Re: [PATCH] [RESEND] KVM:VMX: Add support for Pause-Loop Exiting

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Avi,

hrtimer is used for sleep in attached patch, which have similar perf gain with previous one. Maybe we can check in this patch first, and turn to direct yield in future, as you suggested.

Thanks,
edwin

Avi Kivity wrote:
On 09/23/2009 05:04 PM, Zhai, Edwin wrote:
Avi,

This is the patch to enable PLE, which depends on the a small change of Linux scheduler
(see http://lkml.org/lkml/2009/5/20/447).

According to our discussion last time, one missing part is that if PLE
exit, pick up an unscheduled vcpu at random and schedule it. But
further investigation found that:
1. KVM is hard to know the schedule state for each vcpu.
2. Linux scheduler has no existed API can be used to pull a specific
task to this cpu, so we need more changes to the common scheduler.
So I prefer current simple way: just give up current cpu time.

If no objection, I'll try to push common scheduler change first to
linux.

We haven't sorted out what is the correct thing to do here. I think we should go for a directed yield, but until we have it, you can use hrtimers to sleep for 100 microseconds and hope the holding vcpu will get scheduled. Even if it doesn't, we're only wasting a few percent cpu time instead of spinning.


--
best rgds,
edwin

KVM:VMX: Add support for Pause-Loop Exiting

New NHM processors will support Pause-Loop Exiting by adding 2 VM-execution
control fields:
PLE_Gap    - upper bound on the amount of time between two successive
             executions of PAUSE in a loop.
PLE_Window - upper bound on the amount of time a guest is allowed to execute in
             a PAUSE loop

If the time, between this execution of PAUSE and previous one, exceeds the
PLE_Gap, processor consider this PAUSE belongs to a new loop.
Otherwise, processor determins the the total execution time of this loop(since
1st PAUSE in this loop), and triggers a VM exit if total time exceeds the
PLE_Window.
* Refer SDM volume 3b section 21.6.13 & 22.1.3.

Pause-Loop Exiting can be used to detect Lock-Holder Preemption, where one VP
is sched-out after hold a spinlock, then other VPs for same lock are sched-in
to waste the CPU time.

Our tests indicate that most spinlocks are held for less than 212 cycles.
Performance tests show that with 2X LP over-commitment we can get +2% perf
improvement for kernel build(Even more perf gain with more LPs).

Signed-off-by: Zhai Edwin <edwin.zhai@xxxxxxxxx>

diff --git a/arch/x86/include/asm/vmx.h b/arch/x86/include/asm/vmx.h
index 272514c..2b49454 100644
--- a/arch/x86/include/asm/vmx.h
+++ b/arch/x86/include/asm/vmx.h
@@ -56,6 +56,7 @@
 #define SECONDARY_EXEC_ENABLE_VPID              0x00000020
 #define SECONDARY_EXEC_WBINVD_EXITING		0x00000040
 #define SECONDARY_EXEC_UNRESTRICTED_GUEST	0x00000080
+#define SECONDARY_EXEC_PAUSE_LOOP_EXITING	0x00000400
 
 
 #define PIN_BASED_EXT_INTR_MASK                 0x00000001
@@ -144,6 +145,8 @@ enum vmcs_field {
 	VM_ENTRY_INSTRUCTION_LEN        = 0x0000401a,
 	TPR_THRESHOLD                   = 0x0000401c,
 	SECONDARY_VM_EXEC_CONTROL       = 0x0000401e,
+	PLE_GAP                         = 0x00004020,
+	PLE_WINDOW                      = 0x00004022,
 	VM_INSTRUCTION_ERROR            = 0x00004400,
 	VM_EXIT_REASON                  = 0x00004402,
 	VM_EXIT_INTR_INFO               = 0x00004404,
@@ -248,6 +251,7 @@ enum vmcs_field {
 #define EXIT_REASON_MSR_READ            31
 #define EXIT_REASON_MSR_WRITE           32
 #define EXIT_REASON_MWAIT_INSTRUCTION   36
+#define EXIT_REASON_PAUSE_INSTRUCTION   40
 #define EXIT_REASON_MCE_DURING_VMENTRY	 41
 #define EXIT_REASON_TPR_BELOW_THRESHOLD 43
 #define EXIT_REASON_APIC_ACCESS         44
diff --git a/arch/x86/kvm/vmx.c b/arch/x86/kvm/vmx.c
index 3fe0d42..21dbfe9 100644
--- a/arch/x86/kvm/vmx.c
+++ b/arch/x86/kvm/vmx.c
@@ -61,6 +61,25 @@ module_param_named(unrestricted_guest,
 static int __read_mostly emulate_invalid_guest_state = 0;
 module_param(emulate_invalid_guest_state, bool, S_IRUGO);
 
