Re: Emanuele, Italy kernel 2.6.22-14-generic

[Emanuele Pagone <epagone@xxxxxxxxxxxxx>]

Antonio,

thank you for your help. Unfortunately replacing +FCLASS=0 to +MS=90 or 
+MS=34 in the Init2 string, don't make any difference: still "NO 
DIALTONE" message.

Looking at the "Linmodem Post Install Problems" in the "troubleshooting" 
section, I found this interesting suggestion:

> 3. NO DIALTONE message: please check your IRQ's, wrong, or conflicting.
> Use setserial -agv /dev/modem and cat /proc/interrupts, the latter
> should not show the IRQ reported by the former.

but setserial is not available in my system ("bash: setserial: command 
not found") :\

> emanuele@emanuele-desktop:~$ setserial -agv /dev/modem
> Il programma «setserial» non è attualmente installato.  È possibile installarlo digitando:
> sudo apt-get install setserial
> bash: setserial: command not found
> emanuele@emanuele-desktop:~$ cat /proc/interrupts
>            CPU0       CPU1       
>   0:        156          0   IO-APIC-edge      timer
>   1:       9015          0   IO-APIC-edge      i8042
>   6:          5          0   IO-APIC-edge      floppy
>   7:          0          0   IO-APIC-edge      parport0
>   8:          3          0   IO-APIC-edge      rtc
>   9:          1          0   IO-APIC-fasteoi   acpi
>  10:          0          0   IO-APIC-edge      MPU401 UART
>  12:     164053          0   IO-APIC-edge      i8042
>  14:      64493          0   IO-APIC-edge      libata
>  15:     145204          0   IO-APIC-edge      libata
>  16:      14471          0   IO-APIC-fasteoi   SL1800
>  17:          2          0   IO-APIC-fasteoi   ehci_hcd:usb1
>  18:     451126          0   IO-APIC-fasteoi   uhci_hcd:usb2, uhci_hcd:usb5, radeon@pci:0000:01:00.0
>  19:          0          0   IO-APIC-fasteoi   uhci_hcd:usb3
>  20:       1016          0   IO-APIC-fasteoi   uhci_hcd:usb4, libata
>  21:        749          0   IO-APIC-fasteoi   eth0
>  22:        388          0   IO-APIC-fasteoi   Intel ICH5
> NMI:          0          0 
> LOC:     259493     221273 
> ERR:          0
> MIS:          0


For what concerns the following suggestion, instead:

> 4. Still NO DIALTONE: edit /etc/wvdial.conf. By default it shows place holders
> or text for 3 Init strings (you can add more up to 7). Try to add
> ATH1 as last command in last non empty string. Return to step vwdial.

I got (I think --- and hope! --- that the addition of the ATM0 command 
it's not important)

> emanuele@emanuele-desktop:~$ sudo wvdial
> WvDial<*1>: WvDial: Internet dialer version 1.56
> WvModem<*1>: Cannot get information for serial port.
> WvDial<*1>: Initializing modem.
> WvDial<*1>: Sending: ATZ
> WvDial Modem<*1>: ATZ
> WvDial Modem<*1>: OK
> WvDial<*1>: Sending: ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0
> WvDial Modem<*1>: ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0
> WvDial Modem<*1>: OK
> WvDial<*1>: Sending: ATM0 ATH1
> WvDial Modem<*1>: ATM0 ATH1
> WvDial<*1>: Sending: ATQ0
> WvDial Modem<*1>: NO CARRIER
> WvDial<*1>: Re-Sending: ATM0 ATH1
> WvDial Modem<*1>: ATM0 ATH1
> WvDial<Err>: Modem not responding.

Now I don't have no more the "NO DIALTONE" error, but things don't look 
better. Equal results are obtained using +MS=90 or +MS=34 in place of 
+FCLASS=0.

I hope that someone understands why my modem don't dial if the 
installation process seems ok...

Thanks, bye.


