Ciro, After an usual success with the slamr driver for a 1057:3052 chipset modem, I put the recogition codes for other Motorola modems in the slamr ccode, including your 1057:5600 in hope they might also be served. But from the failure you report and also one prior, it seems that 1057:5600 cannot thus be supported. You will need other modem hardware for service under Linux. Read the InfoGeneral.txt about the alternatives. Condolences, MarvS scanModem maintainer On 8/20/07, Ciro Rocha <ciro.rocha@xxxxxxxxx> wrote: > Hi, > > I'm trying to run a Motorola SM56 Speakerphone Modem device ID 1057:5600. > Down there is ModemData.txt from scanModem, followed by my dmesg. > I appreciate any help, and I want to cooperate too, just need to know > where to start. =] > > Thanks in advance to anyone who respond this. > > > -------------------------------------------------------------------------------------------------------------------- > > Only plain text email is forwarded by the DISCUSS@xxxxxxxxxxxxx List Server. > Do use the following as the email Subject Line: > SomeName, YourCountry Ubuntu 7.04 kernel 2.6.20-16-generic > This will alert cogent experts, and distinguish cases in the Archives. > YourCountry will enable Country Code guidance. > Occassionally responses are blocked by an Internet Provider mail filters. > So in a day, also check the Archived responses at http://www.linmodems.org . > Local Linux experts can be found through: > http://www.linux.org/groups/index.html > -------------------------- System information ---------------------------- > CPU=i686, Ubuntu 7.04 > Linux version 2.6.20-16-generic (root@terranova) (gcc version 4.1.2 > (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Thu Jun 7 20:19:32 UTC 2007 > scanModem update of: 2007_August_10 > The modem symbolic link is /dev/modem -> ttySL0 > > ALSAversion 1.0.13 > USB modem not detected by lsusb > > Modem or host audio card candidates have firmware information: > > PCI slot PCI ID SubsystemID Name > ---------- --------- --------- -------------- > 00:0a.0 1057:5600 1057:0300 Communication controller: Motorola SM56 PCI Modem > > Modem interrupt assignment and sharing: > 21: 301419 IO-APIC-fasteoi SiS SI7012 > > --- Bootup diagnostics for card in PCI slot 00:0a.0 ---- > [ 50.165711] ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, > low) -> IRQ 21 > [ 50.166237] ACPI: PCI interrupt for device 0000:00:0a.0 disabled > > The PCI slot 00:0a.0 of the modem card may be disabled early in > a bootup process, but then enabled later. If modem drivers load > but the modem is not responsive, read Bootup.txt about possible fixes. > Send dmesg.txt along with ModemData.txt to discuss@xxxxxxxxxxxxx > if help is needed. > > > === Finished modem firmware and bootup diagnostics section. === > === Next deducing cogent software === > > For candidate modem in PCI bus: 00:0a.0 > Class 0780: 1057:5600 Communication controller: Motorola SM56 PCI Modem > Primary PCI_id 1057:5600 > Support type needed or chipset: Motorola > > > > Completed candidate modem analyses. > > The base of the UDEV device file system is: /dev/.udev > > Versions adequately match for the compiler installed: 4.1.2 > and the compiler used in kernel assembly: 4.1.2 > > Kernel-header resources needed for compiling are not manifestly ready! > > If compiling is necessary packages must be installed, providing: > linux-headers-2.6.20-16-generic > > > If a driver compilation files with message including some lack of some > FileName.h (stdio.h for example. > Some additional kernel-header files need installation to /usr/include. > For Debian/Ubuntu related distributions, run the following command to > display the needed package list: > $ sudo apt-get -s install linux-kernel-devel > While some of the files may be on the install