Hi Marc,
Adding a new lpi to lpi_list, the contents of the caches will not be
updated immediately until the irq is injected.
Irq's reference count will be increased when synchronized to each cache,
and reduced after deleting from each cache. Only when irq is removed
from all caches, the reference count is reduced to 0, which is allowed
to be removed from lpi_list.
So I think that the reference count of IRQ can guarantee the consistency
of lpi_list and cache, is right?
When multiple CPUs inject different lpi interrupts at the same time,
which may result in different sorts of interrupts in different caches,
even some interrupts of a certain cache are overflowed.
Eg:
The contents of the cache at a certain moment：
cache 0: c->b->a
cache 1: a->b->c
Then, inject two interrupts "d,e" simultaneously, the following results
may occur:
cache 0: e->d->c
cache 1: d->e->a
But this is no problem, just make sure that the irq found is correct.
In addition, about Locking order:
kvm->lock (mutex)
its->cmd_lock (mutex)
its->its_lock (mutex)
vgic_cpu->ap_list_lock
cache->lpi_cache_lock /**/
kvm->lpi_list_lock
vgic_irq->irq_lock
Thanks,
Xiangyou.
On 2019/7/26 21:02, Marc Zyngier wrote:
On Fri, 26 Jul 2019 13:35:20 +0100,
Xiangyou Xie <xiexiangyou@xxxxxxxxxx> wrote:
Hi Marc,
Sorry, the test data was not posted in the previous email.
I tested the impact of virtual interrupt injection time-consuming：
Run the iperf command to send UDP packets to the VM:
iperf -c $IP -u -b 40m -l 64 -t 6000&
The vm just receive UDP traffic. When configure multiple NICs, each
NIC receives the above iperf UDP traffic, This may reflect the
performance impact of shared resource competition, such as lock.
Observing the delay of virtual interrupt injection: the time spent by
the "irqfd_wakeup", "irqfd_inject" function, and kworker context
switch.
The less the better.
ITS translation cache greatly reduces the delay of interrupt injection
compared to kworker thread, because it eliminate wakeup and uncertain
scheduling delay:
kworker ITS translation cache improved
1 NIC 6.692 us 1.766 us
73.6%
10 NICs 7.536 us 2.574 us
65.8%
OK, that's pretty interesting. It would have been good to post such
data in reply to the ITS cache series.
Increases the number of lpi_translation_cache reduce lock competition.
Multi-interrupt concurrent injections perform better:
ITS translation cache with patch improved
1 NIC 1.766 us 1.694 us 4.1%
10 NICs 2.574 us 1.848 us 28.2%
That's sort off interesting too, but it doesn't answer any of the
questions I had in response to your patch: How do you ensure mutual
exclusion with the LPI list being concurrently updated? How does the
new locking fit in the current locking scheme?
Thanks,
M.
Regards,
Xiangyou
On 2019/7/24 19:09, Marc Zyngier wrote:
Hi Xiangyou,
On 24/07/2019 10:04, Xiangyou Xie wrote:
Because dist->lpi_list_lock is a perVM lock, when a virtual machine
is configured with multiple virtual NIC devices and receives
network packets at the same time, dist->lpi_list_lock will become
a performance bottleneck.
I'm sorry, but you'll have to show me some real numbers before I
consider any of this. There is a reason why the original series still
isn't in mainline, and that's because people don't post any numbers.
Adding more patches is not going to change that small fact.
This patch increases the number of lpi_translation_cache to eight,
hashes the cpuid that executes irqfd_wakeup, and chooses which
lpi_translation_cache to use.
So you've now switched to a per-cache lock, meaning that the rest of the
ITS code can manipulate the the lpi_list without synchronization with
the caches. Have you worked out all the possible races? Also, how does
this new lock class fits in the whole locking hierarchy?
If you want something that is actually scalable, do it the right way.
Use a better data structure than a list, switch to using RCU rather than
the current locking strategy. But your current approach looks quite fragile.
Thanks,
M.
