1 choice > > > >> [ 17.538724] usb 2-1: new full speed USB device using uhci_hcd > > > >> and address 2 [ 17.725517] usb 2-1: configuration #1 chosen from > > > >> 1 choice [ 17.848417] Attempting manual resume > > > >> [ 17.848468] swsusp: Resume From Partition 8:21 > > > >> [ 17.848470] PM: Checking swsusp image. > > > >> [ 17.848639] PM: Resume from disk failed. > > > >> [ 17.887142] kjournald starting. Commit interval 5 seconds > > > >> [ 17.887210] EXT3-fs: mounted filesystem with ordered data mode. > > > >> [ 28.150969] input: PC Speaker as > > > >> /devices/platform/pcspkr/input/input2 [ 28.355091] parport_pc > > > >> 00:0a: reported by Plug and Play ACPI [ 28.355192] parport0: > > > >> PC-style at 0x378, irq 7 [PCSPP,TRISTATE] [ 28.357573] parport0: > > > >> Printer, Brother HL-5250DN series > > > >> [ 28.420366] iTCO_vendor_support: vendor-support=0 > > > >> [ 28.464373] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 > > > >> (26-Jul-2007) [ 28.464530] iTCO_wdt: Found a ICH5 or ICH5R TCO > > > >> device (Version=1, TCOBASE=0x0860) > > > >> [ 28.464623] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) > > > >> [ 28.603970] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > > > >> [ 28.655190] shpchp: Standard Hot Plug PCI Controller Driver > > > >> version: 0.4 [ 28.719630] Linux agpgart interface v0.102 > > > >> [ 28.767574] agpgart: Detected an Intel 865 Chipset. > > > >> [ 28.771325] agpgart: AGP aperture is 64M @ 0xf8000000 > > > >> [ 28.947061] intel_rng: FWH not detected > > > >> [ 28.961203] input: Power Button (FF) as > > > >> /devices/virtual/input/input3 [ 28.987002] ACPI: Power Button > > > >> (FF) [PWRF] > > > >> [ 28.987146] input: Power Button (CM) as > > > >> /devices/virtual/input/input4 [ 29.018977] ACPI: Power Button > > > >> (CM) [PWRB] > > > >> [ 29.656118] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 > > > >> (level, low) -> IRQ 22 > > > >> [ 29.656243] PCI: Setting latency timer of device 0000:00:1f.5 to > > > >> 64 [ 30.080312] intel8x0_measure_ac97_clock: measured 56014 usecs > > > >> [ 30.080370] intel8x0: clocking to 48000 > > > >> [ 30.122463] input: ImExPS/2 Generic Explorer Mouse > > > >> as /devices/platform/i8042/serio1/input/input5 > > > >> [ 30.528458] slamr: module license 'Smart Link Ltd.' taints > > > >> kernel. [ 30.567156] slamr: SmartLink AMRMO modem. > > > >> [ 30.567312] slamr: probe 2000:2800 SL2800 card... > > > >> [ 30.567376] ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 21 > > > >> (level, low) -> IRQ 16 > > > >> [ 30.567936] slamr: slamr0 is SL2800 card. > > > >> [ 30.993473] usblp0: USB Bidirectional printer dev 4 if 0 alt 0 > > > >> proto 2 vid 0x04A9 pid 0x1051 > > > >> [ 30.993565] usbcore: registered new interface driver usblp > > > >> [ 31.062825] Linux video capture interface: v2.00 > > > >> [ 31.070106] usbcore: registered new interface driver > > > >> snd-usb-audio [ > > > >> 31.096226] > > > >> /build/buildd/linux-2.6.24/drivers/media/video/usbvideo/quickcam_me > > > >>sseng er.c: Logitech Quickcam Messenger USB v0.01 > > > >> [ 31.143586] videodev: "QCM USB Camera" has no release callback. > > > >> Please fix your driver for proper sysfs support, see > > > >> http://lwn.net/Articles/36850/ [ > > > >> 