Alright, here is an updated ModemData.txt and dmesg.txt, I hope you
mean send this to discuss@xxxxxxxxxxxxxx Thanks!!!
On 2/23/08, Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx> wrote:
> Alexei,
>
> RE:
> ================
> For candidate card in slot 02:02.0, firmware information and bootup
> diagnostics are:
> PCI slot PCI ID SubsystemID Name
> ---------- --------- --------- --------------
> 02:02.0 11c1:0620 11c1:0620 Communication controller: Agere Systems
> Unknown device 0620
>
> Modem interrupt assignment and sharing:
> --- Bootup diagnostics for card in PCI slot 02:02.0 ----
> (no 02:02.0 lines detected in dmesg buffer )
> ================
> In several cases like this, it seems that the bootup diagnostics fail
> to detect the agrmodem card at all!!. THis is with your acpi patch in
> the code. Any suggestions???
>
> Josh,
> Just after a bootup do:
> $ dmesg > dmesg.txt
> Send the List the dmesg.txt and a fresh ModemData.txt
> We need more detail on events during the bootup.
>
> MarvS
>
>
> On Sat, Feb 23, 2008 at 12:12 AM, Josh Smith <josh.a.smitty@xxxxxxxxx>
> wrote:
> > I have now also tried moving the modem to all other PCI slots and ran
> > the tests for each one, still displaying the same message. Any
> > suggestions?
> >
> >
> >
> >
> > ---------- Forwarded message ----------
> > From: Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx>
> > Date: Fri, Feb 22, 2008 at 2:16 PM
> > Subject: Re: Josh, Canada, kernel 2.6.22-14-generic
> > To: Josh Smith <josh.a.smitty@xxxxxxxxx>, discussions@xxxxxxxxxxxxx
> >
> >
> > Josh,
> >
> > All you have done is technically OK
> > -----------
> > josh@Rusty:~$ sudo modprobe agrmodem
> > josh@Rusty:~$ sudo modprobe agrserial
> > josh@Rusty:~$ sudo ln -s /dev/ttyAGS3 /dev/ttySAGR
> > josh@Rusty:~$ sudo ln -s /dev/ttyAGS3 /dev/modem
> > josh@Rusty:~$ lsmod | grep agr
> > agrserial 13984 0
> > agrmodem 1188644 1 agrserial
> > josh@Rusty:~$ sudo wvdialconf /etc/wvdial.conf
> > Editing `/etc/wvdial.conf'.
> >
> > Scanning your serial ports for a modem.
> >
> > Modem Port Scan<*1>: S0 S1 S2 S3
> > ttySAGR<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
> > ttySAGR<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
> > ttySAGR<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
> > -------------------
> >
> > You are encountering the typical problem with this modem.
> > If possible, try changing the PCI slot in which the modem is seated and
> retest.
> > Please send to the List, Not direct to me, as others have more
> > expertise with this modem
> >
> > MarvS
> >
> >
> >
> > On Fri, Feb 22, 2008 at 2:59 PM, Josh Smith <josh.a.smitty@xxxxxxxxx>
> wrote:
> > > So far I have had no luck detecting my modem. I've checked
> > > /lib/modules/2.2.6.22-14-generic/extras/ and both agrmodem.ko and
> > > agrserial.ko are present. I've also tried adding pci=noacpi to the
> > > end of the kernel line in menu.lst In the txt file I've attached is
> > > the readout from the terminal in trying to get my modem detected.
> > >
> > >
> > >
> > > On Thu, Feb 21, 2008 at 6:49 PM, Marvin Stodolsky
> > > <marvin.stodolsky@xxxxxxxxx> wrote:
> > > > Jacques
> > > > The http://linmodems.technion.ac.il/ seems to be down.
> > > >
> > > > Josh
> > > >
> > > > For candidate modem in PCI bus: 02:02.0
> > > > Class 0780: 11c1:0620 Communication controller: Agere Systems
> > > > Unknown device 0620
> > > > Primary PCI_id 11c1:0620
> > > > Support type needed or chipset: Agere.SV2P
> > > >
> > > > At http://linmodems.technion.ac.il/packages/ltmodem/sv92/
> > > > you need the agrsm-20070804.tar.gz
> > > > Download it into your Linux partition.
> > > > Unpack with
> > > > $ tar zxf agr*.tar.gz
> > > > which will create a agrsm folder. Move in with
> > > > $ cd agrsm
> > > > Look around
> > > > $ ls
> > > > Browse the doumentation. Compile with:
> > > > $ make clean
> > > > $ make
> > > > will compile the components
> > > > $ sudo make install
> > > > installs the components. Read the agrsm-howto.txt for setup
> details
> > > >
> > > > Write back if you need help.
> > > >
> > > > MarvS
> > > > scanModem maintainer
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > On Thu, Feb 21, 2008 at 1:17 PM, Josh Smith
> > <josh.a.smitty@xxxxxxxxx> wrote:
> > > > > Hey, I'm completely new to linux. I'd really appreciate it if
> you
> > > > > could help me out by directing me to what drivers I need and
> how to
> > > > > compile them if I need to. Thanks!!!
> > > > >
> > > >
> > >
> >
>
Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List Server,
as HTML can contain viruses. Use as the email Subject Line:
YourName, YourCountry kernel 2.6.22-14-generic
With this Subject Line cogent experts will be alerted, and useful case names left in the Archive.
YourCountry will enable Country specific guidance. Your contry's local Linux experts
can be found through: http://www.linux.org/groups/index.html.
They will know your Country's modem code, which may be essential for dialup service.
Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an Internet Provider mail filters.
So in a day, also check the Archived responses at http://www.linmodems.org
-------------------------- System information ----------------------------
CPU=i686,
Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007
scanModem update of: 2008_02_20
There are no blacklisted modem drivers in /etc/modprobe* files
The Advanced Linux Sound Architecture (ALSA) packages providing audio support,
also includes drivers for some modems. The ALSA diagnostics are written during
bootup to /proc/asound/ folders.
The /proc/asound/ audio+modem diagostics are being copied.
Finished copy to Modem/ALSAjosh.tgz
The ALSA verion is 1.0.14
The modem cards detected by "aplay -l" are:
The /proc/asound/pcm file reports:
-----------------------
00-02: ALC883 Analog : ALC883 Analog : capture 2
00-01: ALC883 Digital : ALC883 Digital : playback 1
00-00: ALC883 Analog : ALC883 Analog : playback 1 : capture 2
about /proc/asound/cards:
------------------------
0 [SB ]: HDA-Intel - HDA ATI SB
HDA ATI SB at 0xfe9f8000 irq 17
USB modem not detected by lsusb
For candidate card in slot 02:02.0, firmware information and bootup diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
02:02.0 11c1:0620 11c1:0620 Communication controller: Agere Systems Unknown device 0620
Modem interrupt assignment and sharing:
--- Bootup diagnostics for card in PCI slot 02:02.0 ----
For candidate card in slot 00:14.2, firmware information and bootup diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
00:14.2 1002:437b 103c:2a31 Audio device: ATI Technologies Inc SB450 HDA Audio
Modem interrupt assignment and sharing:
17: 13768 0 IO-APIC-fasteoi HDA Intel
--- Bootup diagnostics for card in PCI slot 00:14.2 ----
[ 16.956000] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 17
=== Finished modem firmware and bootup diagnostics section. ===
=== Next deducing cogent software ===
Predictive diagnostics for card in bus 02:02.0:
Modem chipset detected on
CLASS="Class 0780: 11c1:0620"
NAME="Communication controller: Agere Systems Unknown device 0620"
PCIDEV=11c1:0620
SUBSYS=11c1:0620
SUBven=11c1
IRQ=11
IDENT=Agere.SV2P
For candidate modem in: 02:02.0
Class 0780: 11c1:0620 Communication controller: Agere Systems Unknown device 0620
Primary PCI_id 11c1:0620
Support type needed or chipset: Agere.SV2P
----------------end Softmodem section --------------
Predictive diagnostics for card in bus 00:14.2:
Modem chipset not detected on
CLASS="Class 0403: 1002:437b"
NAME="Audio device: ATI Technologies Inc SB450 HDA Audio "
PCIDEV=1002:437b
SUBSYS=103c:2a31
SUBven=103c
IRQ=17
HDA=1002:437b
SOFT=1002:437b.HDA
High Definition Audio (HDA) cards MAY host a modem chip in their Subsystem,
and many are supported by the ALSA audio+modem driver snd-hda-intel
A modem was not detected on HDA card 1002:437b.
If another modem card is present, then most likely 1002:437b does not host a modem.
If another modem card has not been detected, then possibilities are:
1) A Conexant modem chip is present on 1002:437b, as Conexant chips
are frequently not detectable by ALSA diagnostics
2) The modem may be of the older non-PCI Controller Chipset (hardware) type.
Try detection with Root permission:
sudo wvdialconf /etc/wvdial.conf
For candidate modem in: 00:14.2
Class 0403: 1002:437b Audio device: ATI Technologies Inc SB450 HDA Audio
Primary PCI_id 1002:437b
Subsystem PCI_id 103c:2a31
Softmodem codec or chipset from diagnostics:
from Archives:
Lacking a dsp (digital signal processing) chip, the modem is a software
intensive or "softmodem" type. Its primary controller manages the traffic
with the CPU. But the software needed is specified in the Subsystem.
-----------------------------------------
Support type needed or chipset:
Support can likely be achieved through two mutually exclusive alternatives:
1) The hsfmodem software for Conexant chipset modems: Read Conexant.txt
The following ALSA alternative CANNOT work with Conexant modems.
2) An ALSA modem driver plus slmodemd. Read Smartlink.txt for details, and
to test get the package SLMODEMD.gcc4.1.tar.gz from:
http://linmodems.technion.ac.il/packages/smartlink/
----------------end Softmodem section --------------
Writing Smartlink.txt
============ end Smartlink section =====================
Completed candidate modem analyses.
