You either missed "ceil" parameter or it is missing on my page :) Without ceil it is the same as rate thus all classes are bounded in fact. Add ceil 100kbps to each line. devik On Fri, 7 Jun 2002, King Yung Tong wrote: > Thank you for your reply :) > I try to follow chapter 6 on your user guide. > > 1:1 > / \ > 1:2 1:12 > / \ > 1:10 1:11 > (prio1) (prio2) > > If 1:12 don't have any traffic, all the BW on 1:12 can be assigned to 1:2, > is that right? > > I try to put all these extra (from 1:12) to 1:10, my htb script is as > follows, and I use ethloop to test and I found that 1:10 will not get the > extra from 1:12. Could you tell me where I make a mistake? Thank you. > > echo Clean all the tc setup > ./tc qdisc del dev lo root > ./tc qdisc add dev lo root handle 1: htb default 12 > > ./tc class add dev lo parent 1: classid 1:1 htb rate 100kbps > ./tc class add dev lo parent 1:1 classid 1:2 htb rate 40kbps > ./tc class add dev lo parent 1:2 classid 1:10 htb rate 30kbps prio 0 > ./tc class add dev lo parent 1:2 classid 1:11 htb rate 10kbps prio 1 > ./tc class add dev lo parent 1:1 classid 1:12 htb rate 60kbps > > echo qdisc > ./tc qdisc add dev lo parent 1:10 handle 20: pfifo limit 5 > ./tc qdisc add dev lo parent 1:11 handle 30: pfifo limit 5 > ./tc qdisc add dev lo parent 1:12 handle 40: sfq perturb 10 > > Input for ethloop: > > # lo will be used to TX and RX > 0 i 0 lo > 0 i 1 lo > 0 i 2 lo > # set simulation packet size to 1k > 0 S 0 1k > 0 S 1 1k > 0 S 2 1k > # flow 0 AE, flow 1 BE, flow 2 EF > 0 P 0 0x10010 > 0 P 1 0x10011 > 0 P 2 0x10012 > # start all flow at defined rate > 0 R 0 30000 > 0 R 1 10000 > 0 R 2 60000 > # Create extra at 1:12 and borrow this to 1:2 <------? > 5000 R 0 30000 > 5000 R 1 10000 > 5000 R 2 0 > # 1:10 and 1:11 and 1:10 should get higher value <------? > 15000 R 0 40000 > 15000 R 1 20000 > # finish at 8sec > 25000 X 0 0 > > Result is to long, I use gnuplot and found that 1:10 at most get 30000. > > Thank you for you help. > > Pat > > > > On Fri, 7 Jun 2002, Martin Devera wrote: > > > What is the problem ? use cat ethloop_script|./ethloop > > for example .. > > devik > > > > On Thu, 6 Jun 2002, King Yung Tong wrote: > > > > > _______________________________________________ LARTC mailing list / LARTC@mailman.ds9a.nl http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