CD, others may have to > be found through http://packages.ubuntu.com > > For Ubunut feisty, additional packages required were: > build-essential curl debhelper dpkg-dev g++ g++-4.1 gettext git-core gitk > html2text intltool-debian kernel-package kernel-wedge libc6-dev > libcurl3-gnutls libdigest-sha1-perl liberror-perl libstdc++6-4.1-dev > linux-libc-dev po-debconf rcs tcl8.4 tk8.4 > > > Checking pppd properties: > -rwsr-xr-- 1 root dip 269224 2007-04-05 00:41 /usr/sbin/pppd > > In case of an "error 17" "serial loopback" problem, see: > http://phep2.technion.ac.il/linmodems/archive-sixth/msg02637.html > > To enable dialout without Root permission do: > $ su - root (not for Ubuntu) > sudo chmod a+x /usr/sbin/pppd > or under Ubuntu related Linuxes > sudo chmod a+x /usr/sbin/pppd > > Checking settings of: /etc/ppp/options > asyncmap 0 > noauth > crtscts > lock > hide-password > modem > proxyarp > lcp-echo-interval 30 > lcp-echo-failure 4 > noipx > > In case of a message like: > Warning: Could not modify /etc/ppp/pap-secrets: Permission denied > see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html > > Read Modem/YourSystem.txt concerning other COMM channels: eth0 > Which can interfere with Browser naviagation. > > Don't worry about the following, it is for the experts > should trouble shooting be necessary. > ========================================================== > > # start/stop the daemon when the USB modem is connected > KERNEL=="slusb[0-9]*", GROUP="dialout", RUN+="/etc/init.d/sl-modem-daemon" > Checking for modem support lines: > -------------------------------------- > /device/modem symbolic link: lrwxrwxrwx 1 root root 6 > 2007-08-20 15:03 /dev/modem -> ttySL0 > slmodemd created symbolic link /dev/ttySL0: > Within /etc/udev/ files: > /etc/udev/rules.d/030_sl-modem-daemon.rules:# start/stop the daemon > when the USB modem is connected > /etc/udev/rules.d/030_sl-modem-daemon.rules:KERNEL=="slusb[0-9]*", > GROUP="dialout", RUN+="/etc/init.d/sl-modem-daemon" > /etc/udev/sl-modem-daemon.rules:# start/stop the daemon when the USB > modem is connected > /etc/udev/sl-modem-daemon.rules:KERNEL=="slusb[0-9]*", > GROUP="dialout", RUN+="/etc/init.d/sl-modem-daemon" > Within /etc/modprobe.conf files: > /etc/modprobe.d/alsa-base:options snd-atiixp-modem index=-2 > /etc/modprobe.d/alsa-base:options snd-via82xx-modem index=-2 > /etc/modprobe.d/sl-modem-daemon.modutils:install slamr modprobe > --ignore-install ungrab-winmodem ; modprobe --ignore-install slamr; > test -e /dev/slamr0 || (/bin/mknod -m 660 /dev/slamr0 c 242 0 > 2>/dev/null && chgrp dialout /dev/slamr0) > /etc/modprobe.d/blacklist-modem:# Uncomment these entries in order to > blacklist unwanted modem drivers > /etc/modprobe.d/blacklist-modem:# blacklist snd-atiixp-modem > /etc/modprobe.d/blacklist-modem:# blacklist snd-via82xx-modem > Within any ancient /etc/devfs files: > > Within ancient kernel 2.4.n /etc/module.conf files: > > --------- end modem support lines -------- > > > dmesg | grep slamr > ---------------------------------------------------------------------------- > > [ 50.153295] slamr: module license 'Smart Link Ltd.' taints kernel. > [ 50.163582] slamr: SmartLink AMRMO modem. > [ 50.165687] slamr: probe 1057:5600 SL1900 card... > [ 50.166154] slamr: cannot init card. > > end of dmesg | grep slamr > --------------------------------------------------------------------- > > > > dmesg ----------------------------------------------------------------------------------------- > > [ 0.000000] Linux version 2.6.20-16-generic (root@terranova) (gcc > version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Thu Jun 7 20:19:32 UTC > 2007 (Ubuntu 2.6.20-16.29-generic) > [ 0.000000] BIOS-provided physical RAM map: > [ 0.000000] sanitize start > [ 0.000000] sanitize end > [ 