The base of the UDEV device file system is: /dev/.udev
Versions adequately match for the compiler installed: 4.1.3
and the compiler used in kernel assembly: 4.1.3
Minimal compiling resources appear complete:
make utility - /usr/bin/make
Compiler version 4.1
linuc_headers base folder /lib/modules/2.6.22-14-generic/build
However some compilations and executable functions may need additional files,
in the FileNames.h (so called kernel "h"eaders) collection installed in /usr/include/ .
For martian_modem, additional required packages are libc6-dev (and for Debian/Ubuntu, linux-libc-dev). The also required headers of package libc6 are commonly installed by default.
If a driver compilation fails, with message including some lack of some FileName.h (stdio.h for example), then
Some additional kernel-header files need installation to /usr/include. The minimal additional packages are libc6-dev
and any of its dependents, under Ubuntu linux-libc-dev
If an alternate ethernet connection is available,
$ apt-get update
$ apt-get -s install linux-kernel-devel
will install needed package
For Debian/Ubuntu related distributions, run the following command to display the needed package list:
Otherwise packages have to be found through http://packages.ubuntu.com
Once downloaded and transferred into a Linux partition,
they can be installed alltogether with:
$ sudo dpkg -i *.deb
Checking pppd properties:
-rwsr-xr-- 1 root dip 269256 2007-10-04 13:57 /usr/sbin/pppd
In case of an "error 17" "serial loopback" problem, see:
http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html
To enable dialout without Root permission do:
$ su - root (not for Ubuntu)
sudo chmod a+x /usr/sbin/pppd
or under Ubuntu related Linuxes
sudo chmod a+x /usr/sbin/pppd
Checking settings of: /etc/ppp/options
asyncmap 0
noauth
crtscts
lock
hide-password
modem
proxyarp
lcp-echo-interval 30
lcp-echo-failure 4
noipx
In case of a message like:
Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
Read Modem/YourSystem.txt concerning other COMM channels: eth0
Which can interfere with Browser naviagation.
Don't worry about the following, it is for the experts
should trouble shooting be necessary.
==========================================================
Checking for modem support lines:
--------------------------------------
/device/modem symbolic link:
slmodemd created symbolic link /dev/ttySL0:
Within /etc/udev/ files:
/etc/udev/rules.d/10-local.rules:#ltmodem
/etc/udev/rules.d/10-local.rules:KERNEL="ttylLTM0", SYMLINK="modem"
Within /etc/modprobe.conf files:
/etc/modprobe.d/blacklist-modem:# Uncomment these entries in order to blacklist unwanted modem drivers
/etc/modprobe.d/blacklist-modem:# blacklist snd-atiixp-modem
/etc/modprobe.d/blacklist-modem:# blacklist snd-via82xx-modem
/etc/modprobe.d/alsa-base:options snd-atiixp-modem index=-2
/etc/modprobe.d/alsa-base:options snd-via82xx-modem index=-2
Within any ancient /etc/devfs files:
Within ancient kernel 2.4.n /etc/module.conf files:
ltmodem
--------- end modem support lines --------
[ 0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003bfd0000 (usable)
[ 0.000000] BIOS-e820: 000000003bfd0000 - 000000003bfde000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003bfde000 - 000000003c000000 (ACPI NVS)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
[ 0.000000] 63MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000ff780
[ 0.000000] Entering add_active_range(0, 0, 245712) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 245712
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 245712
[ 0.000000] On node 0 totalpages: 245712
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 127 pages used for memmap
[ 0.000000] HighMem zone: 16209 pages, LIFO batch:3
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP signature @ 0xC00F8A20 checksum 0
[ 0.000000] ACPI: RSDP 000F8A20, 0014 (r0 HP-CPC)
[ 0.000000] ACPI: RSDT 3BFD0000, 0034 (r1 HP-CPC OEMRSDT 2000624 MSFT 97)
[ 0.000000] ACPI: FACP 3BFD0200, 0084 (r2 HP-CPC OEMFACP 2000624 MSFT 97)
[ 0.000000] ACPI: DSDT 3BFD0440, 47A3 (r1 HP-CPC RC410-M 0 INTL 2002026)
[ 0.000000] ACPI: FACS 3BFDE000, 0040
[ 0.000000] ACPI: APIC 3BFD0390, 006C (r1 HP-CPC OEMAPIC 2000624 MSFT 97)
[ 0.000000] ACPI: MCFG 3BFD0400, 003C (r1 HP-CPC OEMMCFG 2000624 MSFT 97)
[ 0.000000] ACPI: OEMB 3BFDE040, 005B (r1 HP-CPC AMI_OEM 2000624 MSFT 97)
[ 0.000000] ATI board detected. Disabling timer routing over 8254.
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:4 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:4 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 3c000000:c2e00000)
[ 0.000000] Built 1 zonelists. Total pages: 243793
[ 0.000000] Kernel command line: root=UUID=c1c2c4f1-c231-41f3-a43e-282f4f08028f ro quiet splash
[ 0.000000] mapped APIC to ffffd000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffc000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Detected 3066.022 MHz processor.
