Antonio & Jacques-
After installing the modem I was hitting "Ctrl + C"
and I must have been turning slmodemd off.
The modem still does not dial, but "maybe" I
am getting closer. Now instead of doing Ctrl + C
I open up another terminal and when I type
$ sudo wvdialconf /etc/wvdial.conf
I get-
Scanning your serial ports for a modem.
Modem Port Scan<*1>: S0 S1 S2 S3
WvModem<*1>: Cannot get information for serial port.
ttySL0<*1>: ATQ0 V1 E1 -- OK
ttySL0<*1>: ATQ0 V1 E1 Z -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttySL0<*1>: Modem Identifier: ATI -- SmartLink Soft Modem
ttySL0<*1>: Speed 4800: AT -- OK
ttySL0<*1>: Speed 9600: AT -- OK
ttySL0<*1>: Speed 19200: AT -- OK
ttySL0<*1>: Speed 38400: AT -- OK
ttySL0<*1>: Speed 57600: AT -- OK
ttySL0<*1>: Speed 115200: AT -- OK
ttySL0<*1>: Speed 230400: AT -- OK
ttySL0<*1>: Speed 460800: AT -- OK
ttySL0<*1>: Max speed is 460800; that should be safe.
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
Found a modem on /dev/ttySL0.
Modem configuration written to /etc/wvdial.conf.
ttySL0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
And when I type
$ sudo wvdial
I get-
WvDial<*1>: WvDial: Internet dialer version 1.56
WvModem<*1>: Cannot get information for serial port.
WvDial<*1>: Initializing modem.
WvDial<*1>: Sending: ATZ
WvDial Modem<*1>: ATZ
WvDial Modem<*1>: OK
WvDial<*1>: Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
WvDial Modem<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
WvDial Modem<*1>: OK
WvDial<*1>: Modem initialized.
WvDial<Err>: Configuration does not specify a valid phone number.
WvDial<Err>: Configuration does not specify a valid login name.
WvDial<Err>: Configuration does not specify a valid password.
So I typed "wvdialconf", filled in the phone number, login name, and
password, and saved the file. But when I did "wvdial" I still got the same
response as above. Is there some trick to saving the file, or is
there more than
one wvdialconf?
Thanks for help. I am new at Linux.
Gary
Antonio-
.... and when I run
$ sudo wvdial
I get-
"WvDial<*1>: WvDial: Internet dialer version 1.56
WvDial<Err>: Cannot open /dev/modem: No such file or directory
WvDial<Err>: Cannot open /dev/modem: No such file or directory
WvDial<Err>: Cannot open /dev/modem: No such file or directory
Thanks,
Gary
Antonio-
When I run
$ sudo wvdialconf /etc/wvdial.conf
I get-
"Scanning your serial ports for a modem.
Modem Port Scan <*1>: S0 S1 S2 S3
Sorry no modem detected! Is it
in use in another program? Did you
properly configure it with setserial?"
Thanks for response,
Gary
PS - Notebook is dual boot (XP and Ubuntu).
Gary,
Everything is apparently ok. Instead of trying out GnomePPP, why not
use directly wvdial. It should find the modem port /dev/ttySL0
$ sudo wvdialconf /etc/wvdial.conf
should find the modem. Edit username, password and phone number to
dial, add a line "Carrier Check = no" to this file and try to connect
using the command line wvdial. What messages do you see? If you can
get a solid connection, then you may then alter your Gnome-ppp and
connect using it, but first use the old tried and true wvdial.
Regards,
Antonio
On 4/3/08, Gary Kaucher <gkaucher@xxxxxxx> wrote:
> I recently installed Ubuntu 7.10 (Gutsy Gibbon) on a Toshiba Satellite
> M55-S3314 notebook and I am attempting to get the modem working. Please see
> the System Information provided by ScanTool below. I followed the advice of
> ScanTool , downloaded and unpacked SLMODEMD.gcc4.1.tar.gz. and then I
> followed the advice of the 1st_Read.txt that was created and I did:
>
> # su - root
> # chmod a+x slmodemd
> # cp slmodemd /usr/sbin
>
> I then inserted an ALSA modem driver:
>
> # modprobe snd-intel8x0m
> # slmodemd --alsa -c USA modem:1
>
> and got the message
>
> "SmartLink Soft Modem version 2.9.11Feb 17,2008
> Symbolic link '/dev/ttySL0' --> '/dev/pts/1 created.
> modem 'modem:1' created. TTY is '/dev/pts/1'
> Use '/dev/ttySL0' as modem device.
>
> I thought it was successful, but after configuring the Gnome-ppp
> dialer using pppconfig, nothing at all happens when I try to dial
> out, even when I try other ports.
>
> I notice that there were other slmodemd executables that were included
> in the SLMODEMD.gcc4.1 folder. Since Ubuntu is a Debian related
> distro should I have used one of them instead?
>
>
>
> Here are the ScanTool results:
>
>
> ------------------------- System information ----------------------------
> CPU=i686,
> Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929
> (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007
> scanModem update of: 2008_03_31
> There are no blacklisted modem drivers in /etc/modprobe* files
> USB modem not detected by lsusb
> For candidate card in slot 00:1e.3, firmware information and bootup
> diagnostics are:
> PCI slot PCI ID SubsystemID Name
> ---------- --------- --------- --------------
> 00:1e.3 8086:266d 1179:0001 Modem: Intel Corporation
> 82801FB/FBM/FR/FW/FRW
> Modem interrupt assignment and sharing:
> --- Bootup diagnostics for card in PCI slot 00:1e.3 ----
> [ 10.302362] ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 20
(level, low) ->
> IRQ 18
> [ 10.302373] ACPI: PCI interrupt for device 0000:00:1e.3 disabled
> The PCI slot 00:1e.3 of the modem card may be disabled early in
> a bootup process, but then enabled later. If modem drivers load
> but the modem is not responsive, read Bootup.txt about possible fixes.
> Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx
> if help is needed.
>
>
> ===== Advanced Linux Sound Architecture (ALSA) diagnostics =====
> The ALSA packages provide audio support and also drivers for some modems.
> ALSA diagnostics are written during bootup to /proc/asound/ folders.
> The ALSA verion is 1.0.14
> The modem cards detected by "aplay -l" are:
>
> The /proc/asound/pcm file reports:
> -----------------------
> 00-04: Intel ICH - IEC958 : Intel ICH6 - IEC958 : playback 1
> 00-03: Intel ICH - ADC2 : Intel ICH6 - ADC2 : capture 1
> 00-02: Intel ICH - MIC2 ADC : Intel ICH6 - MIC2 ADC : capture 1
> 00-01: Intel ICH - MIC ADC : Intel ICH6 - MIC ADC : capture 1
> 00-00: Intel ICH : Intel ICH6 : playback 1 : capture 1
> about /proc/asound/cards:
> ------------------------
> 0 [ICH6 ]: ICH4 - Intel ICH6
> Intel ICH6 with ALC250 at irq 16
> === Finished firmware and bootup diagnostics, next deducing
cogent software.
> ===
> Predictive diagnostics for card in bus 00:1e.3:
> Modem chipset detected on
> CLASS="Class 0703: 8086:266d"
> NAME="Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW "
> PCIDEV=8086:266d
> SUBSYS=1179:0001
> IRQ=18
> SOFT=8086:266d.MC97
> CodecArchived=SIL27
> IDENT=slmodemd
> SLMODEMD_DEVICE=modem:1
> Driver=snd-intel8x0m
> For candidate modem in: 00:1e.3
> Class 0703: 8086:266d Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW
> Primary PCI_id 8086:266d
> Subsystem PCI_id 1179:0001
> Softmodem codec or chipset from diagnostics:
> from Archives: SIL27, an LSI/AgereSystems
> type
>
>
> Support type needed or chipset: slmodemd
> An ALSA (Advanced Linux Sound Architecture) modem driver: snd-intel8x0m
> provides Low Level support enabling contact with the modem hardware.
> For all BUT Conexant chip soft modems (using hsfmodem software)
> complementary High Level support is through a Smartlink utility: slmodemd
> Download from
> http://linmodems.technion.ac.il/packages/smartlink/
> the package SLMODEMD.gcc4.1.tar.gz having a compiled slmodemd.
Unpack under
> Linux with:
> $ tar zxf SLMODEMD.gcc4.1.tar.gz
> and read instructions therein. But briefly, the modem is setup with
> command:
> sudo slmodemd -c YOUR_COUNTRY --alsa modem:1
> reporting dynamic creation of ports:
> /dev/ttySL0 --> /dev/pts/N , with N some number
> Read Smartlink.txt and Modem/YourSystem.txt for follow through guidance.
> ----------------end Softmodem section --------------
> Writing Intel.txt
> Writing Smartlink.txt
> ============ end Smartlink section =====================
> Completed candidate modem analyses.
> The base of the UDEV device file system is: /dev/.udev
> Versions adequately match for the compiler installed: 4.1.3
> and the compiler used in kernel assembly: 4.1.3
>
>
> Minimal compiling resources appear complete:
> make utility - /usr/bin/make
> Compiler version 4.1
> linuc_headers base folder
> /lib/modules/2.6.22-14-generic/build
> However some compilations and executable functions may need additional
> files,
> in the FileNames.h (so called kernel "h"eaders) collection installed in
> /usr/include/ .
> For martian_modem, additional required packages are libc6-dev (and for
> Debian/Ubuntu, linux-libc-dev). The also required headers of package libc6
> are commonly installed by default.
>
> If a driver compilation fails, with message including some lack of some
> FileName.h (stdio.h for example), then
> Some additional kernel-header files need installation to /usr/include. The
> minimal additional packages are libc6-dev
> and any of its dependents, under Ubuntu linux-libc-dev
> If an alternate ethernet connection is available,
> $ apt-get update
> $ apt-get -s install linux-kernel-devel
> will install needed package
> For Debian/Ubuntu related distributions, run the following command to
> display the needed package list:
> Otherwise packages have to be found through http://packages.ubuntu.com
> Once downloaded and transferred into a Linux partition,
> they can be installed alltogether with:
> $ sudo dpkg -i *.deb
>
> Checking pppd properties:
> -rwsr-xr-- 1 root dip 269256 2007-10-04 15:57 /usr/sbin/pppd
> In case of an "error 17" "serial loopback" problem, see:
>
> http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html
> To enable dialout without Root permission do:
> $ su - root (not for Ubuntu)
> sudo chmod a+x /usr/sbin/pppd
> or under Ubuntu related Linuxes
> sudo chmod a+x /usr/sbin/pppd
> Checking settings of: /etc/ppp/options
> asyncmap 0
> noauth
> crtscts
> lock
> hide-password
> modem
> proxyarp
> lcp-echo-interval 30
> lcp-echo-failure 4
> noipx
> In case of a message like:
> Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
> see
> http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
> Read Modem/YourSystem.txt concerning other COMM channels: eth0 eth1
> eth0:avah
> Which can interfere with Browser naviagation.
> Don't worry about the following, it is for the experts
> should trouble shooting be necessary.
> ==========================================================
> Checking for modem support lines:
> --------------------------------------
> /device/modem symbolic link:
> slmodemd created symbolic link /dev/ttySL0:
> Within /etc/udev/ files:
> Within /etc/modprobe.conf files:
> /etc/modprobe.d/blacklist-modem:# Uncomment these entries
> in order to blacklist unwanted modem drivers
> /etc/modprobe.d/blacklist-modem:# blacklist
> snd-atiixp-modem
> /etc/modprobe.d/blacklist-modem:# blacklist
> snd-via82xx-modem
> /etc/modprobe.d/alsa-base:options snd-atiixp-modem index=-2
> /etc/modprobe.d/alsa-base:options snd-via82xx-modem
> index=-2
> Within any ancient /etc/devfs files:
> Within ancient kernel 2.4.n /etc/module.conf files:
> --------- end modem support lines --------
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
> --
> No virus found in this outgoing message.
> Checked by AVG Free Edition. Version: 7.5.516 / Virus Database:
> 269.22.1/1349 - Release Date: 3/29/08 5:02 PM
>
>
>
--
No virus found in this incoming message.
Checked by AVG Free Edition.
Version: 7.5.516 / Virus Database: 269.22.1/1349 - Release Date:
3/29/08 5:02 PM
--
No virus found in this incoming message.
Checked by AVG Free Edition.
Version: 7.5.516 / Virus Database: 269.22.1/1349 - Release Date:
3/29/08 5:02 PM
--
No virus found in this outgoing message.
Checked by AVG Free Edition.
Version: 7.5.516 / Virus Database: 269.22.1/1349 - Release Date: 3/29/08 5:02 PM