0.000000] copy_e820_map() start: 0000000000000000 size: > 000000000009fc00 end: 000000000009fc00 type: 1 > [ 0.000000] copy_e820_map() type is E820_RAM > [ 0.000000] copy_e820_map() start: 000000000009fc00 size: > 0000000000000400 end: 00000000000a0000 type: 2 > [ 0.000000] copy_e820_map() start: 00000000000f0000 size: > 0000000000010000 end: 0000000000100000 type: 2 > [ 0.000000] copy_e820_map() start: 0000000000100000 size: > 000000001befc000 end: 000000001bffc000 type: 1 > [ 0.000000] copy_e820_map() type is E820_RAM > [ 0.000000] copy_e820_map() start: 000000001bffc000 size: > 0000000000003000 end: 000000001bfff000 type: 3 > [ 0.000000] copy_e820_map() start: 000000001bfff000 size: > 0000000000001000 end: 000000001c000000 type: 4 > [ 0.000000] copy_e820_map() start: 00000000fec00000 size: > 0000000000001000 end: 00000000fec01000 type: 2 > [ 0.000000] copy_e820_map() start: 00000000fee00000 size: > 0000000000001000 end: 00000000fee01000 type: 2 > [ 0.000000] copy_e820_map() start: 00000000ffff0000 size: > 0000000000010000 end: 0000000100000000 type: 2 > [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) > [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) > [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) > [ 0.000000] BIOS-e820: 0000000000100000 - 000000001bffc000 (usable) > [ 0.000000] BIOS-e820: 000000001bffc000 - 000000001bfff000 (ACPI data) > [ 0.000000] BIOS-e820: 000000001bfff000 - 000000001c000000 (ACPI NVS) > [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) > [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) > [ 0.000000] BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) > [ 0.000000] 0MB HIGHMEM available. > [ 0.000000] 447MB LOWMEM available. > [ 0.000000] Entering add_active_range(0, 0, 114684) 0 entries of 256 used > [ 0.000000] Zone PFN ranges: > [ 0.000000] DMA 0 -> 4096 > [ 0.000000] Normal 4096 -> 114684 > [ 0.000000] HighMem 114684 -> 114684 > [ 0.000000] early_node_map[1] active PFN ranges > [ 0.000000] 0: 0 -> 114684 > [ 0.000000] On node 0 totalpages: 114684 > [ 0.000000] DMA zone: 32 pages used for memmap > [ 0.000000] DMA zone: 0 pages reserved > [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 > [ 0.000000] Normal zone: 863 pages used for memmap > [ 0.000000] Normal zone: 109725 pages, LIFO batch:31 > [ 0.000000] HighMem zone: 0 pages used for memmap > [ 0.000000] DMI 2.3 present. > [ 0.000000] ACPI: RSDP (v000 ASUS > ) @ 0x000f5700 > [ 0.000000] ACPI: RSDT (v001 ASUS P4S800MX 0x42302e31 MSFT > 0x31313031) @ 0x1bffc000 > [ 0.000000] ACPI: FADT (v001 ASUS P4S800MX 0x42302e31 MSFT > 0x31313031) @ 0x1bffc0c0 > [ 0.000000] ACPI: BOOT (v001 ASUS P4S800MX 0x42302e31 MSFT > 0x31313031) @ 0x1bffc030 > [ 0.000000] ACPI: MADT (v001 ASUS P4S800MX 0x42302e31 MSFT > 0x31313031) @ 0x1bffc058 > [ 0.000000] ACPI: DSDT (v001 ASUS P4S800MX 0x00001000 MSFT > 0x0100000b) @ 0x00000000 > [ 0.000000] ACPI: PM-Timer IO Port: 0xe408 > [ 0.000000] ACPI: Local APIC address 0xfee00000 > [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) > [ 0.000000] Processor #0 15:4 APIC version 20 > [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) > [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) > [ 0.000000] IOAPIC[0]: apic_id 2, version 128, address 0xfec00000, GSI 0-23 > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge) > [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level) > [ 0.000000] ACPI: IRQ0 used by override. > [ 0.000000] ACPI: IRQ2 used by override. > [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs > [ 0.000000] Using ACPI (MADT) for SMP configuration information > [ 0.000000] Allocating PCI resources starting at 20000000 (gap: > 1c000000:e2c00000) > [ 0.000000] Detected 2801.136 MHz processor. > [ 14.584932] Built 1 zonelists. Total pages: 113789 > [ 14.584938] Kernel command line: > root=UUID=4fdeb564-b393-4bf0-8218-a270bdb84e03 ro > [ 14.585098] mapped APIC to ffffd000 (fee00000) > [ 14.585101] mapped IOAPIC to ffffc000 (fec00000) > [ 14.585104] Enabling fast FPU save and restore... done. > [ 14.585108] Enabling unmasked SIMD FPU exception support... done. > [ 14.585118] Initializing CPU#0 > [ 14.585199] PID hash table entries: 2048 (order: 11, 8192 bytes) > [ 14.586302] Console: colour VGA+ 80x25 > [ 14.589161] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) > [ 14.589512] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) > [ 14.597483] Memory: 443704k/458736k available (1992k kernel code, > 14456k reserved, 900k data, 328k init, 0k highmem) > [ 14.597570] virtual kernel memory layout: > [ 14.597571] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB) > [ 14.597572] pkmap : 0xff800000 - 0xffc00000 (4096 kB) > [ 14.597573] vmalloc : 0xdc800000 - 0xff7fe000 ( 559 MB) > [ 14.597575] lowmem : 0xc0000000 - 0xdbffc000 ( 447 MB) > [ 14.597576] .init : 0xc03d9000 - 0xc042b000 ( 328 kB) > [ 14.597577] .data : 0xc02f2374 - 0xc03d36d4 ( 900 kB) > [ 14.597578] .text : 0xc0100000 - 0xc02f2374 (1992 kB) > [ 14.597979] Checking if this processor honours the WP bit even in > supervisor mode... Ok. > [ 14.677055] Calibrating delay using timer specific routine.. > 5605.63 BogoMIPS (lpj=11211278) > [ 14.677193] Security Framework v1.0.0 initialized > [ 14.677247] SELinux: Disabled at boot. > [ 14.677311] Mount-cache hash table entries: 512 > [ 14.677500] CPU: After generic identify, caps: bfebfbff 00000000 > 00000000 00000000 0000441d 00000000 00000000 > [ 14.677509] monitor/mwait feature present. > [ 14.677558] using mwait in idle threads. > [ 14.677612] CPU: Trace cache: 12K uops, L1 D cache: 16K > [ 14.677690] CPU: L2 cache: 1024K > [ 14.677737] CPU: Hyper-Threading is disabled > [ 14.677787] CPU: After all inits, caps: bfebfbff 00000000 00000000 > 00003180 0000441d 00000000 00000000 > [ 14.677798] Compat vDSO mapped to ffffe000. > [ 14.677848] Remapping vsyscall page to ffffe000 > [ 14.677912] Checking 'hlt' instruction... OK. > [ 14.693160] SMP alternatives: switching to UP code > [ 14.693374] Freeing SMP alternatives: 11k freed > [ 14.693624] Early unpacking initramfs... done > [ 14.984238] ACPI: Core revision 20060707 > [ 14.985167] ACPI: Looking for DSDT in initramfs... file /DSDT.aml > not found, using machine DSDT. > [ 14.986528] CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 01 > [ 14.986673] Total of 1 processors activated (5605.63 BogoMIPS). > [ 14.986825] ENABLING IO-APIC IRQs > [ 14.987053] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 > [ 15.132362] Brought up 1 CPUs > [ 15.132662] Booting paravirtualized kernel on bare hardware > [ 15.132789] Time: 18:02:38 Date: 07/20/107 > [ 15.132866] NET: Registered protocol family 16 > [ 15.133009] EISA bus registered > [ 15.133059] ACPI: bus type pci registered > [ 15.134758] PCI: PCI BIOS revision 2.10 entry at 0xf10c0, last bus=1 > [ 15.134812] PCI: Using configuration type 1 > [ 15.134861] Setting up standard PCI resources > [ 15.140589] ACPI: Interpreter enabled > [ 15.140639] ACPI: Using IOAPIC for interrupt routing > [ 15.141393] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) > [ 15.141984] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 > 12 14 15) *0, disabled. > [ 15.142648] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15) > [ 15.143248] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15) > [ 15.143844] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 12 14 15) > [ 15.144456] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 > 12 14 15) *9 > [ 15.145079] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 > 12 14 15) *0, disabled. > [ 15.145744] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 > 12 14 15) *9 > [ 15.146258] ACPI: PCI Root Bridge [PCI0] (0000:00) > [ 15.146315] PCI: Probing PCI hardware (bus 00) > [ 15.146675] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 > [ 15.147017] Enabling SiS 96x SMBus. > [ 15.147658] Boot video device is 0000:01:00.0 > [ 15.147716] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] > [ 15.148881] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] > [ 15.154101] Linux Plug and Play Support v0.97 (c) Adam Belay > [ 15.154163] pnp: PnP ACPI init > [ 15.159217] pnp: PnP ACPI: found 16 devices > [ 15.159270] PnPBIOS: Disabled by ACPI PNP > [ 15.159367] PCI: Using ACPI for IRQ routing > [ 15.159418] PCI: If a device doesn't work, try "pci=routeirq". If > it helps, post a report > [ 15.165537] NET: Registered protocol family 8 > [ 15.165587] NET: Registered protocol family 20 > [ 15.165921] pnp: 00:02: ioport range 0xe400-0xe47f could not be reserved > [ 15.165977] pnp: 00:02: ioport range 0xe480-0xe4ff has been reserved > [ 15.166031] pnp: 00:02: ioport range 0xe600-0xe61f has been reserved > [ 15.166084] pnp: 00:02: ioport range 0x480-0x48f has been reserved > [ 15.166150] pnp: 00:0f: ioport range 0x295-0x296 has been reserved > [ 15.166508] PCI: Ignore bogus resource 6 [0:0] of 0000:01:00.0 > [ 15.166561] PCI: Bridge: 0000:00:01.0 > [ 15.166610] IO window: d000-dfff > [ 15.166661] MEM window: e7800000-e7ffffff > [ 15.166713] PREFETCH window: f0000000-febfffff > [ 15.166777] PCI: Setting latency timer of device 0000:00:01.0 to 64 > [ 15.166806] NET: Registered protocol family 2 > [ 15.204286] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) > [ 15.204421] TCP established hash table entries: 16384 (order: 5, > 131072 bytes) > [ 15.204579] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) > [ 15.204676] TCP: Hash tables configured (established 16384 bind 8192) > [ 15.204730] TCP reno registered > [ 15.216318] checking if image is initramfs... it is > [ 15.784586] Freeing initrd memory: 6773k freed > [ 15.784888] Simple Boot Flag at 0x3a set to 0x1 > [ 15.785285] audit: initializing netlink socket (disabled) > [ 15.785353] audit(1187632959.280:1): initialized > [ 15.785537] VFS: Disk quotas dquot_6.5.1 > [ 15.785607] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) > [ 15.785713] io scheduler noop registered > [ 15.785790] io scheduler anticipatory registered > [ 15.785865] io scheduler deadline registered > [ 15.785947] io scheduler cfq registered (default) > [ 15.786289] isapnp: Scanning for PnP cards... > [ 16.137692] isapnp: No Plug & Play device found > [ 16.164156] Real Time Clock Driver v1.12ac > [ 16.164265] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, > IRQ sharing enabled > [ 16.164457] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > [ 16.165238] 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A > [ 16.165528] mice: PS/2 mouse device common for all mice > [ 16.166211] RAMDISK driver initialized: 16 RAM disks of 65536K size > 1024 blocksize > [ 16.166539] input: Macintosh mouse button emulation as /class/input/input0 > [ 16.166676] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 > [ 16.166732] ide: Assuming 33MHz system bus speed for PIO modes; > override with idebus=xx > [ 16.167059] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at > 0x60,0x64 irq 1,12 > [ 16.167446] serio: i8042 KBD port at 0x60,0x64 irq 1 > [ 16.167499] serio: i8042 AUX port at 0x60,0x64 irq 12 > [ 16.167660] EISA: Probing bus 0 at eisa.0 > [ 16.167740] Cannot allocate resource for EISA slot 8 > [ 16.167790] EISA: Detected 0 cards. > [ 16.197979] TCP cubic registered > [ 16.198033] NET: Registered protocol family 1 > [ 16.198106] Using IPI No-Shortcut mode > [ 16.198228] ACPI: (supports S0 S1 S4 S5) > [ 16.198448] Magic