[ 39.866196] Console: colour VGA+ 80x25
[ 39.866906] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 39.867465] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 39.888128] Memory: 962572k/982848k available (2015k kernel code, 19728k reserved, 916k data, 364k init, 65344k highmem)
[ 39.888138] virtual kernel memory layout:
[ 39.888139] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB)
[ 39.888140] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 39.888141] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 39.888142] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 39.888143] .init : 0xc03e3000 - 0xc043e000 ( 364 kB)
[ 39.888144] .data : 0xc02f7d26 - 0xc03dce84 ( 916 kB)
[ 39.888145] .text : 0xc0100000 - 0xc02f7d26 (2015 kB)
[ 39.888148] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 39.888187] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=2, Nodes=1
[ 39.967978] Calibrating delay using timer specific routine.. 6139.29 BogoMIPS (lpj=12278587)
[ 39.968004] Security Framework v1.0.0 initialized
[ 39.968009] SELinux: Disabled at boot.
[ 39.968021] Mount-cache hash table entries: 512
[ 39.968148] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000651d 00000000 00000001
[ 39.968157] monitor/mwait feature present.
[ 39.968159] using mwait in idle threads.
[ 39.968166] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 39.968169] CPU: L2 cache: 1024K
[ 39.968172] CPU: Physical Processor ID: 0
[ 39.968174] CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000651d 00000000 00000001
[ 39.968185] Compat vDSO mapped to ffffe000.
[ 39.968201] Checking 'hlt' instruction... OK.
[ 39.984037] SMP alternatives: switching to UP code
[ 39.984595] Early unpacking initramfs... done
[ 40.272764] ACPI: Core revision 20070126
[ 40.272824] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
[ 40.275632] CPU0: Intel(R) Pentium(R) 4 CPU 3.06GHz stepping 09
[ 40.275653] SMP alternatives: switching to SMP code
[ 40.275827] Booting processor 1/1 eip 3000
[ 40.616201] Initializing CPU#1
[ 40.692902] Calibrating delay using timer specific routine.. 6132.05 BogoMIPS (lpj=12264112)
[ 40.692914] CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0000651d 00000000 00000001
[ 40.692921] monitor/mwait feature present.
[ 40.692929] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 40.692932] CPU: L2 cache: 1024K
[ 40.692934] CPU: Physical Processor ID: 0
[ 40.692937] CPU: After all inits, caps: bfebfbff 20100000 00000000 0000b180 0000651d 00000000 00000001
[ 40.363214] CPU1: Intel(R) Pentium(R) 4 CPU 3.06GHz stepping 09
[ 40.363259] Total of 2 processors activated (12271.34 BogoMIPS).
[ 40.363440] ENABLING IO-APIC IRQs
[ 40.363643] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 40.403266] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
[ 40.403317] ...trying to set up timer (IRQ0) through the 8259A ... failed.
[ 40.403321] ...trying to set up timer as Virtual Wire IRQ... works.
[ 40.550370] checking TSC synchronization [CPU#0 -> CPU#1]:
[ 40.570317] Measured 1015081172 cycles TSC warp between CPUs, turning off TSC clock.
[ 0.524000] Marking TSC unstable due to: check_tsc_sync_source failed.
[ 0.528000] Brought up 2 CPUs
[ 0.620000] migration_cost=4000
[ 0.620000] Booting paravirtualized kernel on bare hardware
[ 0.620000] Time: 12:01:09 Date: 01/23/108
[ 0.620000] NET: Registered protocol family 16
[ 0.620000] EISA bus registered
[ 0.620000] ACPI: bus type pci registered
[ 0.620000] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2
[ 0.620000] PCI: Using configuration type 1
[ 0.620000] Setting up standard PCI resources
[ 0.632000] ACPI: EC: Look up EC in DSDT
[ 0.640000] ACPI: Interpreter enabled
[ 0.640000] ACPI: (supports S0 S1 S3 S4 S5)
[ 0.640000] ACPI: Using IOAPIC for interrupt routing
[ 0.648000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.648000] PCI: Probing PCI hardware (bus 00)
[ 0.652000] PCI: Transparent bridge - 0000:00:14.4
[ 0.652000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.652000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.652000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[ 0.656000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.656000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.656000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.656000] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.656000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.656000] ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled.
