Bob, I have been there, done that! Jacques has a page to help. Please read it carefully http://linmodems.technion.ac.il/post-install.html There you will find links to pages that can help you fix most issues. What does your ISP want? http://axion.physics.ubc.ca/ppp-linux.html If you are using Juno as your provider, then you are indeed having alot of trouble. http://ubuntuforums.org/archive/index.php/t-67980.html I have a friend that used Juno and it connected, but very slowly with linux. Even on Window$ it was a pain to get connected. You have to use their software to connect to their servers. What is your ISP? Maybe finding out what they want, will help you get connected to the net. maybe adding the nameservers to /etc/resolv.conf will fix your issues. Regards, Antonio On 11/13/07, Bob Terrell <bob_terrell_texas@xxxxxxxxx> wrote: > Marvin, > >>>>>>>>>>>>>>>>>>>> > RE: RE: START SLMODEMD > SmartLink Soft Modem: version 2.9.9e-pre1 Mar 20 2007 > -------- > 2.9.9e-pre1 is the version installed by the > sl-modem-deamon package. > > It should be replaced by the > $ slmodemd --version > SmartLink Soft Modem: version 2.9.11 > DONE > >>>>>>>>>>>>>>>>>>>> > RE: If you wish, you can edit > $ sudo gedit /etc/default/sl-modem-daemon > to > DONTSTART=1 > DONE, and I no longer have to reboot - Thank you. > >>>>>>>>>>>>>>>>>>>> > RE: RE: $ wvdial -C ./wvdial.juno > you need sudo: > $ sudo wvdial -C ./wvdial.juno > DONE > >>>>>>>>>>>>>>>>>>>> > Dialup now progresses further. Listings below are now > showing a lot of errors that say HDLC frame errors: > NOTE: these errors are different from one login to > another. May be due to not rebooting between runs. > <659.024505> slamr0: hdlc frame size error. > <661.389290> slamr0: hdlc frame integrity error. > <664.269130> slamr0: hdlc frame size error. > <664.269186> slamr0: hdlc frame fcs error. > Help desk at NTS says that it looked like I > successfully connected, for about a minute on each > account. I just repeated that again, same result on > the ISP side. > On my end I did not see anything that would allow me > to interact with the login. Do I need a terminal > window now, and how should I start that? > Incidentally, I just noticed slmodem.log.slamr0 in my > home directory. Should I send that to you? > >>>>>>>>>>>>>>>>>>>> > Thanks, > Bob Terrell > > > //////////////////////////////// > Listings below in order: > SCRIPT TO SHUT DOWN ETH0 AND START MODEM (only > slightly modified) > WVDIAL.BCOOPER IN PLACE OF /ETC/WVDIAL.CONF (using > acooper account) > LOG OF FIRST TERMINAL > LOG OF SECOND TERMINAL > >>>>>>>>>>>>>>>>>>>> > SECOND RUN WITH WVDIAL.BCOOPER (using bcooper1 > account) > >>>>>>>>>>>>>>>>>>>> > LOG OF FIRST TERMINAL > LOG OF SECOND TERMINAL > >>>>>>>>>>>>>>>>>>>> > > > > //////////////////////////////////// > SCRIPT TO SHUT DOWN ETH0 AND START MODEM (only > slightly modified) > #!/bin/bash > # startmodem - shut down eth0 and start modem - Bob > Terrell 11/11/07 > > #--------------------------------- > # shut down eth0 as e100 and release and restart slamr > echo SHUTTING DOWN eth0 > sudo ifconfig eth0 down > sudo modprobe -r e100 > echo TOGGLE SLAMR > sudo modprobe -r slamr > sudo modprobe slamr > > #--------------------------- > > # start slmodemd with debug and logging > echo SHUT DOWN sl-modem-daemon > sudo /etc/init.d/sl-modem-daemon stop > echo START SLMODEMD > echo AFTER IT SETTLES, START SUDO WVDIAL IN A SEPARATE > TERMINAL WINDOW > sudo slmodemd -c USA --log --debug=1 /dev/slamr0 > > /////////////////////////////////////// > WVDIAL.BCOOPER IN PLACE OF /ETC/WVDIAL.CONF (using > acooper account) > $ cat wvdial.bcooper > > [Dialer Defaults] > Init1 = ATZ > Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > Modem Type = Analog Modem > ISDN = 0 > New PPPD = yes > Phone = 6875000 > Modem = /dev/ttySL0 > Username = acooper > Carrier check = no > Password = Pirates1 > Baud = 460800 > $ > > > //////////////////////////////////// > LOG OF FIRST TERMINAL > $ sudo ./startmodem > SHUTTING DOWN eth0 > TOGGLE SLAMR > SHUT DOWN sl-modem-daemon > Shutting down SmartLink Modem driver normally ... no > slmodemd daemon running. > Unloading modem driver from kernel ... slamr. > START SLMODEMD > AFTER IT SETTLES, START SUDO WVDIAL IN A SEPARATE > TERMINAL WINDOW > SmartLink Soft Modem: version 2.9.11 May 26 2007 > 13:41:57 > <132.289609> SmartLink Soft Modem: version 2.9.11 May > 26 2007 13:41:57 > <132.290148> slamr0: startup modem... > <132.290359> slamr0: update termios... > symbolic link `/dev/ttySL0' -> `/dev/pts/2' created. > modem `slamr0' created. TTY is `/dev/pts/2' > <132.291452> open file: > /var/lib/slmodem/data.slamr0... > <132.311348> cannot open > '/var/lib/slmodem/data.slamr0': No such file or > directory > /////////// IS ERROR ABOVE A PROBLEM? > <132.745625> main: rt applyed: SCHED_FIFO, pri 99 > Use `/dev/ttySL0' as modem device, Ctrl+C for > termination. > /////////////START SECOND TERMINAL HERE > <167.209057> main: termios changed. > <167.209143> slamr0: update termios... > <167.284697> main: termios changed. > <167.284773> slamr0: update termios... > <167.384763> slamr0: run cmd: ATZ > <167.384843> slamr0: modem reset... > <167.384865> slamr0: modem set state: 1 --> 1... > <167.384888> slamr0: modem set mode: -> 0... > <167.384908> slamr0: modem report result: 0 (OK) > <167.484814> slamr0: run cmd: > ATQ0V1E1S0=0&C1&D2+FCLASS=0 > <167.484906> slamr0: modem set mode: -> 0... > <167.484928> slamr0: modem report result: 0 (OK) > <167.584907> slamr0: run cmd: ATDT6875000 > <167.584998> slamr0: modem dial: T6875000... > <167.585019> slamr0: modem_dial_start... > <167.585848> slamr0: modem_start.. > <167.585871> slamr0: modem set state: 1 --> 2... > <167.585893> slamr0: new state: DP_ESTAB > <167.585913> main: modemap_ioctl: cmd 8, arg 3... > <167.585943> slamr0: modem set hook: 0 --> 1... > <167.585964> main: modemap_ioctl: cmd 2, arg 1... > <167.585995> main: modemap_ioctl: cmd 11, arg 0... > <167.586098> main: modemap_ioctl: cmd 4, arg 2580... > <167.586123> main: modemap_ioctl: cmd 7, arg 30... > <167.586144> main: modemap_start... > <178.565850> slamr0: 105360: change dp: --> 8... > <181.420646> main: modemap_ioctl: cmd 10, arg 0... > <181.420715> slamr0: 132768: change dp: --> 90... > <181.424120> main: modemap_ioctl: cmd 10, arg 0... > <181.425534> main: change delay -48... > <181.430512> main: change delay -48... > <181.435515> main: change delay -4... > <183.325578> main: change delay +384... > <197.614478> slamr0: modem_update_status: 256 > <197.614511> slamr0: --> DP LINK > <197.614532> slamr0: modem set state: 2 --> 4... > <197.614553> slamr0: new state: EC_ESTAB > <197.674144> slamr0: detector start... > <197.829358> slamr0: rx pattern: 0xa2. > <197.829411> slamr0: rx pattern: 0xc2. > <197.834123> slamr0: detector finished. > <197.834151> slamr0: modem_update_status: 1024 > <197.834172> slamr0: --> PACK LINK > <197.834196> slamr0: hdlc_start... > <198.019309> slamr0: modem update config... > <198.019357> slamr0: ec = 1 (1) > <198.019378> slamr0: ec_detector = 1 (1) > <198.019399> slamr0: ec_tx_win_size = 15 (15) > <198.019420> slamr0: ec_rx_win_size = 15 (15) > <198.019440> slamr0: ec_tx_info_size = 128 (128) > <198.019461> slamr0: ec_rx_info_size = 128 (128) > <198.019482> slamr0: comp = 3 (3) > <198.019502> slamr0: comp_dict_size = 2048 (2048) > <198.019559> slamr0: comp_max_string = 32 (34) > <198.154342> slamr0: modem_update_status: 4096 > <198.154392> slamr0: --> EC LINK > <198.154413> slamr0: modem set state: 4 --> 5... > <198.154434> slamr0: new state: MODEM_ONLINE > <198.154455> slamr0: modem report result: 1 (CONNECT) > <198.154489> main: modemap_ioctl: cmd 8, arg 0... > <199.309226> slamr0: hdlc frame integrity error. > <203.648820> slamr0: hdlc frame size error. > <204.922039> main: termios changed. > <204.922094> slamr0: update termios... > <209.758329> slamr0: hdlc frame size error. > <219.757468> slamr0: hdlc frame size error. > <219.757504> slamr0: hdlc frame size error. > <250.634743> slamr0: modem_update_status: 8192 > <250.634791> slamr0: --> EC UNLINK > <250.634812> slamr0: modem_hup... > <250.634833> slamr0: modem set state: 5 --> 9... > <250.634855> slamr0: new state: DP_DISC > <250.634890> slamr0: modem_stop.. > <250.634910> main: modemap_stop... > <250.634964> slamr0: modem set hook: 1 --> 0... > <250.634986> main: modemap_ioctl: cmd 2, arg 0... > <250.635018> main: modemap_ioctl: cmd 8, arg 0... > <250.635356> slamr0: modem set state: 9 --> 1... > <250.635379> slamr0: new state: MODEM_IDLE > <250.635399> slamr0: modem report result: 3 (NO > CARRIER) > <250.635438> main: dev write = 0 > <256.757560> main: pty closed. > <256.757650> slamr0: modem_hup... > <256.757835> slamr0: update termios... > symbolic link `/dev/ttySL0' -> `/dev/pts/3' created. > <260.681684> main: signal 2: mark termination. > <260.681797> slamr0: modem_delete... > $ > > > //////////////////////////////////// > LOG OF SECOND TERMINAL > $ sudo wvdial -C ./wvdial.bcooper > Password: > --> WvDial: Internet dialer version 1.56 > --> Cannot get information for serial port. > --> Initializing modem. > --> Sending: ATZ > ATZ > OK > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > OK > --> Modem initialized. > --> Sending: ATDT6875000 > --> Waiting for carrier. > ATDT6875000 > CONNECT 46667 > --> Carrier detected. Waiting for prompt. > ** Ascend TNT Terminal Server ** > Login: > --> Looks like a login prompt. > --> Sending: acooper > acooper > Password: > --> Looks like a password prompt. > --> Sending: (password) > ** Bad Password > Login: > --> Looks like a login prompt. > --> Sending: acooper > acooper > Password: > --> Looks like a password prompt. > --> Sending: (password) > ** Bad Password > Login: > --> Looks like a login prompt. > --> Sending: acooper > --> Don't know what to do! Starting pppd and hoping > for the best. > --> Starting pppd at Tue Nov 13 16:16:44 2007 > --> Pid of pppd: 8329 > --> Using interface ppp0 > --> pppd: P [06][08]�[13][06][08] > --> pppd: P [06][08]�[13][06][08] > --> pppd: P [06][08]�[13][06][08] > --> pppd: P [06][08]�[13][06][08] > --> pppd: P [06][08]�[13][06][08] > --> pppd: P [06][08]�[13][06][08] > --> local IP address 216.167.135.22 > --> pppd: P [06][08]�[13][06][08] > --> remote IP address 65.182.79.66 > --> pppd: P [06][08]�[13][06][08] > --> primary DNS address 216.167.161.35 > --> pppd: P [06][08]�[13][06][08] > Caught signal 2: Attempting to exit gracefully... > --> Terminating on signal 15 > --> pppd: P [06][08]�[13][06][08] > --> Connect time 0.7 minutes. > --> pppd: P [06][08]�[13][06][08] > --> pppd: P [06][08]�[13][06][08] > --> Disconnecting at Tue Nov 13 16:17:30 2007 > $ > > ///////////////////////////////// > SECOND RUN WITH BCOOPER1 > ///////////////////////////////// > LOG OF FIRST TERMINAL > $ sudo ./startmodem > SHUTTING DOWN eth0 > eth0: ERROR while getting interface flags: No such > device > TOGGLE SLAMR > SHUT DOWN sl-modem-daemon > Shutting down SmartLink Modem driver normally ... no > slmodemd daemon running. > Unloading modem driver from kernel ... slamr. > START SLMODEMD > AFTER IT SETTLES, START SUDO WVDIAL IN A SEPARATE > TERMINAL WINDOW > SmartLink Soft Modem: version 2.9.11 May 26 2007 > 13:41:57 > <590.955579> SmartLink Soft Modem: version 2.9.11 May > 26 