31.143664] > > > >> /build/buildd/linux-2.6.24/drivers/media/video/usbvideo/usbvideo.c: > > > >> QCM on /dev/video0: canvas=320x240 videosize=320x240 > > > >> [ 31.143795] input: QCM button > > > >> as /devices/pci0000:00/0000:00:1d.1/usb2/2-1/input/input6 > > > >> [ 31.157782] usbcore: registered new interface driver QCM > > > >> [ 32.806254] lp0: using parport0 (interrupt-driven). > > > >> [ 32.879866] Adding 2000084k swap on /dev/sdb5. Priority:-1 > > > >> extents:1 across:2000084k > > > >> [ 33.402020] EXT3 FS on sdb2, internal journal > > > >> [ 33.549434] device-mapper: uevent: version 1.0.3 > > > >> [ 33.549471] device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) > > > >> initialised: dm-devel@xxxxxxxxxx > > > >> [ 34.534321] kjournald starting. Commit interval 5 seconds > > > >> [ 34.534755] EXT3 FS on sdb6, internal journal > > > >> [ 34.534760] EXT3-fs: mounted filesystem with ordered data mode. > > > >> [ 34.570270] kjournald starting. Commit interval 5 seconds > > > >> [ 34.570743] EXT3 FS on sdb4, internal journal > > > >> [ 34.570748] EXT3-fs: mounted filesystem with ordered data mode. > > > >> [ 35.661793] ip_tables: (C) 2000-2006 Netfilter Core Team > > > >> [ 48.082372] No dock devices found. > > > >> [ 50.114114] NET: Registered protocol family 10 > > > >> [ 50.114640] lo: Disabled Privacy Extensions > > > >> [ 50.802109] ppdev: user-space parallel port driver > > > >> [ 51.035852] audit(1212007948.400:2): type=1503 > > > >> operation="inode_permission" requested_mask="a::" denied_mask="a::" > > > >> name="/dev/tty" pid=5425 profile="/usr/sbin/cupsd" > > > >> namespace="default" [ 51.157228] apm: BIOS version 1.2 Flags 0x03 > > > >> (Driver version 1.16ac) [ 51.157235] apm: overridden by ACPI. > > > >> [ 51.737626] [drm] Initialized drm 1.1.0 20060810 > > > >> [ 51.755482] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 > > > >> (level, low) -> IRQ 17 > > > >> [ 51.756209] [drm] Initialized r128 2.5.0 20030725 on minor 0 > > > >> [ 51.757102] agpgart: Found an AGP 3.0 compliant device at > > > >> 0000:00:00.0. [ 51.757328] agpgart: Device is in legacy mode, > > > >> falling back to 2.x [ 51.757338] agpgart: Putting AGP V2 device > > > >> at 0000:00:00.0 into 1x mode [ 51.757372] agpgart: Putting AGP V2 > > > >> device at 0000:01:00.0 into 1x mode [ 54.885397] skge eth0: > > > >> enabling interface > > > >> [ 54.890037] ADDRCONF(NETDEV_UP): eth0: link is not ready > > > >> [ 55.106397] Bluetooth: Core ver 2.11 > > > >> [ 55.107184] NET: Registered protocol family 31 > > > >> [ 55.107188] Bluetooth: HCI device and connection manager > > > >> initialized [ 55.107193] Bluetooth: HCI socket layer initialized > > > >> [ 55.231852] Bluetooth: L2CAP ver 2.9 > > > >> [ 55.231859] Bluetooth: L2CAP socket layer initialized > > > >> [ 55.292061] Bluetooth: RFCOMM socket layer initialized > > > >> [ 55.292080] Bluetooth: RFCOMM TTY layer initialized > > > >> [ 55.292083] Bluetooth: RFCOMM ver 1.8 > > > >> [ 56.793371] skge eth0: Link is up at 100 Mbps, full duplex, flow > > > >> control none > > > >> [ 56.794825] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > > > >> [ 59.193711] NET: Registered protocol family 17 > > > >> [ 71.966695] eth0: no IPv6 routers present