[ 0.660000] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.660000] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[ 0.660000] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.660000] pnp: PnP ACPI init
[ 0.660000] ACPI: bus type pnp registered
[ 0.664000] pnp: PnP ACPI: found 13 devices
[ 0.664000] ACPI: ACPI bus type pnp unregistered
[ 0.664000] PnPBIOS: Disabled by ACPI PNP
[ 0.664000] PCI: Using ACPI for IRQ routing
[ 0.664000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.664000] PCI: Cannot allocate resource region 3 of device 0000:00:00.0
[ 0.676000] NET: Registered protocol family 8
[ 0.676000] NET: Registered protocol family 20
[ 0.676000] pnp: 00:07: iomem range 0xfff80000-0xffffffff could not be reserved
[ 0.676000] pnp: 00:09: ioport range 0xa00-0xa0f has been reserved
[ 0.676000] pnp: 00:09: ioport range 0xa10-0xa1f has been reserved
[ 0.676000] pnp: 00:09: ioport range 0xa20-0xa2f has been reserved
[ 0.676000] pnp: 00:09: ioport range 0xa30-0xa3f has been reserved
[ 0.676000] pnp: 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
[ 0.676000] pnp: 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 0.676000] pnp: 00:0b: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.676000] pnp: 00:0c: iomem range 0x0-0x9ffff could not be reserved
[ 0.676000] pnp: 00:0c: iomem range 0xc0000-0xcffff could not be reserved
[ 0.676000] pnp: 00:0c: iomem range 0xe0000-0xfffff could not be reserved
[ 0.676000] pnp: 00:0c: iomem range 0x100000-0x3bffffff could not be reserved
[ 0.708000] PCI: Bridge: 0000:00:01.0
[ 0.708000] IO window: d000-dfff
[ 0.708000] MEM window: fea00000-feafffff
[ 0.708000] PREFETCH window: d0000000-dfffffff
[ 0.708000] PCI: Bridge: 0000:00:14.4
[ 0.708000] IO window: e000-efff
[ 0.708000] MEM window: feb00000-febfffff
[ 0.708000] PREFETCH window: fdf00000-fdffffff
[ 0.708000] NET: Registered protocol family 2
[ 0.712000] Time: acpi_pm clocksource has been installed.
[ 0.712000] Switched to high resolution mode on CPU 0
[ 0.712000] Switched to high resolution mode on CPU 1
[ 0.756000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.756000] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[ 0.756000] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.756000] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.756000] TCP reno registered
[ 0.772000] checking if image is initramfs... it is
[ 1.344000] Freeing initrd memory: 7331k freed
[ 1.344000] audit: initializing netlink socket (disabled)
[ 1.344000] audit(1203768069.212:1): initialized
[ 1.344000] highmem bounce pool size: 64 pages
[ 1.348000] VFS: Disk quotas dquot_6.5.1
[ 1.348000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.348000] io scheduler noop registered
[ 1.348000] io scheduler anticipatory registered
[ 1.348000] io scheduler deadline registered
[ 1.348000] io scheduler cfq registered (default)
[ 1.348000] PCI: MSI quirk detected. MSI deactivated.
[ 1.400000] Boot video device is 0000:01:05.0
[ 1.400000] isapnp: Scanning for PnP cards...
[ 1.752000] isapnp: No Plug & Play device found
[ 1.780000] Real Time Clock Driver v1.12ac
[ 1.780000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 1.780000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 1.780000] input: Macintosh mouse button emulation as /class/input/input0
[ 1.780000] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 1.780000] PNP: PS/2 controller doesn't have AUX irq; using default 12
[ 1.784000] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.784000] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.784000] mice: PS/2 mouse device common for all mice
[ 1.784000] EISA: Probing bus 0 at eisa.0
[ 1.784000] Cannot allocate resource for EISA slot 2
[ 1.784000] Cannot allocate resource for EISA slot 3
[ 1.784000] Cannot allocate resource for EISA slot 4
[ 1.784000] Cannot allocate resource for EISA slot 5
[ 1.784000] Cannot allocate resource for EISA slot 6
[ 1.784000] Cannot allocate resource for EISA slot 7
[ 1.784000] Cannot allocate resource for EISA slot 8
[ 1.784000] EISA: Detected 0 cards.
[ 1.784000] TCP cubic registered
[ 1.784000] NET: Registered protocol family 1
[ 1.784000] Using IPI No-Shortcut mode
[ 1.784000] Magic number: 12:934:26
[ 1.784000] Freeing unused kernel memory: 364k freed
[ 1.816000] input: AT Translated Set 2 keyboard as /class/input/input1
[ 2.996000] AppArmor: AppArmor initialized<5>audit(1203768070.712:2): type=1505 info="AppArmor initialized" pid=1211
[ 3.004000] fuse init (API version 7.8)
[ 3.012000] Failure registering capabilities with primary security module.
[ 3.048000] ACPI: duty_cycle spans bit 4
[ 3.192000] ACPI Warning (tbutils-0217): Incorrect checksum in table [ ð] - 00, should be 6C [20070126]
[ 3.192000] ACPI Error (tbinstal-0134): Table has invalid signature [ ð], must be SSDT, PSDT or OEMx [20070126]
[ 3.192000] ACPI Error (psparse-0551): Method parse/execution failed [\_PR_.CPU1._PDC] (Node df815150), AE_BAD_SIGNATURE
[ 3.192000] ACPI: duty_cycle spans bit 4
[ 3.336000] ACPI Warning (tbutils-0217): Incorrect checksum in table [ ð] - 00, should be 6C [20070126]
[ 3.336000] ACPI Error (tbinstal-0134): Table has invalid signature [ ð], must be SSDT, PSDT or OEMx [20070126]
[ 3.336000] ACPI Error (psparse-0551): Method parse/execution failed [\_PR_.CPU2._PDC] (Node df8151e0), AE_BAD_SIGNATURE
[ 3.336000] ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 3.336000] ACPI Exception (processor_core-0783): AE_NOT_FOUND, Processor Device is not present [20070126]
[ 3.876000] usbcore: registered new interface driver usbfs
[ 3.876000] usbcore: registered new interface driver hub
[ 3.876000] usbcore: registered new device driver usb
[ 3.876000] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.876000] ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 16
[ 3.876000] ohci_hcd 0000:00:13.0: OHCI Host Controller
[ 3.876000] ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
[ 3.876000] ohci_hcd 0000:00:13.0: irq 16, io mem 0xfe9fe000
[ 3.940000] usb usb1: configuration #1 chosen from 1 choice
[ 3.940000] hub 1-0:1.0: USB hub found
[ 3.940000] hub 1-0:1.0: 4 ports detected
[ 4.000000] SCSI subsystem initialized
[ 4.040000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 4.040000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 4.044000] ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 16
[ 4.044000] ehci_hcd 0000:00:13.2: EHCI Host Controller
[ 4.044000] ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 2
[ 4.044000] ehci_hcd 0000:00:13.2: irq 16, io mem 0xfe9fc000
[ 4.044000] ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 4.044000] usb usb2: configuration #1 chosen from 1 choice
[ 4.044000] hub 2-0:1.0: USB hub found
[ 4.044000] hub 2-0:1.0: 8 ports detected
[ 4.048000] libata version 2.21 loaded.
[ 4.088000] FDC 0 is a post-1991 82077
[ 4.120000] 8139too Fast Ethernet driver 0.9.28
[ 4.148000] ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 16
[ 4.148000] ohci_hcd 0000:00:13.1: OHCI Host Controller
[ 4.148000] ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
[ 4.148000] ohci_hcd 0000:00:13.1: irq 16, io mem 0xfe9fd000
[ 4.208000] usb usb3: configuration #1 chosen from 1 choice
[ 4.208000] hub 3-0:1.0: USB hub found
[ 4.208000] hub 3-0:1.0: 4 ports detected
[ 4.312000] ATIIXP: IDE controller at PCI slot 0000:00:14.1
[ 4.312000] ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17
[ 4.312000] ATIIXP: chipset revision 128
[ 4.312000] ATIIXP: not 100% native mode: will probe irqs later
[ 4.312000] ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:pio, hdb:DMA
[ 4.312000] ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:DMA
[ 4.312000] Probing IDE interface ide0...
[ 4.824000] hdb: Maxtor 6Y160L0, ATA DISK drive
[ 4.880000] hdb: host side 80-wire cable detection failed, limiting max speed to UDMA33
[ 4.880000] hdb: selected mode 0x42
[ 4.880000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 4.880000] Probing IDE interface ide1...
[ 5.228000] usb 3-2: new full speed USB device using ohci_hcd and address 2
[ 5.436000] usb 3-2: configuration #1 chosen from 1 choice
[ 5.628000] hdc: LITE-ON DVDRW SHW-160H6S, ATAPI CD/DVD-ROM drive
[ 5.744000] usb 3-4: new full speed USB device using ohci_hcd and address 3
[ 5.952000] usb 3-4: configuration #1 chosen from 1 choice
[ 6.260000] usb 1-1: new full speed USB device using ohci_hcd and address 2
[ 6.416000] hdd: IDE-DVD DROM6216, ATAPI CD/DVD-ROM drive
[ 6.472000] hdc: host side 80-wire cable detection failed, limiting max speed to UDMA33
[ 6.472000] hdc: selected mode 0x42
[ 6.472000] hdd: host side 80-wire cable detection failed, limiting max speed to UDMA33
[ 6.472000] hdd: selected mode 0x42
[ 6.472000] ide1 at 0x170-0x177,0x376 on irq 15
[ 6.480000] usb 1-1: configuration #1 chosen from 1 choice
[ 6.488000] usbcore: registered new interface driver libusual
[ 6.500000] sata_sil 0000:00:11.0: version 2.2
[ 6.500000] ACPI: PCI Interrupt 0000:00:11.0[A] -> GSI 23 (level, low) -> IRQ 18
[ 6.500000] scsi0 : sata_sil
[ 6.500000] scsi1 : sata_sil
[ 6.500000] ata1: SATA max UDMA/100 cmd 0xf8864080 ctl 0xf886408a bmdma 0xf8864000 irq 18
[ 6.500000] ata2: SATA max UDMA/100 cmd 0xf88640c0 ctl 0xf88640ca bmdma 0xf8864008 irq 18
[ 6.504000] Initializing USB Mass Storage driver...
