Gleb Natapov wrote on 2013-02-05:
> On Tue, Feb 05, 2013 at 10:58:28AM +0000, Zhang, Yang Z wrote:
>> Gleb Natapov wrote on 2013-02-05:
>>> On Tue, Feb 05, 2013 at 10:35:55AM +0000, Zhang, Yang Z wrote:
>>>> Gleb Natapov wrote on 2013-02-05:
>>>>> On Tue, Feb 05, 2013 at 05:57:14AM +0000, Zhang, Yang Z wrote:
>>>>>> Marcelo Tosatti wrote on 2013-02-05:
>>>>>>> On Mon, Feb 04, 2013 at 05:59:52PM -0200, Marcelo Tosatti wrote:
>>>>>>>> On Mon, Feb 04, 2013 at 07:13:01PM +0200, Gleb Natapov wrote:
>>>>>>>>> On Mon, Feb 04, 2013 at 12:43:45PM -0200, Marcelo Tosatti wrote:
>>>>>>>>>>>> Any example how software relies on such
>>>>>>> two-interrupts-queued-in-IRR/ISR behaviour?
>>>>>>>>>>> Don't know about guests, but KVM relies on it to detect
>>>>>>>>>>> interrupt coalescing. So if interrupt is set in IRR but not in
>>>>>>>>>>> PIR interrupt will not be reported as coalesced, but it will
>>>>>>>>>>> be coalesced during PIR->IRR merge.
>>>>>>>>>>
>>>>>>>>>> Yes, so:
>>>>>>>>>>
>>>>>>>>>> 1. IRR=1, ISR=0, PIR=0. Event: set_irq, coalesced=no.
>>>>>>>>>> 2. IRR=0, ISR=1, PIR=0. Event: IRR->ISR transfer.
>>>>>>>>>> 3. vcpu outside of guest mode.
>>>>>>>>>> 4. IRR=1, ISR=1, PIR=0. Event: set_irq, coalesced=no.
>>>>>>>>>> 5. vcpu enters guest mode.
>>>>>>>>>> 6. IRR=1, ISR=1, PIR=1. Event: set_irq, coalesced=no.
>>>>>>>>>> 7. HW transfers PIR into IRR.
>>>>>>>>>>
>>>>>>>>>> set_irq return value at 7 is incorrect, interrupt event was _not_
>>>>>>>>>> queued.
>>>>>>>>> Not sure I understand the flow of events in your description
>>>>>>>>> correctly. As I understand it at 4 set_irq() will return incorrect
>>>>>>>>> result. Basically when PIR is set to 1 while IRR has 1 for the
>>>>>>>>> vector the value of set_irq() will be incorrect.
>>>>>>>>
>>>>>>>> At 4 it has not been coalesced: it has been queued to IRR.
>>>>>>>> At 6 it has been coalesced: PIR bit merged into IRR bit.
>>>>>>>>
>>>>>>>>> Frankly I do not see how it can be fixed
>>>>>>>>> without any race with present HW PIR design.
>>>>>>>>
>>>>>>>> At kvm_accept_apic_interrupt, check IRR before setting PIR bit, if IRR
>>>>>>>> already set, don't set PIR.
>>>>>>>
>>>>>>> Or:
>>>>>>>
>>>>>>> apic_accept_interrupt() {
>>>>>>>
>>>>>>> 1. Read ORIG_PIR=PIR, ORIG_IRR=IRR.
>>>>>>> Never set IRR when HWAPIC enabled, even if outside of guest mode.
>>>>>>> 2. Set PIR and let HW or SW VM-entry transfer it to IRR.
>>>>>>> 3. set_irq return value: (ORIG_PIR or ORIG_IRR set).
>>>>>>> }
>>>>>>>
>>>>>>> Two or more concurrent set_irq can race with each other, though. Can
>>>>>>> either document the race or add a lock.
>>>>>> According the SDM, software should not touch the IRR when target vcpu
> is
>>>>> running. Instead, use locked way to access PIR. So your solution may
>>>>> wrong. Then your apicv patches are broken, because they do exactly
>>>>> that.
>>>> Which code is broken?
>>>>
>>> The one that updates IRR directly on the apic page.
>> No, all the updates are ensuring the target vcpu is not running. So
>> it's safe to touch IRR.
>>
> Not at all. Read the code.
Sorry. I still cannot figure out which code is wrong. All the places call sync_pir_to_irr() are on target vcpu.
Can you point out the code? Thanks.
Best regards,
Yang
--
To unsubscribe from this list: send the line "unsubscribe kvm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
