On 11/13/2019 11:57 PM, Alex Williamson wrote:
On Wed, 13 Nov 2019 11:24:17 +0100
Cornelia Huck <cohuck@xxxxxxxxxx> wrote:
On Tue, 12 Nov 2019 15:30:05 -0700
Alex Williamson <alex.williamson@xxxxxxxxxx> wrote:
On Tue, 12 Nov 2019 22:33:36 +0530
Kirti Wankhede <kwankhede@xxxxxxxxxx> wrote:
- Defined MIGRATION region type and sub-type.
- Used 3 bits to define VFIO device states.
Bit 0 => _RUNNING
Bit 1 => _SAVING
Bit 2 => _RESUMING
Combination of these bits defines VFIO device's state during migration
_RUNNING => Normal VFIO device running state. When its reset, it
indicates _STOPPED state. when device is changed to
_STOPPED, driver should stop device before write()
returns.
_SAVING | _RUNNING => vCPUs are running, VFIO device is running but
start saving state of device i.e. pre-copy state
_SAVING => vCPUs are stopped, VFIO device should be stopped, and
s/should/must/
save device state,i.e. stop-n-copy state
_RESUMING => VFIO device resuming state.
_SAVING | _RESUMING and _RUNNING | _RESUMING => Invalid states
A table might be useful here and in the uapi header to indicate valid
states:
I like that.
| _RESUMING | _SAVING | _RUNNING | Description
+-----------+---------+----------+------------------------------------------
| 0 | 0 | 0 | Stopped, not saving or resuming (a)
+-----------+---------+----------+------------------------------------------
| 0 | 0 | 1 | Running, default state
+-----------+---------+----------+------------------------------------------
| 0 | 1 | 0 | Stopped, migration interface in save mode
+-----------+---------+----------+------------------------------------------
| 0 | 1 | 1 | Running, save mode interface, iterative
+-----------+---------+----------+------------------------------------------
| 1 | 0 | 0 | Stopped, migration resume interface active
+-----------+---------+----------+------------------------------------------
| 1 | 0 | 1 | Invalid (b)
+-----------+---------+----------+------------------------------------------
| 1 | 1 | 0 | Invalid (c)
+-----------+---------+----------+------------------------------------------
| 1 | 1 | 1 | Invalid (d)
I think we need to consider whether we define (a) as generally
available, for instance we might want to use it for diagnostics or a
fatal error condition outside of migration.
Are there hidden assumptions between state transitions here or are
there specific next possible state diagrams that we need to include as
well?
Some kind of state-change diagram might be useful in addition to the
textual description anyway. Let me try, just to make sure I understand
this correctly:
During User application initialization, there is one more state change:
0) 0/0/0 ---- stop to running -----> 0/0/1
1) 0/0/1 ---(trigger driver to start gathering state info)---> 0/1/1
not just gathering state info, but also copy device state to be
transferred during pre-copy phase.
Below 2 state are not just to tell driver to stop, those 2 differ.
2) is device state changed from running to stop, this is when VM
shutdowns cleanly, no need to save device state
2) 0/0/1 ---(tell driver to stop)---> 0/0/0
3) 0/1/1 ---(tell driver to stop)---> 0/1/0
above is transition from pre-copy phase to stop-and-copy phase, where
device data should be made available to user to transfer to destination
or to save it to file in case of save VM or suspend.
4) 0/0/1 ---(tell driver to resume with provided info)---> 1/0/0
I think this is to switch into resuming mode, the data will follow >
5) 1/0/0 ---(driver is ready)---> 0/0/1
6) 0/1/1 ---(tell driver to stop saving)---> 0/0/1
above can occur on migration cancelled or failed.
I think also:
0/0/1 --> 0/1/0 If user chooses to go directly to stop and copy
that's right, this happens in case of save VM or suspend VM.
0/0/0 and 0/0/1 should be reachable from any state, though I could see
that a vendor driver could fail transition from 1/0/0 -> 0/0/1 if the
received state is incomplete. Somehow though a user always needs to
return the device to the initial state, so how does device_state
interact with the reset ioctl? Would this automatically manipulate
device_state back to 0/0/1?
why would reset occur on 1/0/0 -> 0/0/1 failure?
1/0/0 -> 0/0/1 fails, then user should convey that to source that
migration has failed, then resume at source.
Not sure about the usefulness of 2).
I explained this above.
Also, is 4) the only way to
trigger resuming?
Yes.
And is the change in 5) performed by the driver, or
by userspace?
By userspace.
Are any other state transitions valid?
(...)
+ * Sequence to be followed for _SAVING|_RUNNING device state or pre-copy phase
+ * and for _SAVING device state or stop-and-copy phase:
+ * a. read pending_bytes. If pending_bytes > 0, go through below steps.
+ * b. read data_offset, indicates kernel driver to write data to staging buffer.
+ * Kernel driver should return this read operation only after writing data to
+ * staging buffer is done.
"staging buffer" implies a vendor driver implementation, perhaps we
could just state that data is available from (region + data_offset) to
(region + data_offset + data_size) upon return of this read operation.
+ * c. read data_size, amount of data in bytes written by vendor driver in
+ * migration region.
+ * d. read data_size bytes of data from data_offset in the migration region.
+ * e. process data.
+ * f. Loop through a to e. Next read on pending_bytes indicates that read data
+ * operation from migration region for previous iteration is done.
I think this indicate that step (f) should be to read pending_bytes, the
read sequence is not complete until this step. Optionally the user can
then proceed to step (b). There are no read side-effects of (a) afaict.
Is the use required to reach pending_bytes == 0 before changing
device_state, particularly transitioning to !_RUNNING? Presumably the
user can exit this sequence at any time by clearing _SAVING.
That would be transition 6) above (abort saving and continue). I think
it makes sense not to forbid this.
+ *
+ * Sequence to be followed while _RESUMING device state:
+ * While data for this device is available, repeat below steps:
+ * a. read data_offset from where user application should write data.
+ * b. write data of data_size to migration region from data_offset.
+ * c. write data_size which indicates vendor driver that data is written in
+ * staging buffer. Vendor driver should read this data from migration
+ * region and resume device's state.
The device defaults to _RUNNING state, so a prerequisite is to set
_RESUMING and clear _RUNNING, right?
Sorry, I replied yes in my previous reply, but no. Default device state
is _STOPPED. During resume _STOPPED -> _RESUMING
Transition 4) above. Do we need
I think, its not required.
7) 0/0/0 ---(tell driver to resume with provided info)---> 1/0/0
as well? (Probably depends on how sensible the 0/0/0 state is.)
I think we must unless we require the user to transition from 0/0/1 to
1/0/0 in a single operation, but I'd prefer to make 0/0/0 generally
available. Thanks,
its 0/0/0 -> 1/0/0 while resuming.
Thanks,
Kirti
Alex
