Hi All, I noticed that the PCI registers are not all mapped to the guest for a PCI pass through device. For example, I was trying to pass through a PCI function (NIC) to a guest and in the guest the MSI-X table offset register is not mapped properly. It was showing all 0s. This is in RHEL 6.0 beta and the guest was a SLES11 64 bit. In the RHEL 6.0 host I see following for the PCI function: --------- 05:00.0 Ethernet controller: QLogic Corp. cLOM8214 1/10GbE Controller (rev 54) Subsystem: QLogic Corp. 8200 Series Dual Port 10GbE Converged Network Adapter (TCP/IP Networking) Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 74 Region 0: Memory at df200000 (64-bit, non-prefetchable) [size=2M] Region 4: Memory at df1b0000 (64-bit, non-prefetchable) [size=64K] Expansion ROM at df1c0000 [disabled] [size=256K] Capabilities: [40] MSI-X: Enable- Count=32 Masked- Vector table: BAR=0 offset=00090000 PBA: BAR=0 offset=00090800 ... Kernel driver in use: pci-stub 00: 77 10 20 80 42 05 10 00 54 00 00 02 40 00 80 00 10: 04 00 20 df 00 00 00 00 00 00 00 00 00 00 00 00 20: 04 00 1b df 00 00 00 00 00 00 00 00 77 10 07 02 30: 00 00 1c df 40 00 00 00 00 00 00 00 0a 01 00 00 40: 11 80 1f 00 00 00 09 00 00 08 09 00 00 00 00 00 ---------- And in the SLES11 guest, I see following for the same function: ------------ 00:07.0 Ethernet controller: QLogic Corp. Device 8020 (rev 54) Subsystem: QLogic Corp. Device 0207 Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 11 Region 0: Memory at f2200000 (32-bit, non-prefetchable) [size=2M] Region 4: Memory at f2400000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at f2440000 [disabled] [size=256K] Capabilities: [40] Message Signalled Interrupts: Mask- 64bit- Count=1/1 Enable- Address: 00000000 Data: 0000 Capabilities: [50] MSI-X: Enable- Mask- TabSize=32 Vector table: BAR=0 offset=00090000 PBA: BAR=0 offset=00000000 00: 77 10 20 80 42 05 10 00 54 00 00 02 40 00 80 00 10: 00 00 20 f2 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 40 f2 00 00 00 00 00 00 00 00 77 10 07 02 30: 08 00 44 f2 40 00 00 00 00 00 00 00 0b 01 00 00 40: 05 50 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ------------ Note that the data at byte offset 40h is different for the host and the guest. Is this expected or is it a bug in KVM? Is there any spec out there that specifies what PCI registers are accessible from guest and how much of the PCI config space is mapped to the guest? This is helpful to know, especially in the context of SR-IOV. If a VF is pass throughed to a guest, are all the VF registers visible in host system will be mapped (and accessible) to the guest OS? thanks much, Anirban-- To unsubscribe from this list: send the line "unsubscribe kvm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