Emanuele


Antonio Olivares ha scritto:
> ----- Original Message ----
> From: Emanuele Pagone <epagone@xxxxxxxxxxxxx>
> To: Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx>
> Cc: discuss@xxxxxxxxxxxxx
> Sent: Thursday, April 10, 2008 6:01:08 PM
> Subject: Re: Emanuele, Italy kernel 2.6.22-14-generic
>
> Thanks for the help, but I'm still having problems.
>
> I edited wvdial.conf and sl-modem-daemon as Marvin said, then I typed:
>
> > emanuele@emanuele-desktop:~$ ls  -l  /dev/ttySL0  /dev/pts/*
> > crw-rw---- 1 root     uucp 136, 0 2008-04-10 23:08 /dev/pts/0
> > crw--w---- 1 emanuele tty  136, 1 2008-04-10 23:31 /dev/pts/1
> > lrwxrwxrwx 1 root     root     10 2008-04-10 23:08 /dev/ttySL0 -> /dev/pts/0
>
> all seemed right.
>
> Unfortunately, when I made:
>
> > emanuele@emanuele-desktop:~$ sudo wvdial
> > WvDial<*1>: WvDial: Internet dialer version 1.56
> > WvModem<*1>: Cannot get information for serial port.
> > WvDial<*1>: Initializing modem.
> > WvDial<*1>: Sending: ATZ
> > WvDial Modem<*1>: ATZ
> > WvDial Modem<*1>: OK
> > WvDial<*1>: Sending: ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0
> > WvDial Modem<*1>: ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0
> > WvDial Modem<*1>: OK
> > WvDial<*1>: Modem initialized.
> > WvDial<*1>: Sending: ATDT0803761010
> > WvDial<*1>: Waiting for carrier.
> > WvDial Modem<*1>: ATDT0803761010
> > WvDial Modem<*1>: NO DIALTONE
> > WvDial<Err>: No dial tone.
> > WvDial<*1>: Disconnecting at Thu Apr 10 23:43:44 2008
>
> I got a "NO DIALTONE" message. This is my wvdial.conf:
>
> > emanuele@emanuele-desktop:~$ cat /etc/wvdial.conf
> >
> > [Dialer Defaults]
> > Init1 = ATZ
> > Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0
>
> Change this +FCLASS=0 to +MS=90 or +MS=34 and try the process again.  Maybe that is what you need.  
>
> Hope this helps,
>
> Antonio 
>
> > ; Init3 = ATM0
> > Modem Type = Analog Modem
> > Baud = 460800
> > New PPPD = yes
> > Modem = /dev/ttySL0
> > ISDN = 0
> > Phone = 0803761010
> > Username = REMOVED
> > Password = REMOVED
> > Carrier Check = no
> > ; Stupid Mode = yes
>
> I removed my username and password. About the phone number, the first 
> digit '0' is the first part of a regional area code (I'm not passing 
> through a switchboard to make a call): under Ms Windows, the modem works 
> perfectly using that number.
>
> I have also an ethernet card in my computer so, following what's 
> suggested in the "YourSystem.txt", I disconnected the RJ-45 cable and I 
> made:
>
> > emanuele@emanuele-desktop:~/Modem$ sudo ifconfig eth0 down
> > emanuele@emanuele-desktop:~/Modem$ ifconfig
> > lo        Link encap:Local Loopback  
> >           inet addr:127.0.0.1  Mask:255.0.0.0
> >           inet6 addr: ::1/128 Scope:Host
> >           UP LOOPBACK RUNNING  MTU:16436  Metric:1
> >           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> >           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> >           collisions:0 txqueuelen:0 
> >           RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
>
> Nothing changed. I also tried to remove the X3 command from the Init2 
> string, but the result it's just the same: "NO DIALTONE".
>
> What's wrong?
>
> Thank you.
>
>
> Emanuele
>
>
> Marvin Stodolsky ha scritto:
> > Emanuele
> >
> > Stop running the
> > $ sudo  ./setup
> > your installation is OK now
> >
> > Just do an edit:
> > $ sudo gedit /etc/wvdial.conf
> > to a final format like:
> >
> > [Dialer Defaults]
> > Init1 = ATZ
> > Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0
> > #  X3 meaning "dial without dialtone detection" is often necessary in ITALY
> > Modem Type = Analog Modem
> > Baud = 460800
> > New PPPD = yes
> > Modem = /dev/ttySL0
> > ISDN = 0
> > Phone = 3015560020
> > Username = LoginName@xxxxxxxxxxxxxxxx
> > Password = YourPassword
> > Carrier Check = no
> > # needed for /dev/pts/N  modem ports
> > ## end /etc/wvdial.conf
> >
> > Also
> > $ sudo gedit /etc/default/sl-modem-daemon
> > and change
> > SLMODEMD_COUNTRY=USA
> > to
> > SLMODEMD_COUNTRY=ITALY
> >
> > Then reboot and the modem should be automatically setup.
> > Check with
> > $ ls  -l  /dev/ttySL0  /dev/pts/*
> > whose output should include
> >     /dev/ttySL0 --> /dev/pts/SomeNumber
> >
> > If so, try dialing out with
> > $ sudo wvdial
> >
> > MarvS
> > scanModem maintainer
> >
> >
> > On Wed, Apr 9, 2008 at 6:21 PM, Emanuele Pagone <epagone@xxxxxxxxxxxxx> wrote:
> > > Jacques,
> > >
> > >  unfortunately, I'm not able to reproduce again the message that you
> > > highlighted:
> > >
> > >
> > >
> > > > The cause of the failure is in this message:
> > > > [   28.192512] slamr: device 10b9:5459 is grabbed by another driver
> > >  After sending the previous email, I tried again several times to execute "$
> > > sudo ./setup", but I wasn't able to obtain again that message, instead I got
> > > another one:
> > >
> > >
> > > > emanuele@emanuele-desktop:~/slamr-2.6.22-14-generic$ sudo ./setup
> > > >
> > > > installing drivers for kernel version 2.6.22-14-generic
> > > > driver=slamr
> > > >
> > > > Installing the Debian packages supporting autoloading
> > > > (Lettura del database ... 176085 file e directory attualmente installati.)
> > > > Mi preparo a sostituire sl-modem-daemon 2.9.10+2.9.9d+e-pre2-5ubuntu4 (con
> > > sl-modem-daemon_2.9.10+2.9.9d+e-pre2-5ubuntu4_i386.deb) ...
> > > > Shutting down SmartLink Modem driver normally probably failed.
> > > > Trying it the hard way (send SIGKILL all slmodemd processes): Unloading
> > > modem driver from kernel ... slamr.
> > > > Spacchetto il sostituto di sl-modem-daemon ...
> > > >
> > > > Configuro sl-modem-daemon (2.9.10+2.9.9d+e-pre2-5ubuntu4) ...
> > > > L'utente «Slmodemd» già esiste come utente di sistema. Uscita.
> > > > Starting SmartLink Modem driver for: slamr0.
> > > > Creating /dev/modem symlink, pointing to: /dev/ttySL0.
> > > >
> > > >
> > > > Copying over newer files
> > > > Making folder /lib/modules/2.6.22-14-generic/extra
> > > > Copying drivers to /lib/modules/2.6.22-14-generic/extra
> > > > Checking driver install
> > > > slamr.ko  slusb.ko  ungrab-winmodem.ko
> > > > Copying newer slmodemd to /usr/sbin/
> > > > Checking slmodemd version. Should be 2.9.11
> > > > SmartLink Soft Modem: version 2.9.11 May 26 2007 13:41:57
> > > > Finished installs.
> > > > Informing the System
> > > >
> > > > Starting function tests, loading drivers:
> > > > Running diagnostic:
> > > >
> > > > [  169.999471] slamr: module license 'Smart Link Ltd.' taints kernel.
> > > > [  170.006535] slamr: SmartLink AMRMO modem.
> > > > [  170.009099] slamr: probe 10b9:5459 SL1800 card...
> > > > [  170.011636] slamr: mc97 codec is SIL26
> > > > [  170.011805] slamr: slamr0 is SL1800 card.
> > > > [  807.310486] slamr: SmartLink AMRMO modem.
> > > > [  807.310936] slamr: probe 10b9:5459 SL1800 card...
> > > > [  807.313860] slamr: mc97 codec is SIL26
> > > > [  807.314046] slamr: slamr0 is SL1800 card.
> > > > [ 1383.434767] slamr: SmartLink AMRMO modem.
> > > > [ 1383.437638] slamr: probe 10b9:5459 SL1800 card...
> > > > [ 1383.439842] slamr: mc97 codec is SIL26
> > > > [ 1383.440011] slamr: slamr0 is SL1800 card.
> > > >
> > > >
> > > > ports should be created by:
> > > > slmodemd -c USA /dev/slamr0
> > > > error: mdm setup: cannot open dev `/dev/slamr0': Device or resource busy
> > > >
> > > > error: cannot setup device `/dev/slamr0'
> > > > Checking for success
> > > > Running wvdialconf
> > > > Editing `/etc/wvdial.conf'.
> > > >
> > > > Scanning your serial ports for a modem.
> > > >
> > > > ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
> > > > ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
> > > > ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
> > > > ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
> > > > ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
> > > > ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
> > > > Modem Port Scan<*1>: S2   S3   WvModem<*1>: Cannot get information for
> > > serial port.
> > > > ttySL0<*1>: ATQ0 V1 E1 -- OK
> > > > ttySL0<*1>: ATQ0 V1 E1 Z -- OK
> > > > ttySL0<*1>: ATQ0 V1 E1 S0=0 -- OK
> > > > ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
> > > > ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
> > > > ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
> > > > ttySL0<*1>: Modem Identifier: ATI -- SmartLink Soft Modem
> > > > ttySL0<*1>: Speed 4800: AT -- OK
> > > > ttySL0<*1>: Speed 9600: AT -- OK
> > > > ttySL0<*1>: Speed 19200: AT -- OK
> > > > ttySL0<*1>: Speed 38400: AT -- OK
> > > > ttySL0<*1>: Speed 57600: AT -- OK
> > > > ttySL0<*1>: Speed 115200: AT -- OK
> > > > ttySL0<*1>: Speed 230400: AT -- OK
> > > > ttySL0<*1>: Speed 460800: AT -- OK
> > > > ttySL0<*1>: Max speed is 460800; that should be safe.
> > > > ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
> > > >
> > > > Found a modem on /dev/ttySL0.
> > > > Modem configuration written to /etc/wvdial.conf.
> > > > ttySL0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
> > > > Modem detection successful
> > > > Read wdial.txt
> > > > Then edit /etc/wvdial.conf  with:
> > > > sudo gedit /etc/wvdial.conf
> > > > at the lines beginning with ; and deleting the ; < >  Then dialout with:
> > > >        sudo wvdial
> > > > Running setup again is NOT necessary. Only for dialout the:
> > > >        sudo wvdial
> > > >
> > > > Read the Slamr.txt record, other *.txt files and the sample wvdial.conf .
> > >  I'm a bit confused...
> > >
> > >  Anyway, if I do
> > >
> > >
> > > > emanuele@emanuele-desktop:~/slamr-2.6.22-14-generic$ sudo lsmod > 2>&1
> > > ungrab.problem.txt
> > > > bash: syntax error near unexpected token `2'
> > >  as you can see, I get an error.
> > >
> > >  I hope you could give me some guidance. Thank you.
> > >
> > >
> > >  Emanuele
> > >
> > >  P.S.: If you are wandering why the numbers in the list of the "Running
> > > diagnostic:" is different than the others in the previous email, it's just
> > > because the list was becoming very long (I ran "./setup" a lot of times),
> > > and I tried to obtain a "clean" list. So I opened with gvim the "setup" file
> > > and I found the "dsmeg" command, and after reading its man page, I gave
> > > "sudo dsmeg -c", restarted the computer and made just two or three attempts
> > > with "./setup"... I was just trying to learn something about linux, but I
> > > swear to be more cautious from now :) .
> > >
> > >  Jacques Goldberg ha scritto:
> > >
> > >
> > >
> > > > The cause of the failure is in this message:
> > > > [   28.192512] slamr: device 10b9:5459 is grabbed by another driver
> > > > Please do EXACTLY what follows:
> > > >
> > > > sudo lsmod > 2>&1 ungrab.problem.txt
> > > > sudo ungrab-winmodem >> 2>&1 ungrab.problem.txt
> > > > sudo modprobe slamr >> 2>&1 ungrab.problem.txt
> > > > sudo lsmod >> 2&1 ungrab.problem.txt
> > > > sudo slmodemd -c ITALY /dev/slamr0 >> 2&1 ungrab.problem.txt
> > > >
> > > > and send us the file  ungrab.problem.txt  which these five commands will
> > > produce.
> > > > Jacques
> > > >
> > > >
> > > > Emanuele Pagone wrote:
> > > >
> > > > > Jacques,
> > > > >
> > > > > your guess is right! (sorry if you didn't understand me easily, but I'm
> > > not so comfortable in writing in English...): I did not run "sudo ./setup"
> > > at all.
> > > > > Now I made it (sl-modem-daemon package is NOT installed, I removed it
> > > completely), but there are some errors:
> > > > > > emanuele@emanuele-desktop:~/slamr-2.6.22-14-generic$ sudo ./setup
> > > [sudo] password for emanuele:
> > > > > > installing drivers for kernel version 2.6.22-14-generic
> > > > > > driver=slamr
> > > > > >
> > > > > > Installing the Debian packages supporting autoloading
> > > > > > Selezionato il pacchetto sl-modem-daemon, che non lo era.
> > > > > > (Lettura del database ... 176073 file e directory attualmente
> > > installati.)
> > > > > > Spacchetto sl-modem-daemon (da
> > > sl-modem-daemon_2.9.10+2.9.9d+e-pre2-5ubuntu4_i386.deb) ...
> > > > > > Configuro sl-modem-daemon (2.9.10+2.9.9d+e-pre2-5ubuntu4) ...
> > > > > > L'utente «Slmodemd» già esiste come utente di sistema. Uscita.
> > > > > > Starting SmartLink Modem driver for: slamr0.
> > > > > > Creating /dev/modem symlink, pointing to: /dev/ttySL0.
> > > > > >
> > > > > >
> > > > > > Copying over newer files
> > > > > > Making folder /lib/modules/2.6.22-14-generic/extra
> > > > > > Copying drivers to /lib/modules/2.6.22-14-generic/extra
> > > > > > Checking driver install
> > > > > > slamr.ko  slusb.ko  ungrab-winmodem.ko
> > > > > > Copying newer slmodemd to /usr/sbin/
> > > > > > Checking slmodemd version. Should be 2.9.11
> > > > > > SmartLink Soft Modem: version 2.9.11 May 26 2007 13:41:57
> > > > > > Finished installs.
> > > > > > Informing the System
> > > > > >
> > > > > > Starting function tests, loading drivers:
> > > > > > Running diagnostic:
> > > > > >
> > > > > > [   28.186723] slamr: module license 'Smart Link Ltd.' taints kernel.
> > > > > > [   28.192496] slamr: SmartLink AMRMO modem.
> > > > > > [   28.192512] slamr: device 10b9:5459 is grabbed by another driver
> > > > > >
> > > > > > ports should be created by:
> > > > > > slmodemd -c USA /dev/slamr0
> > > > > > error: mdm setup: cannot stat `/dev/slamr0': No such file or directory
> > > > > > error: cannot setup device `/dev/slamr0'
> > > > > > Checking for success
> > > > > > Port creation with slmodemd failed.
> > > > > > Read the Slamr.txt record, other *.txt files and the sample
> > > wvdial.conf .
> > > > > I try to translate the Italian-language lines from the terminal output:
> > > > >
> > > > >
> > > > > > Selezionato il pacchetto sl-modem-daemon, che non lo era.
> > > > > > (Lettura del database ... 176073 file e directory attualmente
> > > installati.)
> > > > > > Spacchetto sl-modem-daemon (da
> > > sl-modem-daemon_2.9.10+2.9.9d+e-pre2-5ubuntu4_i386.deb) ...
> > > > > > Configuro sl-modem-daemon (2.9.10+2.9.9d+e-pre2-5ubuntu4) ...
> > > > > > L'utente «Slmodemd» già esiste come utente di sistema. Uscita.
> > > > > sl-modem-daemon package selected, it wasn't selected.
> > > > > (Reading database ... 176073 files and directories now installed.)
> > > > > Unpacking sl-modem-daemon (from
> > > sl-modem-daemon_2.9.10+2.9.9d+e-pre2-5ubuntu4_i386.deb) ...
> > > > > Configuring sl-modem-daemon (2.9.10+2.9.9d+e-pre2-5ubuntu4) ...
> > > > > «Slmodemd» user existed as system user. Exit.
> > > > >
> > > > >
> > > > > If I checked the slmodemd version, the output seems good:
> > > > >
> > > > >
> > > > > > emanuele@emanuele-desktop:~/slamr-2.6.22-14-generic$ slmodemd
> > > --version
> > > > > > SmartLink Soft Modem: version 2.9.11 May 26 2007 13:41:57
> > > > > Can I move on with the last steps:
> > > > >
> > > > >
> > > > > >  $ slmodemd --help
> > > > > >  $ slmodemd --countrylist &> Clist.txt
> > > > > >  If not in the USA, look for your COUNTRY_NAME therein.
> > > > > >  Do and edit with:
> > > > > >  $ sudo gedit  /etc/default/sl-modem-daemon
> > > > > >  and therein replace the USA in the line:
> > > > > >  SLMODEMD_COUNTRY=USA
> > > > > >  This will provide for the correct Country setting in the automated:
> > > > > >     slmodemd -c COUNTRY /dev/slamr0
> > > > > ?
> > > > >
> > > > > Thanks for your help!
> > > > >
> > > > >
> > > > > Emanuele
> > > > >
> > > > > Jacques Goldberg ha scritto:
> > > > >
> > > > > > Emanuele,
> > > > > >
> > > > > > In addition to my previous mail, I now think again and possibly did
> > > not understand what you want,
> > > > > > Can it be that you wrote your message below BEFORE having run the
> > > command    sudo ./setup   ? Or perhaps you did not run
> > > > > > sudo ./setup at all?
> > > > > >
> > > > > > The correct version of slmodemd is created and installed by the
> > > command sudo ./setup
> > > > > > slamr is a driver.
> > > > > > slmodemd is a control utility which starts the operation of the slamr
> > > driver in your case, or of several versions of the ALSA driver which are not
> > > relevant in your case.
> > > > > > The package sl-modem-daemon installs an obsolete version of slmodemd
> > > in your system.
> > > > > > sudo ./setup installs the right one at the same place.
> > > > > >
> > > > > > The package sl-modem-daemon is NOT necessary to use your modem.
> > > > > > All it does is to automatically start the program slmodemd when you
> > > boot the computer. Without sl-modem-daemon you must type
> > > > > > sudo slmodemd -c ITALY /dev/slamr0
> > > > > > and leave slmodemd running in the window where you typed the command
> > > before you can use the modem
> > > > > > sl-modem-daemon saves you the work of typing
> > > > > > sudo slmodemd -c ITALY /dev/slamr0
> > > > > >
> > > > > > Jacques
> > > > > >
> > > > > > Jacques
> > > > > >
> > > > > > Emanuele Pagone wrote:
> > > > > >
> > > > > > > Jacques,
> > > > > > >
> > > > > > > first of all, thank you for your answer.
> > > > > > >
> > > > > > > Jacques Goldberg ha scritto:
> > > > > > >
> > > > > > > > Emanuele,
> > > > > > > >
> > > > > > > > Your ModemData.txt tells you what you have to do step by step!
> > > > > > > > Have you tried to read it and apply the instructions?
> > > > > > > Yes, I read the instructions, but what makes me ask for your help is
> > > the emphatized part in the text:
> > > > > > > > The modem is supported by the Smartlink slamr driver
> > > > > > > > *plus the slmodemd helper utility.*  Read the
> > > > > > > > Smartlink.txt and Modem/YourSystem.txt for follow through
> > > guidance.
> > > > > > > Now, I don't have any slmodemd utility installed. Infact:
> > > > > > >
> > > > > > > $ slmodemd --version
> > > > > > > Il programma «slmodemd» non è attualmente installato.  È possibile
> > > installarlo digitando:
> > > > > > > sudo apt-get install sl-modem-daemon
> > > > > > > *bash: slmodemd: command not found*
> > > > > > >
> > > > > > > I read Smartlink.txt, but (for me) it's not enough clear about the
> > > way to install the slmodemd utility. I tried to install the sl-modem-daemon
> > > package (via Synaptic package manager), but if I understood correctly some
> > > previous messages, in Ubuntu there is a wrong version of the utility. To be
> > > sure about this, when I finished to install the sl-modem-daemon package, I
> > > wrote in the console:
> > > > > > > $ slmodemd --version
> > > > > > >
> > > > > > > and I got something like "2.9.9e" that should be wrong (infact in
> > > other messages I read that the right version must be 2.9.11). Am I right?
> > > > > > > I removed the slmodemd package, but now I don't know how to install
> > > the slmodemd utlity. ModemData.txt don't cover this part of the procedure.
> > > Can you help me?
> > > > > > > Thanks, bye.
> > > > > > >
> > > > > > >
> > > > > > > Emanuele
>
>
>
>
> __________________________________________________
> Do You Yahoo!?
> Tired of spam?  Yahoo! Mail has the best spam protection around 
> http://mail.yahoo.com