It's a Serial modem connected through USB cable so its not identified with scanModem: -------------------------- System information ---------------------------- CPU=x86_64, This is Linux version 2.6.23-hardened-r7 (root@saros) (gcc version 3.4.6 (Gentoo Hardened 3.4.6-r2 p1.5, ssp-3.4.6-1.0, pie-8.7.10)) #2 SMP Tue Feb 26 18:53:09 IST $ scanModem update of: 2008_02_25 USB modem not detected by lsusb === Finished modem firmware and bootup diagnostics section. === However wvdial detected and output as follows: Scanning your serial ports for a modem. Modem Port Scan<*1>: S0 S1 S2 S3 ttyUSB0<*1>: ATQ0 V1 E1 -- OK ttyUSB0<*1>: ATQ0 V1 E1 Z -- OK ttyUSB0<*1>: ATQ0 V1 E1 S0=0 -- OK ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK ttyUSB0<*1>: Modem Identifier: ATI -- Agere OCM V.92 Ver2.7a (Jun 14 2004) Voice Mercury DP2SH mode-ii SERIAL ttyUSB0<*1>: Speed 4800: AT -- OK ttyUSB0<*1>: Speed 9600: AT -- OK ttyUSB0<*1>: Speed 19200: AT -- OK ttyUSB0<*1>: Speed 38400: AT -- OK ttyUSB0<*1>: Speed 57600: AT -- OK ttyUSB0<*1>: Speed 115200: AT -- OK ttyUSB0<*1>: Speed 230400: AT -- OK ttyUSB0<*1>: Speed 460800: AT -- Speed 460800: AT -- Speed 460800: AT -- Max speed is 230400; that should be safe. ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK Found a modem on /dev/ttyUSB0. Modem configuration written to /etc/wvdial.conf. ttyUSB0<Info>: Speed 230400; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" On Thu, Feb 28, 2008 at 1:40 AM, Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx> wrote: > Amir, > > > Browse http://linmodems.technion.ac.il and download scanModem.gz . > Within a Linux partition > gunzip scanModem.gz > To make it executable: > chmod +x scanModem > Run diagnositics with: > ./scanModem > Only the ouput ModemData.txt should be sent to Discuss@xxxxxxxxxxxxx > > MarvS > > > > On Wed, Feb 27, 2008 at 1:45 PM, Amir Levin <amir.levin@xxxxxxxxx> wrote: > > I have 2 external serial modems (Trendnet TFM-560X), working perfectly. > > > > Recently I purchased a new server which comes with only USB connections. > > So I bought a serial to USB adapter (Prolific PL2303) which has a good > > kernel support. I recompiled the kernel with driver and dmesg shows > > that the kernel found it correctly: > > > > > > Code: > > usbcore: registered new interface driver usbserial > > drivers/usb/serial/usb-serial.c: USB Serial Driver core > > drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303 > > pl2303 2-2:1.0: pl2303 converter detected > > usb 2-2: pl2303 converter now attached to ttyUSB0 > > usbcore: registered new interface driver pl2303 > > drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver > > > > When I communicate with the modem through minicom, every command > > works except ATD/ATDT: > > > > Code: > > Welcome to minicom 2.2 > > > > OPTIONS: I18n > > Compiled on Feb 26 2008, 19:24:47. > > Port /dev/ttyUSB0 > > > > AT S7=45 S0=0 L1 V1 X4 &c1 E1 Q0 > > OK > > ATI0 > > Agere OCM V.92 Ver2.7a (Jun 14 2004) Voice Mercury DP2SH mode-ii SERIAL > > OK > > ATI1 > > 0418 > > OK > > ATI4 > > 18 > > OK > > ATI5 > > OCM ,0,19 > > OK > > ATD > > ERROR > > ATDT9 > > ERROR > > > > I tested with 2 different kernels and it's just the same... > > Anyone had a similar problem? > > Any clue for a solution? > > > > Thanks. > > >
