Re: [PATCH Part1 RFC v4 08/36] x86/sev: check the vmpl level

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 8/13/21 2:25 AM, Borislav Petkov wrote:
> On Wed, Jul 07, 2021 at 01:14:38PM -0500, Brijesh Singh wrote:
>> Virtual Machine Privilege Level (VMPL) is an optional feature in the
>> SEV-SNP architecture, which allows a guest VM to divide its address space
>> into four levels. The level can be used to provide the hardware isolated
>> abstraction layers with a VM. The VMPL0 is the highest privilege, and
>> VMPL3 is the least privilege. Certain operations must be done by the VMPL0
>> software, such as:
>>
>> * Validate or invalidate memory range (PVALIDATE instruction)
>> * Allocate VMSA page (RMPADJUST instruction when VMSA=1)
>>
>> The initial SEV-SNP support assumes that the guest kernel is running on
>> VMPL0. Let's add a check to make sure that kernel is running at VMPL0
>> before continuing the boot. There is no easy method to query the current
>> VMPL level, so use the RMPADJUST instruction to determine whether its
>> booted at the VMPL0.
>>
>> Signed-off-by: Brijesh Singh <brijesh.singh@xxxxxxx>
>> ---
>>  arch/x86/boot/compressed/sev.c    | 41 ++++++++++++++++++++++++++++---
>>  arch/x86/include/asm/sev-common.h |  1 +
>>  arch/x86/include/asm/sev.h        |  3 +++
>>  3 files changed, 42 insertions(+), 3 deletions(-)
>>
>> diff --git a/arch/x86/boot/compressed/sev.c b/arch/x86/boot/compressed/sev.c
>> index 7be325d9b09f..2f3081e9c78c 100644
>> --- a/arch/x86/boot/compressed/sev.c
>> +++ b/arch/x86/boot/compressed/sev.c
>> @@ -134,6 +134,36 @@ static inline bool sev_snp_enabled(void)
>>  	return msr_sev_status & MSR_AMD64_SEV_SNP_ENABLED;
>>  }
>>  
>> +static bool is_vmpl0(void)
>> +{
>> +	u64 attrs, va;
>> +	int err;
>> +
>> +	/*
>> +	 * There is no straightforward way to query the current VMPL level. The
> So this is not nice at all.
>
> And this VMPL level checking can't be part of the GHCB MSR protocol
> because the HV can tell us any VPML level it wants to.
>
> Is there a way to disable VMPL levels and say, this guest should run
> only at VMPL0?

No.

>
> Err, I see SYSCFG[VMPLEn]:
>
> "VMPLEn. Bit 25. Setting this bit to 1 enables the VMPL feature (Section
> 15.36.7 “Virtual Machine Privilege Levels,” on page 580). Software
> should set this bit to 1 when SecureNestedPagingEn is being set to 1.
> Once SecureNestedPagingEn is set to 1, VMPLEn cannot be changed."
>
> But why should that bit be set if SNP is enabled? Can I run a SNP guest
> without VPMLs, i.e, at an implicit VPML level 0?

During the firmware initialization the PSP requires that the VMPLEn is
set. See SNP firmware spec [1] section 8.6. To run the SNP guest you
*must* specify a VMPL level during the vCPU creation.


>
> It says above VPML is optional...

I should not say its optional when we know from the SEV-SNP spec that
VMPLEn must be set to launch SEV-SNP guest. I will fix the description.


> Also, why do you even need to do this at all since the guest controls
> and validates its memory with the RMP? It can simply go and check the
> VMPLs of every page it owns to make sure it is 0.

There is no easy way for a guest to query its VMPL level. The VMPL level
is set during the vCPU creation. The boot cpu is created by the HV and
thus its VMPL level is set by the HV. If HV chooses a lower VMPL level
for the boot CPU then Linux guest will not be able to validate its
memory because the PVALIDATE instruction will cause #GP when the vCPU is
running at !VMPL0. The patch tries to detect the boot CPU VMPL level and
terminate the boot.


>
> Also, if you really wanna support guests with multiple VMPLs, then
> prevalidating its memory is going to be a useless exercise because it'll
> have to go and revalidate the VMPL levels...

We do not need to re-valiate memory when changing to different VMPL
level. The RMPADJUST instruction inside the guest can be used to change
the VMPL permission.


> I also see this:
>
> "When the hypervisor assigns a page to a guest using RMPUPDATE, full
> permissions are enabled for VMPL0 and are disabled for all other VMPLs."
>
> so you get your memory at VMPL0 by the HV. So what is that check for?

Validating the memory is a two step process:

#1 HV adding the memory using the RMPUPDATE in the RMP table.

#2 Guest issuing the PVALIDATE

If guest is not running at VMPL0 then step #2 will cause #GP.  The check
is prevent the #GP and terminate the boot early.

thanks




[Index of Archives]     [KVM ARM]     [KVM ia64]     [KVM ppc]     [Virtualization Tools]     [Spice Development]     [Libvirt]     [Libvirt Users]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite Questions]     [Linux Kernel]     [Linux SCSI]     [XFree86]

  Powered by Linux