BY, Would you please relate whether the modem succeeds in a simple dialout using wvdial, as we have not yet had a firm evaluation in dialout mode with the > > NAME="Modem: SILICON Laboratories > > PCIDEV=1543:3052 > > SUBSYS=1543:3000 chipset. Jacques is much more knowledgeable than I on server applications and may be able to help you further. MarvS On Feb 19, 2008 3:15 PM, B. Younes <behloul.maliste@xxxxxxxxx> wrote: > Hi Marvin, > > Thank you for the recommandations. I've followed them but the problem > is still here. > > I wan't to use my linmodem as a dial-in server, to remotly connect to > the server. > > I still have the problem when trying to dial (even with wvdial) or > answer a call with the AT Hayes command "ATA", the modem doesn't log > any message when recieving a call, and when I send the command "ATA" > to the modem, it hangs !! > The modem answer al these commands: > > > #minicom > AT S7=45 S0=0 L1 V1 X4 &c1 E1 Q0 > OK > ATI > SmartLink Soft Modem > OK > ATI2 > SmartLink Soft Modem, 2.9.11 > Smart Link Ltd. > OK > ATI3 > /dev/slamr0 > modemap driver > OK > ATI4 > s00=000 s01=000 s02=043 s03=013 s04=010 s05=008 s06=002 s07=045 > s08=002 s09=006 s10=007 s11=100 s12=050 s13=001 s14=000 s15=001 > s16=001 s17=000 s18=000 s19=000 s20=000 s21=000 s22=000 s23=000 > > OK > ATI5 > Stored Profile 0: > OK > ATI6 > Stored Profile 1: > OK > ATI7 > Country: ALGERIA > OK > ATI8 > ERROR > > ATD 050024222 > (HANG) > > > Hope this helps to clarify the problem. > > > On Feb 19, 2008 3:07 PM, Marvin Stodolsky <marvin.stodolsky@xxxxxxxxx> wrote: > > BY > > > > For > > > > CLASS="Class 0703: 1543:3052" > > NAME="Modem: SILICON Laboratories Intel 537 [Winmodem] " > > PCIDEV=1543:3052 > > SUBSYS=1543:3000 > > SUBven=1543 > > IRQ=7 > > IDENT=INTEL537_on_1543:3052 > > > > Support through the slamr driver is CORRECT to try, but support is > > provisional with your > > ---- > > root@ankara:/usr/src/slmodem-2.9.11-20080126/modem# ./slmodemd -c > > ALGERIA /dev/slamr0 > > SmartLink Soft Modem: version 2.9.11 Feb 19 2008 12:18:12 > > symbolic link `/dev/ttySL0' -> `/dev/pts/4' created. > > modem `slamr0' created. TTY is `/dev/pts/4' > > ---- > > GOOD starting news. > > Try to improve the System through the following steps: > > 1) Complete uninstall any hsfmodem software: > > # hsfconfig --uninstall > > as it may be competing for resources > > 2) The sl-modem-daemon package installed an older version 2.9.9 > > slmodemd, which cannot serve. So > > # mv /usr/sbin/slmodemd /usr/sbin/slmodemd.2.9.9. > > # cp -a /usr/src/slmodem-2.9.11-20080126/modem/slmodemd /usr/sbin/slmodemd > > Then > > # slmodemd --version > > should report 2.9.11 > > > > Replace the default USA with ALGERIA through > > # sudo gedit /etc/default/sl-modem-daemon > > Reboot. The sl-modem-daemon should now do the modem activation > > automatically through > > the step: > > # slmodemd -c ALGERIA /dev/slamr0 > > > > Minicom is not an ideal testing tool for softmodems. See in the modem > > is found through > > # wvdialconf /etc/wvdial.conf > > Edit in your dialout info with > > # sudo gedit /etc/wvdial.conf > > adding the line > > Carrier Check = no > > and removing the symbols ; < > > > > > Save. > > Try a dialout with > > # wvdial. > > > > Please report back!!! > > > > MarvS > > scanModem maintainer > > > > > > > > On Feb 19, 2008 7:05 AM, B. Younes <behloul.maliste@xxxxxxxxx> wrote: > > > subsubject "Linmodem, Intex chipset Silicon Labs, driver slmodem can't > > > answer "ATA"" > > > > > > Hello, > > > > > > I've read and followed Linmodem Howto. it helped me to find the > > > correct Linux driver, but I still have a small problem: > > > It's about a PCI Modem card, made by Intex (China), I downloaded a > > > installed the last slmodem > > > > > > 1) Loading slmodem driver > > > (slmodem-2.9.11-20080126), the driver regognise the Modem and print this (dmesg) > > > ----------- start dmesg log ---- > > > slamr: SmartLink AMRMO modem. > > > slamr: probe 1543:3052 SL2800 card... > > > ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKE] -> GSI 7 (level, > > > low) -> IRQ 7 > > > slamr: amrmo_pci_probe: 0 amrmo is c3fe0000. data d3328a40, io a000, 0. > > > slamr: slamr0 is SL2800 card. > > > ------------ end dmesg log ----- > > > > > > 2) starting slmodemd deamon > > > root@ankara:/usr/src/slmodem-2.9.11-20080126/modem# ./slmodemd -c > > > ALGERIA /dev/slamr0 > > > SmartLink Soft Modem: version 2.9.11 Feb 19 2008 12:18:12 > > > symbolic link `/dev/ttySL0' -> `/dev/pts/4' created. > > > modem `slamr0' created. TTY is `/dev/pts/4' > > > Use `/dev/ttySL0' as modem device, Ctrl+C for termination. > > > > > > 3) starting minicom > > > AT S7=45 S0=0 L1 V1 X4 &c1 E1 Q0 > > > OK > > > at > > > OK > > > ath1 > > > OK > > > ath0 > > > OK > > > ata > > > (HUNG !!!) > > > > > > I've also loaded the driver in debug mode, no message is logged when a > > > dial-in call arrives. > > > > > > Next is the ModemData.txt: > > > > > > Thanks in advance. > > > ############ START MODEMDATA.TXT ########### > > > Only plain text email is forwarded by the Discuss@xxxxxxxxxxxxx List Server, > > > as HTML can contain viruses. Use as the email Subject Line: > > > YourName, YourCountry Debian GNU/Linux 4.0 kernel 2.6.22.15 > > > With this Subject Line cogent experts will be alerted, and useful > > > case names left in the Archive. > > > YourCountry will enable Country specific guidance. Your contry's > > > local Linux experts > > > can be found through: http://www.linux.org/groups/index.html. > > > They will know your Country's modem code, which may be essential for > > > dialup service. > > > Responses from Discuss@xxxxxxxxxxxxx are sometimes blocked by an > > > Internet Provider mail filters. > > > So in a day, also check the Archived responses at http://www.linmodems.org > > > -------------------------- System information ---------------------------- > > > CPU=i686, Debian GNU/Linux 4.0 > > > Linux version 2.6.22.15 (root@ankara) (gcc version 3.4.6 (Debian > > > 3.4.6-5)) #3 Wed Feb 13 09:15:32 CET 2008 > > > scanModem update of: 2008_02_10 > > > The modem symbolic link is /dev/modem -> ttySL0 > > > > > > There are no blacklisted modem drivers in /etc/modprobe* files > > > PCI slot 00:1b.0 has a High Definition Audio Card > > > > > > The Advanced Linux Sound Architecture (ALSA) packages providing audio support, > > > also includes drivers for some modems. The ALSA diagnostics are written during > > > bootup to /proc/asound/ folders. > > > > > > USB modem not detected by lsusb > > > For candidate card in slot 01:00.0, firmware information and bootup > > > diagnostics are: > > > PCI slot PCI ID SubsystemID Name > > > ---------- --------- --------- -------------- > > > 01:00.0 1543:3052 1543:3000 Modem: SILICON Laboratories Intel 537 [Winmodem] > > > > > > Modem interrupt assignment and sharing: > > > --- Bootup diagnostics for card in PCI slot 01:00.0 ---- > > > ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKE] -> GSI 7 (level, > > > low) -> IRQ 7 > > > Couldn't register serial port 0000:01:00.0: -28 > > > > > > For candidate card in slot 00:1b.0, firmware information and bootup > > > diagnostics are: > > > PCI slot PCI ID SubsystemID Name > > > ---------- --------- --------- -------------- > > > 00:1b.0 8086:27d8 1458:a002 Audio device: Intel Corporation 82801G > > > > > > Modem interrupt assignment and sharing: > > > 5: 0 XT-PIC-XT uhci_hcd:usb5 > > > --- Bootup diagnostics for card in PCI slot 00:1b.0 ---- > > > > > > > > > === Finished modem firmware and bootup diagnostics section. === > > > === Next deducing cogent software === > > > > > > > > > > > > > > > Predictive diagnostics for card in PCI bus 01:00.0: > > > Modem chipset not detected on > > > CLASS="Class 0703: 1543:3052" > > > NAME="Modem: SILICON Laboratories Intel 537 [Winmodem] " > > > PCIDEV=1543:3052 > > > SUBSYS=1543:3000 > > > SUBven=1543 > > > IRQ=7 > > > IDENT=INTEL537_on_1543:3052 > > > > > > For candidate modem in PCI bus: 01:00.0 > > > Class 0703: 1543:3052 Modem: SILICON Laboratories Intel 537 [Winmodem] > > > Primary PCI_id 1543:3052 > > > Support type needed or chipset: INTEL537_on_1543:3052 > > > > > > > > > ----------------end Softmodem section -------------- > > > > > > > > > Predictive diagnostics for card in PCI bus 00:1b.0: > > > Modem chipset not detected on > > > CLASS="Class 0403: 8086:27d8" > > > NAME="Audio device: Intel Corporation 82801G " > > > PCIDEV=8086:27d8 > > > SUBSYS=1458:a002 > > > SUBven=1458 > > > IRQ=5 > > > HDA=8086:27d8 > > > SOFT=8086:27d8.HDA > > > > > > > > > High Definition Audio (HDA) cards MAY host a modem chip in their Subsystem, > > > and many are supported by the ALSA audio+modem driver snd-hda-intel > > > A modem was not detected on HDA card 8086:27d8. > > > If another modem card is present, then most likely 8086:27d8 does not > > > host a modem. > > > If another modem card has not been detected, then possibilities are: > > > 1) A Conexant modem chip is present on 8086:27d8, as Conexant chips > > > are frequently not detectable by ALSA diagnostics > > > 2) The modem may be of the older non-PCI Controller Chipset (hardware) type. > > > Try detection with Root permission: > > > wvdialconf /etc/wvdial.conf > > > > > > For candidate modem in PCI bus: 00:1b.0 > > > Class 0403: 8086:27d8 Audio device: Intel Corporation 82801G > > > Primary PCI_id 8086:27d8 > > > Subsystem PCI_id 1458:a002 > > > Softmodem codec or chipset from diagnostics: > > > from Archives: > > > > > > > > > > > > Lacking a dsp (digital signal processing) chip, the modem is a software > > > intensive or "softmodem" type. Its primary controller manages the traffic > > > with the CPU. But the software needed is specified in the Subsystem. > > > ----------------------------------------- > > > Support type needed or chipset: > > > > > > Support can likely be achieved through two mutually exclusive alternatives: > > > 1) The hsfmodem software for Conexant chipset modems: Read Conexant.txt > > > The following ALSA alternative CANNOT work with Conexant modems. > > > > > > 2) An ALSA modem driver plus slmodemd. Read Smartlink.txt for details, and > > > to test get the package SLMODEMD.gcc3.4.tar.gz from: > > > http://linmodems.technion.ac.il/packages/smartlink/ > > > > > > ----------------end Softmodem section -------------- > > > > > > Completed candidate modem analyses. > > > > > > The base of the UDEV device file system is: /dev/.udev > > > > > > Versions adequately match for the compiler installed: 3.4.6 > > > and the compiler used in kernel assembly: 3.4.6 > > > > > > > > > > > > Minimal compiling resources appear complete: > > > make utility - /usr/bin/make > > > Compiler version 3.4 > > > linuc_headers base folder /lib/modules/2.6.22.15/build > > > > > > However some compilations and executable functions may need additional files, > > > in the FileNames.h (so called kernel "h"eaders) collection installed > > > in /usr/include/ . > > > For martian_modem, additional required packages are libc6-dev (and > > > for Debian/Ubuntu, linux-libc-dev). The also required headers of > > > package libc6 are commonly installed by default. > > > > > > Compressed files at: /usr/src/linux-2.6.20.4.tar.bz2 > > > /usr/src/sl-modem.tar.bz2 /usr/src/squashfs.tar.bz2 > > > > > > For Debian and some related distributions, a package > > > kernel-kbuild-2.6-22 may be needed to support driver compiling > > > > > > > > > If a driver compilation fails, with message including some lack of > > > some FileName.h (stdio.h for example), then > > > Some additional kernel-header files need installation to /usr/include. > > > The minimal additional packages are libc6-dev > > > and any of its dependents, under Ubuntu linux-libc-dev > > > > > > If an alternate ethernet connection is available, > > > $ apt-get update > > > $ apt-get -s install linux-kernel-devel > > > will install needed package > > > For Debian/Ubuntu related distributions, run the following command to > > > display the needed package list: > > > > > > Otherwise packages have to be found through http://packages.ubuntu.com > > > Once downloaded and transferred into a Linux partition, > > > they can be installed alltogether with: > > > $ sudo dpkg -i *.deb > > > > > > > > > Checking pppd properties: > > > -rwsr-xr-- 1 root dip 265880 2006-06-04 04:58 /usr/sbin/pppd > > > > > > In case of an "error 17" "serial loopback" problem, see: > > > http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html > > > > > > To enable dialout without Root permission do: > > > $ su - root (not for Ubuntu) > > > chmod a+x /usr/sbin/pppd > > > or under Ubuntu related Linuxes > > > chmod a+x /usr/sbin/pppd > > > > > > Checking settings of: /etc/ppp/options > > > asyncmap 0 > > > auth > > > crtscts > > > lock > > > hide-password > > > modem > > > proxyarp > > > lcp-echo-interval 30 > > > lcp-echo-failure 4 > > > noipx > > > > > > In case of a message like: > > > Warning: Could not modify /etc/ppp/pap-secrets: Permission denied > > > see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html > > > > > > Read Modem/YourSystem.txt concerning other COMM channels: eth0 > > > Which can interfere with Browser naviagation. > > > > > > Don't worry about the following, it is for the experts > > > should trouble shooting be necessary. > > > ========================================================== > > > > > > # start/stop the daemon when the USB modem is connected > > > KERNEL=="slusb[0-9]*", GROUP="dialout", RUN+="/etc/init.d/sl-modem-daemon" > > > Checking for modem support lines: > > > -------------------------------------- > > > /device/modem symbolic link: lrwxrwxrwx 1 root root 6 > > > 2008-02-19 11:43 /dev/modem -> ttySL0 > > > slmodemd created symbolic link /dev/ttySL0: > > > Within /etc/udev/ files: > > > /etc/udev/rules.d/030_sl-modem-daemon.rules:# start/stop the daemon > > > when the USB modem is connected > > > /etc/udev/rules.d/030_sl-modem-daemon.rules:KERNEL=="slusb[0-9]*", > > > GROUP="dialout", RUN+="/etc/init.d/sl-modem-daemon" > > > /etc/udev/sl-modem-daemon.rules:# start/stop the daemon when the USB > > > modem is connected > > > /etc/udev/sl-modem-daemon.rules:KERNEL=="slusb[0-9]*", > > > GROUP="dialout", RUN+="/etc/init.d/sl-modem-daemon" > > > Within /etc/modprobe.conf files: > > > /etc/modprobe.d/alsa-base:options snd-atiixp-modem index=-2 > > > /etc/modprobe.d/alsa-base:options snd-via82xx-modem index=-2 > > > /etc/modprobe.d/sl-modem-daemon.modutils:install slamr modprobe > > > --ignore-install ungrab-winmodem ; modprobe --ignore-install slamr; > > > test -e /dev/slamr0 || (/bin/mknod -m 660 /dev/slamr0 c 242 0 > > > 2>/dev/null && chgrp dialout /dev/slamr0) > > > /etc/modprobe.d/alsa-base-blacklist:# Uncomment these entries in order > > > to blacklist unwanted modem drivers > > > /etc/modprobe.d/alsa-base-blacklist:# blacklist snd-atiixp-modem > > > /etc/modprobe.d/alsa-base-blacklist:# blacklist snd-via82xx-modem > > > Within any ancient /etc/devfs files: > > > > > > Within ancient kernel 2.4.n /etc/module.conf files: > > > /etc/modules.conf:options snd-atiixp-modem index=-2 > > > /etc/modules.conf:options snd-via82xx-modem index=-2 > > > /etc/modules.conf:# Uncomment these entries in order to blacklist > > > unwanted modem drivers > > > /etc/modules.conf:# alias snd-atiixp-modem off > > > /etc/modules.conf:# alias snd-via82xx-modem off > > > /etc/modules.conf:### update-modules: start processing > > > /etc/modutils/sl-modem-daemon.modutils > > > /etc/modules.conf:### update-modules: end processing > > > /etc/modutils/sl-modem-daemon.modutils > > > /etc/modules.conf.old:options snd-atiixp-modem index=-2 > > > /etc/modules.conf.old:options snd-via82xx-modem index=-2 > > > /etc/modules.conf.old:# Uncomment these entries in order to blacklist > > > unwanted modem drivers > > > /etc/modules.conf.old:# alias snd-atiixp-modem off > > > /etc/modules.conf.old:# alias snd-via82xx-modem off > > > /etc/modules.conf.old:alias /dev/modem /dev/ttySHSF > > > /etc/modules.conf.old:### update-modules: start processing > > > /etc/modutils/sl-modem-daemon.modutils > > > /etc/modules.conf.old:### update-modules: end processing > > > /etc/modutils/sl-modem-daemon.modutils > > > --------- end modem support lines -------- > > > > > >