+/*
+ * These 2 parameters are used to config the controls for Pause-Loop Exiting:
+ * ple_gap:    upper bound on the amount of time between two successive
+ *             executions of PAUSE in a loop. Also indicate if ple enabled.
+ *             According to test, this time is usually small than 41 cycles.
+ * ple_window: upper bound on the amount of time a guest is allowed to execute
+ *             in a PAUSE loop. Tests indicate that most spinlocks are held for
+ *             less than 2^12 cycles
+ * Time is measured based on a counter that runs at the same rate as the TSC,
+ * refer SDM volume 3b section 21.6.13 & 22.1.3.
+ */
+#define KVM_VMX_DEFAULT_PLE_GAP    41
+#define KVM_VMX_DEFAULT_PLE_WINDOW 4096
+static int __read_mostly ple_gap = KVM_VMX_DEFAULT_PLE_GAP;
+module_param(ple_gap, int, S_IRUGO);
+
+static int __read_mostly ple_window = KVM_VMX_DEFAULT_PLE_WINDOW;
+module_param(ple_window, int, S_IRUGO);
+
 struct vmcs {
 	u32 revision_id;
 	u32 abort;
@@ -319,6 +338,12 @@ static inline int cpu_has_vmx_unrestricted_guest(void)
 		SECONDARY_EXEC_UNRESTRICTED_GUEST;
 }
 
+static inline int cpu_has_vmx_ple(void)
+{
+	return vmcs_config.cpu_based_2nd_exec_ctrl &
+		SECONDARY_EXEC_PAUSE_LOOP_EXITING;
+}
+
 static inline int vm_need_virtualize_apic_accesses(struct kvm *kvm)
 {
 	return flexpriority_enabled &&
@@ -1256,7 +1281,8 @@ static __init int setup_vmcs_config(struct vmcs_config *vmcs_conf)
 			SECONDARY_EXEC_WBINVD_EXITING |
 			SECONDARY_EXEC_ENABLE_VPID |
 			SECONDARY_EXEC_ENABLE_EPT |
-			SECONDARY_EXEC_UNRESTRICTED_GUEST;
+			SECONDARY_EXEC_UNRESTRICTED_GUEST |
+			SECONDARY_EXEC_PAUSE_LOOP_EXITING;
 		if (adjust_vmx_controls(min2, opt2,
 					MSR_IA32_VMX_PROCBASED_CTLS2,
 					&_cpu_based_2nd_exec_control) < 0)
@@ -1400,6 +1426,9 @@ static __init int hardware_setup(void)
 	if (enable_ept && !cpu_has_vmx_ept_2m_page())
 		kvm_disable_largepages();
 
+	if (!cpu_has_vmx_ple())
+		ple_gap = 0;
+
 	return alloc_kvm_area();
 }
 
@@ -2312,9 +2341,16 @@ static int vmx_vcpu_setup(struct vcpu_vmx *vmx)
 			exec_control &= ~SECONDARY_EXEC_ENABLE_EPT;
 		if (!enable_unrestricted_guest)
 			exec_control &= ~SECONDARY_EXEC_UNRESTRICTED_GUEST;
+		if (!ple_gap)
+			exec_control &= ~SECONDARY_EXEC_PAUSE_LOOP_EXITING;
 		vmcs_write32(SECONDARY_VM_EXEC_CONTROL, exec_control);
 	}
 
+	if (ple_gap) {
+		vmcs_write32(PLE_GAP, ple_gap);
+		vmcs_write32(PLE_WINDOW, ple_window);
+	}
+
 	vmcs_write32(PAGE_FAULT_ERROR_CODE_MASK, !!bypass_guest_pf);
 	vmcs_write32(PAGE_FAULT_ERROR_CODE_MATCH, !!bypass_guest_pf);
 	vmcs_write32(CR3_TARGET_COUNT, 0);           /* 22.2.1 */
@@ -3362,6 +3398,24 @@ out:
 }
 
 /*
+ * Indicate a busy-waiting vcpu in spinlock. We do not enable the PAUSE
+ * exiting, so only get here on cpu with PAUSE-Loop-Exiting.
+ */
+static int handle_pause(struct kvm_vcpu *vcpu,
+				struct kvm_run *kvm_run)
+{
+	ktime_t expires;
+	skip_emulated_instruction(vcpu);
+
+	/* Sleep for 1 msec, and hope lock-holder got scheduled */
+	expires = ktime_add_ns(ktime_get(), 1000000UL);
+	set_current_state(TASK_INTERRUPTIBLE);
+	schedule_hrtimeout(&expires, HRTIMER_MODE_ABS);
+
+	return 1;
+}
+
+/*
  * The exit handlers return 1 if the exit was handled fully and guest execution
  * may resume.  Otherwise they set the kvm_run parameter to indicate what needs
  * to be done to userspace and return 0.
@@ -3397,6 +3451,7 @@ static int (*kvm_vmx_exit_handlers[])(struct kvm_vcpu *vcpu) = {
 	[EXIT_REASON_MCE_DURING_VMENTRY]      = handle_machine_check,
 	[EXIT_REASON_EPT_VIOLATION]	      = handle_ept_violation,
 	[EXIT_REASON_EPT_MISCONFIG]           = handle_ept_misconfig,
+	[EXIT_REASON_PAUSE_INSTRUCTION]       = handle_pause,
 };
 
 static const int kvm_vmx_max_exit_handlers =

[Index of Archives]     [KVM ARM]     [KVM ia64]     [KVM ppc]     [Virtualization Tools]     [Spice Development]     [Libvirt]     [Libvirt Users]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite Questions]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux