Joe, Try putting an X3 (dial without diaktone detection) in your Init2 line: Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0 This is commonly necessary in Italy because of low line volatages. It that doesn't work, try Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +MS=34 which will help on noisy lines but slow speed. It that does work try the faster: Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +MS=90 The default is +MS=92, bu t is not well implemented at some IPs MarvS On Sat, May 3, 2008 at 10:19 AM, joe-5@xxxxxxxxx <joe-5@xxxxxxxxx> wrote: > Hello, I'm here again, trying to set up another (old) pc. > I have already installed the package > hcfpcimodem_1.15full_k2.6.22_14_generic_ubuntu_i386.deb and gnome-ppp > recognizes the modem as /dev/ttySHCF0. > But WVdial says that the line is busy... Prefix is 0039 (Italy) and phone > number is 7007000055 (libero.it) > Below I send ModemData.txt and the Connection log of gnome-ppp: > Thankyou very much > Joe > > ************* > ModemData.txt: > ************* > Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List > Server, > as HTML can contain viruses. Use as the email Subject Line: > YourName, YourCountry kernel 2.6.22-14-generic > With this Subject Line cogent experts will be alerted, and useful case > names left in the Archive. > YourCountry will enable Country specific guidance. Your contry's local > Linux experts > can be found through: http://www.linux.org/groups/index.html. > They will know your Country's modem code, which may be essential for dialup > service. > Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an Internet > Provider mail filters. > So in a day, also check the Archived responses at http://www.linmodems.org > -------------------------- System information ---------------------------- > CPU=i686, Linux version 2.6.22-14-generic (buildd@palmer) (gcc version > 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 > 23:05:12 GMT 2007 > scanModem update of: 2008_03_31 > > There are no blacklisted modem drivers in /etc/modprobe* files > USB modem not detected by lsusb > > For candidate card in slot 00:14.0, firmware information and bootup > diagnostics are: > PCI slot PCI ID SubsystemID Name > ---------- --------- --------- -------------- > 00:14.0 127a:1005 122d:4006 Serial controller: Rockwell > International HCF 56k Data/Fax/Voice/Spkp > > Modem interrupt assignment and sharing: > 9: 2021 XT-PIC-XT uhci_hcd:usb1 > --- Bootup diagnostics for card in PCI slot 00:14.0 ---- > [ 33.590382] PCI: Found IRQ 9 for device 0000:00:14.0 > [ 39.599434] PCI: Sharing IRQ 9 with 0000:00:14.0 > [ 60.056157] PCI: Sharing IRQ 9 with 0000:00:14.0 > > === Finished firmware and bootup diagnostics, next deducing cogent > software. === > > Predictive diagnostics for card in bus 00:14.0: > Modem chipset detected on > CLASS="Class 0700: 127a:1005" > NAME="Serial controller: Rockwell International HCF 56k Data/Fax/Voice/Spkp > " > PCIDEV=127a:1005 > SUBSYS=122d:4006 > IRQ=9 > IDENT=hcflinmodem > > For candidate modem in: 00:14.0 > Class 0700: 127a:1005 Serial controller: Rockwell International HCF 56k > Data/Fax/Voice/Spkp > Primary PCI_id 127a:1005 > Support type needed or chipset: hcflinmodem > > > ----------------end Softmodem section -------------- > > For owners of a Dell PCs with Conexant HSF modems, a driver source package > with full speed enabled is available, but requires driver compiling. Read > Conexant.txt > > Read Conexant.txt > > Writing Conexant.txt > > > Completed candidate modem analyses. > > The base of the UDEV device file system is: /dev/.udev > > Versions adequately match for the compiler installed: 4.1.3 > and the compiler used in kernel assembly: 4.1.3 > > > > Minimal compiling resources appear complete: > make utility - /usr/bin/make > Compiler version 4.1 > linuc_headers base folder /lib/modules/2.6.22-14-generic/build > > However some compilations and executable functions may need additional > files, > in the FileNames.h (so called kernel "h"eaders) collection installed in > /usr/include/ . > For