Re: [RFC PATCH 00/27] vDPA software assisted live migration

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



----- Original Message -----
> On Fri, Nov 20, 2020 at 07:50:38PM +0100, Eugenio Pérez wrote:
> > This series enable vDPA software assisted live migration for vhost-net
> > devices. This is a new method of vhost devices migration: Instead of
> > relay on vDPA device's dirty logging capability, SW assisted LM
> > intercepts dataplane, forwarding the descriptors between VM and device.
> 
> Pros:
> + vhost/vDPA devices don't need to implement dirty memory logging
> + Obsoletes ioctl(VHOST_SET_LOG_BASE) and friends
> 
> Cons:
> - Not generic, relies on vhost-net-specific ioctls
> - Doesn't support VIRTIO Shared Memory Regions
>   https://github.com/oasis-tcs/virtio-spec/blob/master/shared-mem.tex

I may miss something but my understanding is that it's the
responsiblity of device to migrate this part?

> - Performance (see below)
> 
> I think performance will be significantly lower when the shadow vq is
> enabled. Imagine a vDPA device with hardware vq doorbell registers
> mapped into the guest so the guest driver can directly kick the device.
> When the shadow vq is enabled a vmexit is needed to write to the shadow
> vq ioeventfd, then the host kernel scheduler switches to a QEMU thread
> to read the ioeventfd, the descriptors are translated, QEMU writes to
> the vhost hdev kick fd, the host kernel scheduler switches to the vhost
> worker thread, vhost/vDPA notifies the virtqueue, and finally the
> vDPA driver writes to the hardware vq doorbell register. That is a lot
> of overhead compared to writing to an exitless MMIO register!

I think it's a balance. E.g we can poll the virtqueue to have an
exitless doorbell.

> 
> If the shadow vq was implemented in drivers/vhost/ and QEMU used the
> existing ioctl(VHOST_SET_LOG_BASE) approach, then the overhead would be
> reduced to just one set of ioeventfd/irqfd. In other words, the QEMU
> dirty memory logging happens asynchronously and isn't in the dataplane.
> 
> In addition, hardware that supports dirty memory logging as well as
> software vDPA devices could completely eliminate the shadow vq for even
> better performance.

Yes. That's our plan. But the interface might require more thought.

E.g is the bitmap a good approach? To me reporting dirty pages via
virqueue is better since it get less footprint and is self throttled.

And we need an address space other than the one used by guest for
either bitmap for virtqueue.

> 
> But performance is a question of "is it good enough?". Maybe this
> approach is okay and users don't expect good performance while dirty
> memory logging is enabled.

Yes, and actually such slow down may help for the converge of the
migration.

Note that the whole idea is try to have a generic solution for all
types of devices. It's good to consider the performance but for the
first stage, it should be sufficient to make it work and consider to
optimize on top.

> I just wanted to share the idea of moving the
> shadow vq into the kernel in case you like that approach better.

My understanding is to keep kernel as simple as possible and leave the
polices to userspace as much as possible. E.g it requires us to
disable doorbell mapping and irq offloading, all of which were under
the control of userspace.

Thanks

> 
> Stefan
>






[Index of Archives]     [KVM ARM]     [KVM ia64]     [KVM ppc]     [Virtualization Tools]     [Spice Development]     [Libvirt]     [Libvirt Users]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite Questions]     [Linux Kernel]     [Linux SCSI]     [XFree86]

  Powered by Linux