I have installes slmodem-2.9.11-20061021 in Kubuntu Dapper.
First I send Modem.Data of scanModem:
-------------------------- System information ----------------------------
Ubuntu 6.06.1 LTS
Linux version 2.6.15-26-386 (buildd@terranova) (gcc version 4.0.3
(Ubuntu 4.0.3-1ubuntu5)) #1 PREEMPT Thu Aug 3 02:52:00 UTC 2006
scanModem update of: 2006_December_25
idVendor 0x1267 Logic3 / SpectraVideo plc
idProduct 0x0210
Bus 001 Device 004: ID 0483:7554 SGS Thomson Microelectronics 56k SoftModem
idVendor 0x0483 SGS Thomson Microelectronics
idProduct 0x7554 56k SoftModem
idVendor 0x045e Microsoft Corp.
idProduct 0x008a Wireless Keyboard and Mouse
Modem or host audio card candidates have firmware information:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
0000:00:14.2 1002:437b 1025:009f 0403: ATI Technologies Inc: Unknown
device 437b
Modem interrupt assignment and sharing:
209: 4875 IO-APIC-level HDA Intel
--- Bootup diagnositcs for card in PCI slot 0000:00:14.2 ----
=== Finished modem firmware and bootup diagnostics section. ===
=== Next deducing cogent software ===
1002:437b is a High Definition Audio card, possibly hosting a soft modem.
The VendorID 0x14f12bfa softmodem chip is in principle supported by the
snd-hda-intel driver
included within the ALSA audio+modem driver set. However recognition of
0x14f12bfa first begins with ALSA version 1.0.13. There are instructions
for upgrading snd-hda-intel and its
dependent driver set at
http://linmodems.technion.ac.il/archive-fourth/msg0????.html
The ? in the device designation in hw:0,? will be manifest after the
driver update.
Typically ? is in the range of 0-6 .
For candidate modem in PCI bus: 0000:00:14.2
Class 0403: 1002:437b 0403: ATI Technologies Inc: Unknown device 437b
Primary PCI_id 1002:437b
Subsystem PCI_id 1025:009f
Softmodem codec or Vendor from diagnostics: 14f1, a Conexant type,
from Archives: 14f1, a Conexant type,
Lacking a dsp (digital signal processing) chip, the modem is a software
intensive or "softmodem" type. Its primary controller manages the traffic
with the CPU. But the software needed is specified in the Subsystem.
-----------------------------------------
Support type needed or chipset: hsfmodem
The diagnostic outputs for this softmodem section have their raw
information in
folders and text files under /proc/asound/ which you can browse. The
information
is from files:
/proc/asound/pcm
-------------------------------
00-00: ALC883 Analog : ALC883 Analog : playback 1 : capture 2
00-01: ALC883 Analog : ALC883 Analog : capture 2
00-02: ALC883 Digital : ALC883 Digital : playback 1
/proc/asound/modules
-------------------------------
0 snd_hda_intel
/proc/asound/card0/codec#1
-------------------------------
Codec: Generic 14f1 ID 2bfa
Address: 1
Vendor Id: 0x14f12bfa
Subsystem Id: 0x1025009f
Revision Id: 0x90000
-------------------------------
Current support status of HDA cards is:
Vendor IDs Chip maker Support type
---------- ---------- -------------
0x14f12bfa Conexant hsfmodem , not slmodemd compatible
0x11c13026 AgereSystems snd-hda-intel, slmodemd supported
0x11c11040 AgereSystems " " , patch needed
0x11c13055 AgereSystems " " , "
0x163c3055 Smartlink " " , "
0x163c3155 " " " , "
0x10573055 Motorola " " , "
0x10573155 " " " , ""
as of October 2006.
and from the command:
aplay -l | grep -i modem
----------------end Softmodem section --------------
I wanted to go in Internet with Microlink 56k Fun USB.
So I did: modprobe slusb - slmodemd -c GERMANY -d /dev/slusb. In the
other console I wrote: wvdial. The effect.
l
--> WvDial: Internet dialer version 1.55
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Sending: ATDT01920783
--> Waiting for carrier.
No internet side, the modem was only waiting for carrier.
The bug of slmodemd -c GERMANY -d /dev/slub0
Script started on Di 02 Jan 2007 18:04:31 CET
]0;root@yollywau-laptop: ~ root@yollywau-laptop:~# slmodemd -c GERMANY
-d /dev/slusb0
SmartLink Soft Modem: version 2.9.11 Jan 2 2007 18:03:05
<491.978166> SmartLink Soft Modem: version 2.9.11 Jan 2 2007 18:03:05
<491.978602> slusb0: startup modem...
<491.978967> slusb0: update termios...
symbolic link `/dev/ttySL0' -> `/dev/pts/3' created.
modem `slusb0' created. TTY is `/dev/pts/3'
<491.980686> open file: /var/lib/slmodem/data.slusb0...
The folder /var/lib/slmodem was empty. A day later, there is - I don?t
know why a data.slusb0 in this folder , but it doesn?t find carrier.
After wvdial, it goes on in the debug report of slmodemd:
<735.960774> main: termios changed.
<735.960812> slusb0: update termios...
<736.079600> main: termios changed.
<736.079637> slusb0: update termios...
<736.179042> slusb0: run cmd: ATZ
<736.179081> slusb0: modem reset...
<736.179095> slusb0: modem set state: 1 --> 1...
<736.179111> slusb0: modem set mode: -> 0...
<736.179126> slusb0: modem report result: 0 (OK)
<736.279301> slusb0: run cmd: ATQ0V1E1S0=0&C1&D2+FCLASS=0
<736.279356> slusb0: modem set mode: -> 0...
<736.279371> slusb0: modem report result: 0 (OK)
<736.379367> slusb0: run cmd: ATDT01920783
<736.379416> slusb0: modem dial: T01920783...
<736.379431> slusb0: modem_dial_start...
<736.379484> slusb0: modem_start..
<736.379499> slusb0: modem set state: 1 --> 2...
<736.379513> slusb0: new state: DP_ESTAB
<736.379527> main: modemap_ioctl: cmd 8, arg 3...
<736.379545> slusb0: modem set hook: 0 --> 1...
<736.379560> main: modemap_ioctl: cmd 2, arg 1...
<736.380285> main: modemap_ioctl: cmd 11, arg 0...
<736.380408> main: modemap_ioctl: cmd 4, arg 2580...
<736.380425> main: modemap_ioctl: cmd 7, arg 30...
<736.380441> main: modemap_start...
<745.388376> slusb0: 86291: change dp: --> 8...
<748.148405> main: modemap_ioctl: cmd 10, arg 0...
<748.148450> slusb0: 112786: change dp: --> 90...
<748.151189> main: modemap_ioctl: cmd 10, arg 0...
<748.153374> main: change delay -47...
<748.158358> main: change delay -49...
<748.163354> main: change delay -47...
<748.168354> main: change delay -9...
<750.373505> main: change delay +384...
<761.753426> main: change delay -48...
<761.758429> main: change delay -48...
<761.763427> main: change delay -48...
<761.768432> main: change delay -48...
<761.773433> main: change delay -48...
<761.778428> main: change delay -48...
<761.783435> main: change delay -48...
<761.788440> main: change delay -48...
<764.918579> slusb0: modem_update_status: 4
<764.918621> slusb0: --> FINISH.
<764.918635> slusb0: modem_hup...
<764.918649> slusb0: modem set state: 2 --> 9...
<764.918665> slusb0: new state: DP_DISC
<764.918678> slusb0: modem_stop..
<764.918692> main: modemap_stop...
<764.922441> slusb0: modem set hook: 1 --> 0...
<764.922462> main: modemap_ioctl: cmd 2, arg 0...
<764.923430> main: modemap_ioctl: cmd 8, arg 0...
<764.923672> slusb0: modem set state: 9 --> 1...
<764.923689> slusb0: new state: MODEM_IDLE
<764.923703> slusb0: modem report result: 3 (NO CARRIER)
<765.221347> slusb0: run cmd: ATDT01920783
<765.221386> slusb0: modem dial: T01920783...
<765.221401> slusb0: modem_dial_start...
<765.221451> slusb0: modem_start..
<765.221466> slusb0: modem set state: 1 --> 2...
<765.221481> slusb0: new state: DP_ESTAB
<765.221494> main: modemap_ioctl: cmd 8, arg 3...
<765.221511> slusb0: modem set hook: 0 --> 1...
<765.221525> main: modemap_ioctl: cmd 2, arg 1...
<765.222441> main: modemap_ioctl: cmd 11, arg 0...
<765.222566> main: modemap_ioctl: cmd 4, arg 2580...
