Hi Sasha, On Thu, Aug 2, 2012 at 5:29 PM, Sasha Levin <levinsasha928@xxxxxxxxx> wrote: > Use the new KVM_SIGNAL_MSI ioctl to inject interrupts directly. > > We still create GSIs and keep them for two reasons: > > - They're required by virtio-* devices. > - There's not much overhead since we just create them when starting the > guest, they don't use anything when the guest is running. > > Signed-off-by: Sasha Levin <levinsasha928@xxxxxxxxx> This patch makes 'make check' hang for me. Full boot log below: # lkvm run -k ../../arch/x86/boot/bzImage -m 448 -c 4 --name guest-27916 Decompressing Linux... Parsing ELF... done. Booting the kernel. [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.5.0+ (penberg@tux) (gcc version 4.6.3 20120306 (Red Hat 4.6.3-2) (GCC) ) #22 SMP Sat Aug 4 12:10:59 EEST 2012 [ 0.000000] Command line: noapic noacpi pci=conf1 reboot=k panic=1 i8042.direct=1 i8042.dumbkbd=1 i8042.nopnp=1 console=ttyS0 earlyprintk=serial i8042.noaux=1 init=init root=/dev/vda rw [ 0.000000] e820: BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable [ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000ffffe] reserved [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001bffffff] usable [ 0.000000] bootconsole [earlyser0] enabled [ 0.000000] NX (Execute Disable) protection: active [ 0.000000] DMI not present or invalid. [ 0.000000] No AGP bridge found [ 0.000000] e820: last_pfn = 0x1c000 max_arch_pfn = 0x400000000 [ 0.000000] x86 PAT enabled: cpu 0, old 0x70106, new 0x7010600070106 [ 0.000000] CPU MTRRs all blank - virtualized system. [ 0.000000] found SMP MP-table at [mem 0x000f0370-0x000f037f] mapped at [ffff8800000f0370] [ 0.000000] init_memory_mapping: [mem 0x00000000-0x1bffffff] [ 0.000000] ACPI Error: A valid RSDP was not found (20120320/tbxfroot-219) [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000001bffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x1bffffff] [ 0.000000] NODE_DATA [mem 0x1bffc000-0x1bffffff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x00010000-0x00ffffff] [ 0.000000] DMA32 [mem 0x01000000-0xffffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00010000-0x0009efff] [ 0.000000] node 0: [mem 0x00100000-0x1bffffff] [ 0.000000] Intel MultiProcessor Specification v1.4 [ 0.000000] MPTABLE: OEM ID: KVMCPU00 [ 0.000000] MPTABLE: Product ID: 0.1 [ 0.000000] MPTABLE: APIC at: 0xFEE00000 [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] Processor #1 [ 0.000000] Processor #2 [ 0.000000] Processor #3 [ 0.000000] IOAPIC[0]: apic_id 5, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] Processors: 4 [ 0.000000] SMP: Allowing 4 CPUs, 0 hotplug CPUs [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000 [ 0.000000] PM: Registered nosave memory: 00000000000f0000 - 00000000000ff000 [ 0.000000] PM: Registered nosave memory: 00000000000ff000 - 0000000000100000 [ 0.000000] e820: [mem 0x1c000000-0xffffffff] available for PCI devices [ 0.000000] setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 26 pages/cpu @ffff88001bc00000 s77120 r8192 d21184 u524288 [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 112777 [ 0.000000] Policy zone: DMA32 [ 0.000000] Kernel command line: noapic noacpi pci=conf1 reboot=k panic=1 i8042.direct=1 i8042.dumbkbd=1 i8042.nopnp=1 console=ttyS0 earlyprintk=serial i8042.noaux=1 init=init root=/dev/vda rw [ 0.000000] PID hash table entries: 2048 (order: 2, 16384 bytes) [ 0.000000] __ex_table already sorted, skipping sort [ 0.000000] xsave/xrstor: enabled xstate_bv 0x7, cntxt size 0x340 [ 0.000000] Checking aperture... [ 0.000000] No AGP bridge found [ 0.000000] Memory: 435020k/458752k available (7228k kernel code, 452k absent, 23280k reserved, 5730k data, 588k init) [ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:4352 nr_irqs:712 16 [ 0.000000] Console: colour *CGA 80x25 [ 0.000000] console [ttyS0] enabled, bootconsole disabled [ 0.000000] console [ttyS0] enabled, bootconsole disabled [ 0.000000] Fast TSC calibration using PIT [ 0.000000] Detected 2691.176 MHz processor. [ 0.003002] Calibrating delay loop (skipped), value calculated using timer frequency.. 