[ 6.504000] scsi2 : SCSI emulation for USB Mass Storage devices
[ 6.504000] usb-storage: device found at 3
[ 6.504000] usb-storage: waiting for device to settle before scanning
[ 6.504000] usbcore: registered new interface driver usb-storage
[ 6.504000] USB Mass Storage support registered.
[ 6.516000] usbcore: registered new interface driver hiddev
[ 6.524000] input: Logitech USB Gaming Mouse as /class/input/input2
[ 6.524000] input: USB HID v1.11 Mouse [Logitech USB Gaming Mouse] on usb-0000:00:13.0-1
[ 6.536000] hiddev96: USB HID v1.11 Device [Logitech USB Gaming Mouse] on usb-0000:00:13.0-1
[ 6.536000] usbcore: registered new interface driver usbhid
[ 6.536000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 6.812000] ata1: SATA link down (SStatus 0 SControl 310)
[ 7.140000] ata2: SATA link down (SStatus 0 SControl 310)
[ 7.140000] ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 19
[ 7.140000] scsi3 : sata_sil
[ 7.140000] scsi4 : sata_sil
[ 7.140000] ata3: SATA max UDMA/100 cmd 0xf8876880 ctl 0xf887688a bmdma 0xf8876800 irq 19
[ 7.140000] ata4: SATA max UDMA/100 cmd 0xf88768c0 ctl 0xf88768ca bmdma 0xf8876808 irq 19
[ 7.608000] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 7.616000] ata3.00: ATA-7: WDC WD3200JS-60PDB0, 21.00M21, max UDMA/100
[ 7.616000] ata3.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 0/1)
[ 7.632000] ata3.00: configured for UDMA/100
[ 7.944000] ata4: SATA link down (SStatus 0 SControl 310)
[ 7.944000] scsi 3:0:0:0: Direct-Access ATA WDC WD3200JS-60P 21.0 PQ: 0 ANSI: 5
[ 7.944000] ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 7.944000] eth0: RealTek RTL8139 at 0xf8840c00, 00:16:ec:34:0f:f9, IRQ 20
[ 7.944000] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 7.944000] ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 23 (level, low) -> IRQ 18
[ 7.996000] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
[ 8.000000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[febff000-febff7ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 8.028000] sd 3:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[ 8.028000] sd 3:0:0:0: [sda] Write Protect is off
[ 8.028000] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 8.028000] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.028000] sd 3:0:0:0: [sda] 625142448 512-byte hardware sectors (320073 MB)
[ 8.028000] sd 3:0:0:0: [sda] Write Protect is off
[ 8.028000] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 8.028000] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 8.028000] sda:<6>hdb: max request size: 512KiB
[ 8.028000] hdb: 320173056 sectors (163928 MB) w/2048KiB Cache, CHS=19929/255/63, UDMA(33)
[ 8.028000] hdb: cache flushes supported
[ 8.028000] hdb: hdb2
[ 8.040000] hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 8.040000] Uniform CD-ROM driver Revision: 3.20
[ 8.044000] hdd: ATAPI 40X DVD-ROM drive, 512kB Cache, UDMA(33)
[ 8.052000] sda1 sda2 sda3 < sda5 >
[ 8.064000] sd 3:0:0:0: [sda] Attached SCSI disk
[ 8.072000] sd 3:0:0:0: Attached scsi generic sg0 type 0
[ 8.412000] Attempting manual resume
[ 8.412000] swsusp: Resume From Partition 8:5
[ 8.412000] PM: Checking swsusp image.
[ 8.412000] PM: Resume from disk failed.
[ 8.444000] kjournald starting. Commit interval 5 seconds
[ 8.444000] EXT3-fs: mounted filesystem with ordered data mode.
[ 9.276000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[00000ae6ff4afe7b]
[ 11.508000] usb-storage: device scan complete
[ 11.512000] scsi 2:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0
[ 11.520000] scsi 2:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0
[ 11.524000] scsi 2:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0
[ 11.532000] scsi 2:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0
[ 11.540000] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 11.540000] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 11.552000] sd 2:0:0:1: [sdc] Attached SCSI removable disk
[ 11.552000] sd 2:0:0:1: Attached scsi generic sg2 type 0
[ 11.560000] sd 2:0:0:2: [sdd] Attached SCSI removable disk
[ 11.560000] sd 2:0:0:2: Attached scsi generic sg3 type 0
[ 11.572000] sd 2:0:0:3: [sde] Attached SCSI removable disk
[ 11.572000] sd 2:0:0:3: Attached scsi generic sg4 type 0
[ 15.968000] parport_pc 00:06: reported by Plug and Play ACPI
[ 15.968000] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 16.036000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04F9 pid 0x010F
[ 16.036000] usbcore: registered new interface driver usblp
[ 16.036000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 16.084000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 16.116000] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
[ 16.200000] Linux agpgart interface v0.102 (c) Dave Jones
[ 16.208000] input: PC Speaker as /class/input/input3
[ 16.296000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 16.444000] Linux video capture interface: v2.00
[ 16.524000] bttv: driver version 0.9.17 loaded
[ 16.524000] bttv: using 8 buffers with 2080k (520 pages) each for capture
[ 16.524000] bttv: Bt8xx card found (0).
[ 16.524000] ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 16.524000] bttv0: Bt878 (rev 17) at 0000:02:01.0, irq: 21, latency: 64, mmio: 0xfdfff000
[ 16.524000] bttv0: detected: ATI TV Wonder/VE [card=64], PCI subsystem ID is 1002:0003
[ 16.524000] bttv0: using: ATI TV-Wonder VE [card=64,autodetected]
[ 16.524000] bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init]
[ 16.524000] bttv0: using tuner=19
[ 16.524000] bttv0: i2c: checking for TDA9875 @ 0xb0... <6>usbcore: registered new interface driver xpad
[ 16.656000] /build/buildd/linux-source-2.6.22-2.6.22/drivers/input/joystick/xpad.c: driver for Xbox controllers v0.1.6
[ 16.716000] not found
[ 16.716000] bttv0: i2c: checking for TDA7432 @ 0x8a... not found
[ 16.764000] bttv0: i2c: checking for TDA9887 @ 0x86... not found
[ 16.800000] tuner 1-0060: All bytes are equal. It is not a TEA5767
[ 16.800000] tuner 1-0060: chip found @ 0xc0 (bt878 #0 [sw])
[ 16.800000] tuner 1-0060: type set to 19 (Temic PAL* auto (4006 FN5))
[ 16.800000] tuner 1-0060: type set to 19 (Temic PAL* auto (4006 FN5))
[ 16.816000] bttv0: registered device video0
[ 16.816000] bttv0: registered device vbi0
[ 16.816000] bttv0: PLL: 28636363 => 35468950 .. ok
[ 16.936000] bt878: AUDIO driver version 0.0.0 loaded
[ 16.936000] bt878: Bt878 AUDIO function found (0).
[ 16.936000] ACPI: PCI Interrupt 0000:02:01.1[A] -> GSI 21 (level, low) -> IRQ 21
[ 16.936000] bt878_probe: card id=[0x31002], Unknown card.
[ 16.936000] Exiting..
[ 16.936000] ACPI: PCI interrupt for device 0000:02:01.1 disabled
[ 16.936000] bt878: probe of 0000:02:01.1 failed with error -22
[ 16.956000] ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 17
[ 17.192000] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[ 17.672000] lp0: using parport0 (interrupt-driven).
[ 17.852000] Adding 5791392k swap on /dev/sda5. Priority:-1 extents:1 across:5791392k
[ 18.216000] EXT3 FS on sda2, internal journal
[ 23.052000] input: Power Button (FF) as /class/input/input4
[ 23.052000] ACPI: Power Button (FF) [PWRF]
[ 23.052000] input: Power Button (CM) as /class/input/input5
[ 23.052000] ACPI: Power Button (CM) [PWRB]
[ 23.160000] No dock devices found.
[ 24.820000] eth0: link down
[ 24.968000] ppdev: user-space parallel port driver
[ 25.436000] audit(1203793293.678:3): type=1503 operation="inode_permission" requested_mask="a" denied_mask="a" name="/dev/tty" pid=5270 profile="/usr/sbin/cupsd"
[ 25.680000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 25.680000] apm: disabled - APM is not SMP safe.
[ 26.532000] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[ 26.532000] [fglrx] Maximum main memory to use for locked dma buffers: 866 MBytes.
[ 26.536000] [fglrx] module loaded - fglrx 8.37.6 [May 25 2007] on minor 0
[ 26.620000] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level, low) -> IRQ 22
[ 27.180000] Failure registering capabilities with primary security module.
[ 27.368000] [fglrx] total GART = 130023424
[ 27.368000] [fglrx] free GART = 114032640
[ 27.368000] [fglrx] max single GART = 114032640
[ 27.368000] [fglrx] total LFB = 67108864
[ 27.368000] [fglrx] free LFB = 40062976
[ 27.368000] [fglrx] max single LFB = 40062976
[ 27.368000] [fglrx] total Inv = 0
[ 27.368000] [fglrx] free Inv = 0
[ 27.368000] [fglrx] max single Inv = 0
[ 27.368000] [fglrx] total TIM = 0
[ 27.480000] Bluetooth: Core ver 2.11
[ 27.480000] NET: Registered protocol family 31
[ 27.480000] Bluetooth: HCI device and connection manager initialized
[ 27.480000] Bluetooth: HCI socket layer initialized
[ 27.524000] Bluetooth: L2CAP ver 2.8
[ 27.524000] Bluetooth: L2CAP socket layer initialized
[ 27.548000] Bluetooth: RFCOMM socket layer initialized
[ 27.548000] Bluetooth: RFCOMM TTY layer initialized
[ 27.548000] Bluetooth: RFCOMM ver 1.8
[ 1506.752000] hda-intel: Invalid position buffer, using LPIB read method instead.