2007 13:41:57 > <590.956150> slamr0: startup modem... > <590.956357> slamr0: update termios... > symbolic link `/dev/ttySL0' -> `/dev/pts/2' created. > modem `slamr0' created. TTY is `/dev/pts/2' > <590.957396> open file: > /var/lib/slmodem/data.slamr0... > <590.957525> cannot open > '/var/lib/slmodem/data.slamr0': No such file or > directory > <590.958411> main: rt applyed: SCHED_FIFO, pri 99 > Use `/dev/ttySL0' as modem device, Ctrl+C for > termination. > <624.639400> main: termios changed. > <624.639486> slamr0: update termios... > <624.736543> main: termios changed. > <624.736625> slamr0: update termios... > <624.840385> slamr0: run cmd: ATZ > <624.840465> slamr0: modem reset... > <624.840485> slamr0: modem set state: 1 --> 1... > <624.840507> slamr0: modem set mode: -> 0... > <624.840527> slamr0: modem report result: 0 (OK) > <624.940484> slamr0: run cmd: > ATQ0V1E1S0=0&C1&D2+FCLASS=0 > <624.940575> slamr0: modem set mode: -> 0... > <624.940596> slamr0: modem report result: 0 (OK) > <625.040574> slamr0: run cmd: ATDT6875000 > <625.040664> slamr0: modem dial: T6875000... > <625.040685> slamr0: modem_dial_start... > <625.041415> slamr0: modem_start.. > <625.041436> slamr0: modem set state: 1 --> 2... > <625.041456> slamr0: new state: DP_ESTAB > <625.041476> main: modemap_ioctl: cmd 8, arg 3... > <625.041503> slamr0: modem set hook: 0 --> 1... > <625.041523> main: modemap_ioctl: cmd 2, arg 1... > <625.041552> main: modemap_ioctl: cmd 11, arg 0... > <625.041650> main: modemap_ioctl: cmd 4, arg 2580... > <625.041674> main: modemap_ioctl: cmd 7, arg 30... > <625.041694> main: modemap_start... > <636.436337> slamr0: 109344: change dp: --> 8... > <639.286153> main: modemap_ioctl: cmd 10, arg 0... > <639.286218> slamr0: 136704: change dp: --> 90... > <639.289516> main: modemap_ioctl: cmd 10, arg 0... > <639.291017> main: change delay -48... > <639.296017> main: change delay -48... > <639.301006> main: change delay -4... > <641.196080> main: change delay +384... > <655.474885> slamr0: modem_update_status: 256 > <655.474918> slamr0: --> DP LINK > <655.474937> slamr0: modem set state: 2 --> 4... > <655.474957> slamr0: new state: EC_ESTAB > <655.534644> slamr0: detector start... > <655.689881> slamr0: rx pattern: 0xa2. > <655.694824> slamr0: rx pattern: 0xc2. > <655.694856> slamr0: rx pattern: 0xa2. > <655.694876> slamr0: rx pattern: 0xc2. > <655.699585> slamr0: detector finished. > <655.699610> slamr0: modem_update_status: 1024 > <655.699630> slamr0: --> PACK LINK > <655.699649> slamr0: hdlc_start... > <655.879841> slamr0: modem update config... > <655.879887> slamr0: ec = 1 (1) > <655.879906> slamr0: ec_detector = 1 (1) > <655.879926> slamr0: ec_tx_win_size = 15 (15) > <655.879945> slamr0: ec_rx_win_size = 15 (15) > <655.879964> slamr0: ec_tx_info_size = 128 (128) > <655.879983> slamr0: ec_rx_info_size = 128 (128) > <655.880003> slamr0: comp = 3 (3) > <655.880022> slamr0: comp_dict_size = 2048 (2048) > <655.880041> slamr0: comp_max_string = 32 (34) > <656.009810> slamr0: hdlc frame size error. > <656.014786> slamr0: hdlc frame fcs error. > <656.014816> slamr0: hdlc frame fcs error. > <656.719743> slamr0: modem_update_status: 4096 > <656.719789> slamr0: --> EC LINK > <656.719809> slamr0: modem set state: 4 --> 5... > <656.719829> slamr0: new state: MODEM_ONLINE > <656.719848> slamr0: modem report result: 1 (CONNECT) > <656.719882> main: modemap_ioctl: cmd 8, arg 0... > <656.849821> slamr0: hdlc frame size error. > <656.849867> slamr0: hdlc frame size error. > <656.854710> slamr0: hdlc frame size error. > <657.529654> slamr0: hdlc frame size error. > <658.924510> slamr0: hdlc frame size error. > <659.024505> slamr0: hdlc frame size error. > <661.389290> slamr0: hdlc frame integrity error. > <664.269130> slamr0: hdlc frame size error. > <664.269186> slamr0: hdlc frame fcs error. > <664.269207> slamr0: hdlc frame integrity error. > <665.224202> main: termios changed. > <665.224249> slamr0: update termios... > <665.693924> slamr0: hdlc frame size error. > <666.138968> slamr0: hdlc frame size error. > <666.143989> slamr0: hdlc frame fcs error. > <666.144032> slamr0: hdlc frame size error. > <668.363668> slamr0: hdlc frame size error. > <674.303213> slamr0: hdlc frame size error. > <674.303262> slamr0: hdlc frame fcs error. > <675.188096> slamr0: hdlc frame size error. > <675.188144> slamr0: hdlc frame fcs error. > <675.188164> slamr0: hdlc frame integrity error. > <680.347602> slamr0: hdlc frame size error. > <680.347650> slamr0: hdlc frame size error. > <680.347670> slamr0: hdlc frame integrity error. > <691.851639> slamr0: modem_update_status: 8192 > <691.851680> slamr0: --> EC UNLINK > <691.851700> slamr0: modem_hup... > <691.851719> slamr0: modem set state: 5 --> 9... > <691.851740> slamr0: new state: DP_DISC > <691.851778> slamr0: modem_stop.. > <691.851797> main: modemap_stop... > <691.851849> slamr0: modem set hook: 1 --> 0... > <691.851869> main: modemap_ioctl: cmd 2, arg 0... > <691.851900> main: modemap_ioctl: cmd 8, arg 0... > <691.852212> slamr0: modem set state: 9 --> 1... > <691.852235> slamr0: new state: MODEM_IDLE > <691.852254> slamr0: modem report result: 3 (NO > CARRIER) > <691.852290> main: dev write = 0 > <698.014517> main: pty closed. > <698.014610> slamr0: modem_hup... > <698.014754> slamr0: update termios... > symbolic link `/dev/ttySL0' -> `/dev/pts/3' created. > <705.619698> main: signal 2: mark termination. > <705.619808> slamr0: modem_delete... > $ > > ///////////////////////////////////////// > LOG OF SECOND TERMINAL > $ sudo wvdial -C wvdial.bcooper > --> WvDial: Internet dialer version 1.56 > --> Cannot get information for serial port. > --> Initializing modem. > --> Sending: ATZ > ATZ > OK > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > OK > --> Modem initialized. > --> Sending: ATDT6875000 > --> Waiting for carrier. > ATDT6875000 > CONNECT 46667 > --> Carrier detected. Waiting for prompt. > ** Ascend TNT Terminal Server ** > Login: > --> Looks like a login prompt. > --> Sending: bcooper1 > bcooper1 > Password: > --> Looks like a password prompt. > --> Sending: (password) > ** Bad Password > Login: > --> Looks like a login prompt. > --> Sending: bcooper1 > bcooper1 > Password: > --> Looks like a password prompt. > --> Sending: (password) > ** Bad Password > Login: > --> Looks like a login prompt. > --> Sending: bcooper1 > --> Don't know what to do! Starting pppd and hoping > for the best. > --> Starting pppd at Tue Nov 13 16:24:25 2007 > --> Pid of pppd: 8833 > --> Using interface ppp0 > --> pppd: P [06][08]�[13][06][08] > --> pppd: P [06][08]�[13][06][08] > --> pppd: P [06][08]�[13][06][08] > --> pppd: P [06][08]�[13][06][08] > --> pppd: P [06][08]�[13][06][08] > --> pppd: P [06][08]�[13][06][08] > --> local IP address 216.167.135.30 > --> pppd: P [06][08]�[13][06][08] > --> remote IP address 65.182.79.66 > --> pppd: P [06][08]�[13][06][08] > --> primary DNS address 216.167.161.35 > --> pppd: P [06][08]�[13][06][08] > Caught signal 2: Attempting to exit gracefully... > --> Terminating on signal 15 > --> pppd: P [06][08]�[13][06][08] > --> Connect time 0.4 minutes. > --> pppd: P [06][08]�[13][06][08] > --> pppd: P [06][08]�[13][06][08] > --> Disconnecting at Tue Nov 13 16:24:51 2007 > $ > > > > Bob Terrell > Lubbock, Texas > bob_terrell_texas@xxxxxxxxx > > > > > > ____________________________________________________________________________________ > Be a better pen pal. > Text or chat with friends inside Yahoo! Mail. See how. > http://overview.mail.yahoo.com/ >