number: 3:386:39 > [ 16.198496] hash matches drivers/base/power/resume.c:56 > [ 16.198597] Time: tsc clocksource has been installed. > [ 16.198823] hash matches device 00:0b > [ 16.199139] Freeing unused kernel memory: 328k freed > [ 16.207689] input: AT Translated Set 2 keyboard as /class/input/input1 > [ 16.379655] Capability LSM initialized > [ 16.415379] ACPI: Invalid PBLK length [5] > [ 16.415473] ACPI Exception (acpi_processor-0677): AE_NOT_FOUND, > Processor Device is not present [20060707] > [ 16.847435] SIS5513: IDE controller at PCI slot 0000:00:02.5 > [ 16.847514] ACPI: PCI Interrupt 0000:00:02.5[A] -> GSI 16 (level, > low) -> IRQ 16 > [ 16.847619] SIS5513: chipset revision 0 > [ 16.847667] SIS5513: not 100% native mode: will probe irqs later > [ 16.847730] SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller > [ 16.847798] ide0: BM-DMA at 0xa400-0xa407, BIOS settings: > hda:DMA, hdb:DMA > [ 16.847929] ide1: BM-DMA at 0xa408-0xa40f, BIOS settings: > hdc:DMA, hdd:pio > [ 16.848056] Probing IDE interface ide0... > [ 16.879617] usbcore: registered new interface driver usbfs > [ 16.879699] usbcore: registered new interface driver hub > [ 16.879773] usbcore: registered new device driver usb > [ 16.880601] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller > (OHCI) Driver > [ 16.898511] sis900.c: v1.08.10 Apr. 2 2006 > [ 16.995209] Floppy drive(s): fd0 is 1.44M > [ 17.036998] FDC 0 is a post-1991 82077 > [ 17.161149] hda: QUANTUM FIREBALLlct20 20, ATA DISK drive > [ 17.612440] hdb: HL-DT-ST GCE-8527B, ATAPI CD/DVD-ROM drive > [ 17.692612] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > [ 17.706395] Probing IDE interface ide1... > [ 17.995784] hdc: WDC WD200AB-00BPA1, ATA DISK drive > [ 18.671429] ide1 at 0x170-0x177,0x376 on irq 15 > [ 18.700021] SCSI subsystem initialized > [ 18.706966] libata version 2.20 loaded. > [ 18.712260] ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, > low) -> IRQ 20 > [ 18.712375] ohci_hcd 0000:00:03.0: OHCI Host Controller > [ 18.712748] ohci_hcd 0000:00:03.0: new USB bus registered, assigned > bus number 1 > [ 18.712830] ohci_hcd 0000:00:03.0: irq 20, io mem 0xe7000000 > [ 18.721845] hda: max request size: 128KiB > [ 18.737700] hda: 39876480 sectors (20416 MB) w/418KiB Cache, > CHS=39560/16/63, UDMA(100) > [ 18.737887] hda: cache flushes not supported > [ 18.737990] hda: hda1 hda2 < hda5 > > [ 18.772493] usb usb1: configuration #1 chosen from 1 choice > [ 18.772578] hub 1-0:1.0: USB hub found > [ 18.772635] hub 1-0:1.0: 3 ports detected > [ 18.779634] hdc: max request size: 128KiB > [ 18.780667] hdc: 39102336 sectors (20020 MB) w/2048KiB Cache, > CHS=38792/16/63, UDMA(33) > [ 18.780844] hdc: cache flushes not supported > [ 18.780921] hdc:<6>hdb: ATAPI 52X CD-ROM CD-R/RW drive, 1536kB > Cache, UDMA(33) > [ 18.781884] Uniform CD-ROM driver Revision: 3.20 > [ 18.789145] hdc1 hdc2 < hdc5 > > [ 18.878357] ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, > low) -> IRQ 17 > [ 18.878476] ohci_hcd 0000:00:03.1: OHCI Host Controller > [ 18.878552] ohci_hcd 0000:00:03.1: new USB bus registered, assigned > bus number 2 > [ 18.878635] ohci_hcd 0000:00:03.1: irq 17, io mem 0xe6800000 > [ 18.940258] usb usb2: configuration #1 chosen from 1 choice > [ 18.940352] hub 2-0:1.0: USB hub found > [ 18.940411] hub 2-0:1.0: 3 ports detected > [ 19.046189] ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, > low) -> IRQ 18 > [ 19.046305] ehci_hcd 0000:00:03.3: EHCI Host Controller > [ 19.046380] ehci_hcd 0000:00:03.3: new USB bus registered, assigned > bus number 3 > [ 19.046481] PCI: cache line size of 128 is not supported by device > 0000:00:03.3 > [ 19.046493] ehci_hcd 0000:00:03.3: irq 18, io mem 0xe6000000 > [ 19.046551] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, > driver 10 