Re: [RFC PATCH 0/4] Implement multiqueue virtio-net

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, Sep 09, 2010 at 03:15:53PM +0530, Krishna Kumar2 wrote:
> > Krishna Kumar2/India/IBM wrote on 09/08/2010 10:17:49 PM:
> 
> Some more results and likely cause for single netperf
> degradation below.
> 
> 
> > Guest -> Host (single netperf):
> > I am getting a drop of almost 20%. I am trying to figure out
> > why.
> >
> > Host -> guest (single netperf):
> > I am getting an improvement of almost 15%. Again - unexpected.
> >
> > Guest -> Host TCP_RR: I get an average 7.4% increase in #packets
> > for runs upto 128 sessions. With fewer netperf (under 8), there
> > was a drop of 3-7% in #packets, but beyond that, the #packets
> > improved significantly to give an average improvement of 7.4%.
> >
> > So it seems that fewer sessions is having negative effect for
> > some reason on the tx side. The code path in virtio-net has not
> > changed much, so the drop in some cases is quite unexpected.
> 
> The drop for the single netperf seems to be due to multiple vhost.
> I changed the patch to start *single* vhost:
> 
> Guest -> Host (1 netperf, 64K): BW: 10.79%, SD: -1.45%
> Guest -> Host (1 netperf)     : Latency: -3%, SD: 3.5%
> 
> Single vhost performs well but hits the barrier at 16 netperf
> sessions:
> 
> SINGLE vhost (Guest -> Host):
> 	1 netperf:    BW: 10.7%     SD: -1.4%
> 	4 netperfs:   BW: 3%        SD: 1.4%
> 	8 netperfs:   BW: 17.7%     SD: -10%
>       16 netperfs:  BW: 4.7%      SD: -7.0%
>       32 netperfs:  BW: -6.1%     SD: -5.7%
> BW and SD both improves (guest multiple txqs help). For 32
> netperfs, SD improves.
> 
> But with multiple vhosts, guest is able to send more packets
> and BW increases much more (SD too increases, but I think
> that is expected).

Why is this expected?

> From the earlier results:
> 
> N#      BW1     BW2    (%)      SD1     SD2    (%)      RSD1    RSD2    (%)
> _______________________________________________________________________________
> 4       26387   40716 (54.30)   20      28   (40.00)    86      85
> (-1.16)
> 8       24356   41843 (71.79)   88      129  (46.59)    372     362
> (-2.68)
> 16      23587   40546 (71.89)   375     564  (50.40)    1558    1519
> (-2.50)
> 32      22927   39490 (72.24)   1617    2171 (34.26)    6694    5722
> (-14.52)
> 48      23067   39238 (70.10)   3931    5170 (31.51)    15823   13552
> (-14.35)
> 64      22927   38750 (69.01)   7142    9914 (38.81)    28972   26173
> (-9.66)
> 96      22568   38520 (70.68)   16258   27844 (71.26)   65944   73031
> (10.74)
> _______________________________________________________________________________
> (All tests were done without any tuning)
> 
> >From my testing:
> 
> 1. Single vhost improves mq guest performance upto 16
>    netperfs but degrades after that.
> 2. Multiple vhost degrades single netperf guest
>    performance, but significantly improves performance
>    for any number of netperf sessions.
> 
> Likely cause for the 1 stream degradation with multiple
> vhost patch:
> 
> 1. Two vhosts run handling the RX and TX respectively.
>    I think the issue is related to cache ping-pong esp
>    since these run on different cpus/sockets.

Right. With TCP I think we are better off handling
TX and RX for a socket by the same vhost, so that
packet and its ack are handled by the same thread.
Is this what happens with RX multiqueue patch?
How do we select an RX queue to put the packet on?


> 2. I (re-)modified the patch to share RX with TX[0]. The
>    performance drop is the same, but the reason is the
>    guest is not using txq[0] in most cases (dev_pick_tx),
>    so vhost's rx and tx are running on different threads.
>    But whenever the guest uses txq[0], only one vhost
>    runs and the performance is similar to original.
> 
> I went back to my *submitted* patch and started a guest
> with numtxq=16 and pinned every vhost to cpus #0&1. Now
> whether guest used txq[0] or txq[n], the performance is
> similar or better (between 10-27% across 10 runs) than
> original code. Also, -6% to -24% improvement in SD.
> 
> I will start a full test run of original vs submitted
> code with minimal tuning (Avi also suggested the same),
> and re-send. Please let me know if you need any other
> data.
> 
> Thanks,
> 
> - KK
--
To unsubscribe from this list: send the line "unsubscribe kvm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [KVM ARM]     [KVM ia64]     [KVM ppc]     [Virtualization Tools]     [Spice Development]     [Libvirt]     [Libvirt Users]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite Questions]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux