Amos,
sudo lsmod | grep snd-intel
will show you that snd-intel8x0m is loaded and also which other
module(s) is/are using it.
If you first rmmod the one(s) which uses snd-intel8x0m, you will be able
to remove snd-intel8x0m
If you are not sure about what removing other modules can cause, send us
the file amos.txt created by command sudo lsmod > amos.txt
and we will advise you.
Jacques
amosse@xxxxxxxxx wrote:
Thank you.
I followed your instruction, I mean
1) stop wvdial (Ctrl+C)
2) stop slmodemd(Ctrl+C in its start control: #slmodemd -c ITALY --alsa modem:1)
3) stop snd-intel8x0m (#sudo modprobe -r snd-intel8x0m)
4) # ifconfig
eth0 Link encap:Ethernet HWaddr 00:0C:6E:BD:08:6E
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:11 Base address:0xa000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:205 errors:0 dropped:0 overruns:0 frame:0
TX packets:205 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:17591 (17.1 Kb) TX bytes:17591 (17.1 Kb)
# sudo ifconfig eth0 down
Problem remain still the same, I don't get to stop snd-intel8x0m, I get still same messagge:
FATAL:module snd_intel8x0m is in use
May problem is snd-intel8x0m driver?
Is there other solution?
Amos
RE:> FATAL: module snd_intel8x0m is in use
First stop wvdial, or whatever dialer your are using.
2nd stop slmodemd in its start console with:
Ctrl-C
ONLY then
$ sudo modprobe -r snd-intel8x0m
Also stop other COMM channels before trying a dialout
$ ifconfig
to display. If eth0 is show
$ sudo ifconfig eth0 down
The lo "loopback" should be retained.
MarvS
MarvS
On Dec 26, 2007 3:55 PM, amosse@xxxxxxxxx <amosse@xxxxxxxxx> wrote:
Thank you.
I tried with
$ sudo modprobe -r snd-intel8x0m
but I get:
FATAL: module snd_intel8x0m is in use
Amos
Amos,
When you get flaky behavior with the modem,
stop wvdial if necessary
stop slmodemd with
Ctrl-C
unload the driver
$ sudo modprobe -r snd-intel8x0m
reload the driver
$ sudo modprobe snd-intel8x0m
and retest the modem.
Our experience is that sometimes these drivers do lost function after
a while when loaded.
MarvS
On Dec 26, 2007 1:36 PM, amosse@xxxxxxxxx <amosse@xxxxxxxxx> wrote:
Many thanks for your reply.
I don't know why is not working at all, this is very strange...
Now problem is that after #wvdial I get
.............
ATDT7020187187
--> Timed out while dialing. Trying again.
--> Sending: ATDT7020187187
--> Waiting for carrier.
and so on without getting any connection
I start from wvdial.conf
[Dialer Defaults]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0 +MS=34
Modem Type = Analog Modem
Phone = 7020187187
ISDN = 0
Username = telecom
Password = telecom
Modem = /dev/ttySL0
Baud = 460800
#New PPPD = yes
Carrier Check = no
SetVolume = 1
Stupid mode = yes
Auto DNS = yes
#Dial Command = ATDT
[Dialer 2nd]
Username = amosse@xxxxxxxxx
Password = bomba
Phone = 0571861010
It semms to be OK?, only some questions:
Looking on the web I find some examples with Dial Command, is it important to put it? If yes what value?
In any case I tried both with and without no changes:
Yesterday during my succesfull trial sometimes I did't start
slmodemd in the normal way:
# slmodemd -c ITALY --alsa modem:1
because I have set up slmodemd in "Editor runlevel" on yes, in this way I think service start automatically, but I don't know if with alsa support...
I have to inizialize slmodemd service as above or leave it autoload with runlevel?
I try both providers same problem as above said.
This is very strange behaviour, what I have to check ...??
Thanks
Amos
ps: do you have some wvdial.conf tutorial to suggest me in order to understand meaning of the set up.
Amos,
Good progress!!
Note X3 is in Init2. For Init1 use
Init1 = ATZ
RE: is it right to set up wvdial.conf in this way in order to connect
to 2 different provider? (I try telecom connection dialing # wvdial
2nd)
--------
Yes, but you could simplify as, the "wvdial 2nd" will reference the
default, for any missing lines. So if would suffice to use format:
[Dialer default]
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0 +MS=90
# +MS=34 might provide a longer CONNECT
Modem Type = Analog Modem
Phone = 0571861010
ISDN = 0
Username = amosse@xxxxxxxxx
Password = zzzzzzzz
Modem = /dev/ttySL0
Baud = 460800
Carrier Check = no
SetVolume = 1
Stupid mode = yes
Auto DNS = yes
[Dialer 2nd]
Phone = 7020187187
Username = telecom
Password = telecom
Read Jacques Post Install HowTo at
On Dec 25, 2007 12:53 PM, amosse@xxxxxxxxx <amosse@xxxxxxxxx> wrote:
Got it!
This is a great result for me.
# slmodemd -c ITALY --alsa modem:1
SmartLink Soft Modem: version 2.9.11 Nov 21 2007 09:03:10
symbolic link `/dev/ttySL0' -> `/dev/pts/3' created.
modem `modem:1' created. TTY is `/dev/pts/3'
Use `/dev/ttySL0' as modem device, Ctrl+C for termination.
[Dialer 2nd]
Init2 = ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0 +MS=90
Modem Type = Analog Modem
Phone = 7020187187
ISDN = 0
Username = telecom
Init1 = ATX3
Password = telecom
Modem = /dev/ttySL0
Baud = 460800
Carrier Check = no
SetVolume = 1
Stupid mode = yes
Auto DNS = yes
wvdial 2nd
--> WvDial: Internet dialer version 1.56 (abuild@balli)
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATX3
ATX3
OK
--> Sending: ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0 +MS=90
ATQ0 V1 E1 S0=0 X3 &C1 &D2 +FCLASS=0 +MS=90
OK
--> Modem initialized.
--> Sending: ATX3DT7020187187
--> Waiting for carrier.
ATX3DT7020187187
CONNECT 53333
--> Carrier detected. Starting PPP immediately.
--> Starting pppd at Tue Dec 25 21:39:23 2007
--> Pid of pppd: 22386
--> Using interface ppp0
--> pppd: 8[11][06][08][18][10][06][08]
--> pppd: 8[11][06][08][18][10][06][08]
--> pppd: 8[11][06][08][18][10][06][08]
--> pppd: 8[11][06][08][18][10][06][08]
--> local IP address 80.104.165.49
--> pppd: 8[11][06][08][18][10][06][08]
--> remote IP address 151.99.26.43
--> pppd: 8[11][06][08][18][10][06][08]
--> primary DNS address 62.211.69.150
--> pppd: 8[11][06][08][18][10][06][08]
--> secondary DNS address 212.48.4.15
--> pppd: 8[11][06][08][18][10][06][08]
--> Script /etc/ppp/ip-up run successful
--> Default route Ok.
--> Nameserver (DNS) Ok.
--> Connected... Press Ctrl-C to disconnect
--> pppd: 8[11][06][08][18][10][06][08]
Many thanks to everybody
Amos