martian_modem, additional required packages are libc6-dev (and for > Debian/Ubuntu, linux-libc-dev). The also required headers of package libc6 > are commonly installed by default. > > > > If a driver compilation fails, with message including some lack of some > FileName.h (stdio.h for example), then > Some additional kernel-header files need installation to /usr/include. The > minimal additional packages are libc6-dev > and any of its dependents, under Ubuntu linux-libc-dev > > If an alternate ethernet connection is available, > $ apt-get update > $ apt-get -s install linux-kernel-devel > will install needed package > For Debian/Ubuntu related distributions, run the following command to > display the needed package list: > > Otherwise packages have to be found through http://packages.ubuntu.com > Once downloaded and transferred into a Linux partition, > they can be installed alltogether with: > $ sudo dpkg -i *.deb > > > Checking pppd properties: > -rwsr-xr-- 1 root dip 269256 2007-10-04 21:57 /usr/sbin/pppd > > In case of an "error 17" "serial loopback" problem, see: > http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html > > To enable dialout without Root permission do: > $ su - root (not for Ubuntu) > sudo chmod a+x /usr/sbin/pppd > or under Ubuntu related Linuxes > sudo chmod a+x /usr/sbin/pppd > > Checking settings of: /etc/ppp/options > asyncmap 0 > noauth > crtscts > lock > hide-password > modem > proxyarp > lcp-echo-interval 30 > lcp-echo-failure 4 > noipx > > In case of a message like: > Warning: Could not modify /etc/ppp/pap-secrets: Permission denied > see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html > > > Don't worry about the following, it is for the experts > should trouble shooting be necessary. > ========================================================== > > Checking for modem support lines: > -------------------------------------- > /device/modem symbolic link: slmodemd created symbolic link > /dev/ttySL0: Within /etc/udev/ files: > > Within /etc/modprobe.conf files: > /etc/modprobe.d/blacklist-modem:# Uncomment these entries in order to > blacklist unwanted modem drivers > /etc/modprobe.d/blacklist-modem:# blacklist snd-atiixp-modem > /etc/modprobe.d/blacklist-modem:# blacklist snd-via82xx-modem > /etc/modprobe.d/alsa-base:options snd-atiixp-modem index=-2 > /etc/modprobe.d/alsa-base:options snd-via82xx-modem index=-2 > Within any ancient /etc/devfs files: > > Within ancient kernel 2.4.n /etc/module.conf files: > > --------- end modem support lines -------- > > > > > ************* > Connection log of gnome-ppp: > ************* > /home/bibi/.wvdial.conf<Warn>: Ignoring malformed input line: ";Do NOT edit > this file by hand!" > WvDial<*1>: WvDial: Internet dialer version 1.56 > WvModem<*1>: Cannot set information for serial port. > WvDial<*1>: Initializing modem. > WvDial<*1>: Sending: ATZ > WvDial Modem<*1>: ATZ > WvDial Modem<*1>: OK > WvDial<*1>: Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > WvDial Modem<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > WvDial Modem<*1>: OK > WvDial<*1>: Modem initialized. > WvDial<*1>: Sending: ATM1L3DT0039,7007000055 > WvDial<*1>: Waiting for carrier. > WvDial Modem<*1>: ATM1L3DT0039,7007000055 > WvDial Modem<*1>: BUSY > WvDial<Warn>: The line is busy. Trying again. > WvDial<*1>: Sending: ATM1L3DT0039,7007000055 > WvDial<*1>: Waiting for carrier. > WvDial Modem<*1>: ATM1L3DT0039,7007000055 > WvDial Modem<*1>: BUSY > WvDial<Warn>: The line is busy. Trying again. > > [...many attempts...] > > WvDial<*1>: Sending: ATM1L3DT0039,7007000055 > WvDial<*1>: Waiting for carrier. > WvDial Modem<*1>: ATM1L3DT0039,7007000055 > WvDial Modem<*1>: BUSY > WvDial<Warn>: The line is busy. Trying again. > WvDial<*1>: Sending: ATM1L3DT0039,7007000055 > WvDial<*1>: Waiting for carrier. > WvDial Modem<*1>: ATM1L3DT0039,7007000055 > WvDial Modem<*1>: NO CARRIER > WvDial<Warn>: No Carrier! Trying again. > WvDial<Warn>: Maximum Attempts Exceeded..Aborting!! > WvDial<*1>: Disconnecting at Sat May 3 16:02:56 2008 > > > >