<765.222582> main: modemap_ioctl: cmd 7, arg 30...
<765.222599> main: modemap_start...
<825.144933> slusb0: modem_tty_write: hangup...
<825.144973> slusb0: modem_hup...
<825.144987> slusb0: modem set state: 2 --> 9...
<825.145003> slusb0: new state: DP_DISC
<825.150808> slusb0: modem_stop..
<825.150831> main: modemap_stop...
<825.154760> slusb0: modem set hook: 1 --> 0...
<825.154781> main: modemap_ioctl: cmd 2, arg 0...
<825.155748> main: modemap_ioctl: cmd 8, arg 0...
<825.155781> slusb0: modem set state: 9 --> 1...
<825.155796> slusb0: new state: MODEM_IDLE
<825.155810> slusb0: modem report result: 3 (NO CARRIER)
<825.156127> slusb0: run cmd: ATDT01920783
<825.156146> slusb0: modem dial: T01920783...
<825.156162> slusb0: modem_dial_start...
<825.156208> slusb0: modem_start..
<825.156222> slusb0: modem set state: 1 --> 2...
<825.156237> slusb0: new state: DP_ESTAB
<825.156250> main: modemap_ioctl: cmd 8, arg 3...
<825.156265> slusb0: modem set hook: 0 --> 1...
<825.156280> main: modemap_ioctl: cmd 2, arg 1...
<825.157766> main: modemap_ioctl: cmd 11, arg 0...
<825.157892> main: modemap_ioctl: cmd 4, arg 2580...
<825.157909> main: modemap_ioctl: cmd 7, arg 30...
<825.157924> main: modemap_start...
<825.452623> slusb0: modem_tty_write: hangup...
<825.452659> slusb0: modem_hup...
<825.452673> slusb0: modem set state: 2 --> 9...
<825.452688> slusb0: new state: DP_DISC
<825.455829> slusb0: modem_stop..
<825.455856> main: modemap_stop...
<825.459767> slusb0: modem set hook: 1 --> 0...
<825.459789> main: modemap_ioctl: cmd 2, arg 0...
<825.460752> main: modemap_ioctl: cmd 8, arg 0...
<825.460787> slusb0: modem set state: 9 --> 1...
<825.460803> slusb0: new state: MODEM_IDLE
<825.460817> slusb0: modem report result: 3 (NO CARRIER)
<825.461192> slusb0: run cmd: ATDT01920783
<825.461212> slusb0: modem dial: T01920783...
<825.461227> slusb0: modem_dial_start...
<825.461275> slusb0: modem_start..
<825.461289> slusb0: modem set state: 1 --> 2...
<825.461303> slusb0: new state: DP_ESTAB
<825.461316> main: modemap_ioctl: cmd 8, arg 3...
<825.461331> slusb0: modem set hook: 0 --> 1...
<825.461345> main: modemap_ioctl: cmd 2, arg 1...
<825.462765> main: modemap_ioctl: cmd 11, arg 0...
<825.462878> main: modemap_ioctl: cmd 4, arg 2580...
<825.462894> main: modemap_ioctl: cmd 7, arg 30...
<825.462914> main: modemap_start...
<825.760702> slusb0: modem_tty_write: hangup...
<825.760769> slusb0: modem_hup...
<825.760783> slusb0: modem set state: 2 --> 9...
<825.760799> slusb0: new state: DP_DISC
<825.760866> slusb0: modem_stop..
<825.760881> main: modemap_stop...
<825.764769> slusb0: modem set hook: 1 --> 0...
<825.764793> main: modemap_ioctl: cmd 2, arg 0...
<825.765761> main: modemap_ioctl: cmd 8, arg 0...
<825.765800> slusb0: modem set state: 9 --> 1...
<825.765816> slusb0: new state: MODEM_IDLE
<825.765831> slusb0: modem report result: 3 (NO CARRIER)
My /etc/wvdial.conf
[Dialer Defaults]
Modem = /dev/ttySL0
Baud = 115200
Init1 = ATZ
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ISDN = 0
Modem Type = Analog Modem
Phone = .......
Username = arcor
Password = internet
Carrier check = no
Stupid Mode = yes
I don?t no what to do. It would be nice, if you can help me. Sorry my
bad English
Renate Kräußlich
I hope, I write to the right adress for seaking help with my modem-problem
Happy new year and thanks