5382.35 BogoMIPS (lpj=2691176) [ 0.004267] pid_max: default: 32768 minimum: 301 [ 0.004712] Security Framework initialized [ 0.005003] SELinux: Initializing. [ 0.005381] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.006208] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.007306] Mount-cache hash table entries: 256 [ 0.008012] Initializing cgroup subsys cpuacct [ 0.008433] Initializing cgroup subsys freezer [ 0.008892] CPU: Physical Processor ID: 0 [ 0.009001] CPU: Processor Core ID: 0 [ 0.009359] mce: CPU supports 32 MCE banks [ 0.010403] CPU0: Intel 06/2a stepping 07 [ 0.112030] Performance Events: unsupported p6 CPU model 42 no PMU driver, software events only. [ 0.113087] Booting Node 0, Processors #1 #2 #3 Ok. [ 0.153001] Brought up 4 CPUs [ 0.153316] Total of 4 processors activated (21529.40 BogoMIPS). [ 0.155187] kworker/u:0 (20) used greatest stack depth: 5560 bytes left [ 0.155187] RTC time: 9:14:11, date: 08/04/12 [ 0.155187] NET: Registered protocol family 16 [ 0.160055] PCI: Using configuration type 1 for base access [ 0.196037] bio: create slab <bio-0> at 0 [ 0.198008] ACPI: Interpreter disabled. [ 0.199002] vgaarb: loaded [ 0.199983] SCSI subsystem initialized [ 0.201025] usbcore: registered new interface driver usbfs [ 0.202011] usbcore: registered new interface driver hub [ 0.203014] usbcore: registered new device driver usb [ 0.205021] Advanced Linux Sound Architecture Driver Version 1.0.25. [ 0.205980] PCI: Probing PCI hardware [ 0.207032] PCI host bridge to bus 0000:00 [ 0.207984] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 0.208990] pci_bus 0000:00: root bus resource [mem 0x00000000-0xfffffffff] [ 0.213040] cfg80211: Calling CRDA to update world regulatory domain [ 0.218077] NetLabel: Initializing [ 0.218418] NetLabel: domain hash size = 128 [ 0.218418] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.218477] NetLabel: unlabeled traffic allowed by default [ 0.224031] pnp: PnP ACPI: disabled [ 0.233022] NET: Registered protocol family 2 [ 0.234012] IP route cache hash table entries: 4096 (order: 3, 32768 bytes) [ 0.234807] TCP established hash table entries: 16384 (order: 6, 262144 bytes) [ 0.235032] TCP bind hash table entries: 16384 (order: 6, 262144 bytes) [ 0.236030] TCP: Hash tables configured (established 16384 bind 16384) [ 0.236976] TCP: reno registered [ 0.237290] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.237982] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.238656] NET: Registered protocol family 1 [ 0.239049] RPC: Registered named UNIX socket transport module. [ 0.239975] RPC: Registered udp transport module. [ 0.240425] RPC: Registered tcp transport module. [ 0.240974] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.241756] platform rtc_cmos: registered platform RTC device (no PNP device found) [ 0.245007] microcode: CPU0 sig=0x206a7, pf=0x1, revision=0x1 [ 0.245007] microcode: CPU1 sig=0x206a7, pf=0x1, revision=0x1 [ 0.245975] microcode: CPU2 sig=0x206a7, pf=0x1, revision=0x1 [ 0.246974] microcode: CPU3 sig=0x206a7, pf=0x1, revision=0x1 [ 0.248310] microcode: Microcode Update Driver: v2.00 <tigran@xxxxxxxxxxxxxxxxxxxx>, Peter Oruba [ 0.249974] audit: initializing netlink socket (disabled) [ 0.250500] type=2000 audit(4499745251.249:1): initialized [ 0.266041] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 0.274081] VFS: Disk quotas dquot_6.5.2 [ 0.275003] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.278011] NFS: Registering the id_resolver key type [ 0.278987] Key type id_resolver registered [ 0.280046] 9p: Installing v9fs 9p2000 file system support [ 0.281980] msgmni has been set to 849 [ 0.284002] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.284969] io scheduler noop registered [ 0.285968] io scheduler deadline registered [ 0.286978] io scheduler cfq registered (default) [ 0.287969] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.288531] virtio-pci 0000:00:01.0: enabling device (0000 -> 0003) [ 0.289056] virtio-pci 0000:00:02.0: enabling device (0000 -> 0003) [ 0.291079] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled ÿ[ 0.538076] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a U6_16550A ÿ[ 0.785054] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a U6_16550A ÿ[ 1.031999] serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a U6_16550A [ 1.033890] Non-volatile memory driver v1.3 [ 1.034855] Linux agpgart interface v0.103 [ 1.035895] [drm] Initialized drm 1.1.0 20060810 [ 1.036351] [drm:i915_init] *ERROR* drm/i915 can't work without intel_agp module! [ 1.040917] brd: module loaded [ 1.043922] loop: module loaded [ 1.243831] Switching to clocksource tsc -- To unsubscribe from this list: send the line "unsubscribe kvm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