Dec 2004 > [ 19.046691] usb usb3: configuration #1 chosen from 1 choice > [ 19.046775] hub 3-0:1.0: USB hub found > [ 19.046829] hub 3-0:1.0: 6 ports detected > [ 19.154003] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, > low) -> IRQ 19 > [ 19.155466] 0000:00:04.0: VIA 6103 PHY transceiver found at address 1. > [ 19.166582] 0000:00:04.0: Using transceiver found at address 1 as default > [ 19.167518] eth0: SiS 900 PCI Fast Ethernet at 0x8800, IRQ 19, > 00:11:d8:91:39:06. > [ 19.345263] Attempting manual resume > [ 19.345314] swsusp: Resume From Partition 3:1 > [ 19.345316] PM: Checking swsusp image. > [ 19.355385] PM: Resume from disk failed. > [ 19.401581] kjournald starting. Commit interval 5 seconds > [ 19.401648] EXT3-fs: mounted filesystem with ordered data mode. > [ 36.575478] NET: Registered protocol family 10 > [ 36.575644] lo: Disabled Privacy Extensions > [ 37.830682] Linux agpgart interface v0.102 (c) Dave Jones > [ 37.914476] sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0xe600 > [ 37.969424] agpgart: Detected SiS 661 chipset > [ 37.974198] agpgart: AGP aperture is 64M @ 0xe8000000 > [ 38.263821] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 > [ 38.280685] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 > [ 38.344975] input: PC Speaker as /class/input/input2 > [ 38.433081] parport: PnPBIOS parport detected. > [ 38.433239] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 > [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] > [ 38.701446] ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, > low) -> IRQ 21 > [ 39.044693] input: ImPS/2 Generic Wheel Mouse as /class/input/input3 > [ 39.125085] intel8x0_measure_ac97_clock: measured 56376 usecs > [ 39.125147] intel8x0: clocking to 48000 > [ 39.209649] eth0: Media Link On 100mbps full-duplex > [ 39.279820] fuse init (API version 7.8) > [ 39.323532] lp0: using parport0 (interrupt-driven). > [ 39.349727] Adding 875500k swap on > /dev/disk/by-uuid/f30c6817-436a-4db2-a276-eb2570608361. Priority:-1 > extents:1 across:875500k > [ 39.517159] EXT3 FS on hda5, internal journal > [ 41.016231] NET: Registered protocol family 17 > [ 45.756402] ibm_acpi: ec object not found > [ 45.881176] input: Power Button (FF) as /class/input/input4 > [ 45.885378] ACPI: Power Button (FF) [PWRF] > [ 45.921017] input: Power Button (CM) as /class/input/input5 > [ 45.925220] ACPI: Power Button (CM) [PWRB] > [ 45.955142] Using specific hotkey driver > [ 46.075203] No dock devices found. > [ 46.199888] pcc_acpi: loading... > [ 47.383554] eth0: no IPv6 routers present > [ 50.153295] slamr: module license 'Smart Link Ltd.' taints kernel. > [ 50.163582] slamr: SmartLink AMRMO modem. > [ 50.165687] slamr: probe 1057:5600 SL1900 card... > [ 50.165711] ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, > low) -> IRQ 21 > [ 50.166154] slamr: cannot init card. > [ 50.166237] ACPI: PCI interrupt for device 0000:00:0a.0 disabled > [ 50.960415] ppdev: user-space parallel port driver > [ 52.870403] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) > [ 52.870410] apm: overridden by ACPI. > [ 53.043531] vboxdrv: Trying to deactivate NMI watchdog permanently... > [ 53.043538] vboxdrv: Successfully done. > [ 53.359318] Bluetooth: Core ver 2.11 > [ 53.359389] NET: Registered protocol family 31 > [ 53.359391] Bluetooth: HCI device and connection manager initialized > [ 53.359394] Bluetooth: HCI socket layer initialized > [ 53.416878] Bluetooth: L2CAP ver 2.8 > [ 53.416884] Bluetooth: L2CAP socket layer initialized > [ 53.620642] Bluetooth: RFCOMM socket layer initialized > [ 53.620658] Bluetooth: RFCOMM TTY layer initialized > [ 53.620660] Bluetooth: RFCOMM ver 1.8 > > end of dmesg -------------------------------------------------------------------------------------------------- >