MRRS defines the maximum read request size a device is allowed to
make. Drivers will often increase this to allow more data transfer
with a single request. Completions to this request are bound by the
MPS setting for the bus. Aside from device quirks (none known), it
doesn't seem to make sense to set an MRRS value less than MPS, yet
this is a likely scenario given that user drivers do not have a
system-wide view of the PCI topology. Virtualize MRRS such that the
user can set MRRS >= MPS, but use MPS as the floor value that we'll
write to hardware.
Signed-off-by: Alex Williamson <alex.williamson@xxxxxxxxxx>
---
This patch seems like a bit of a gamble that we'll get more good out
of fixing up a potentially common inefficient configuration than
we'll see headache if there exist devices which require lower MRRS
settings. However, since the MPS setting should never be higher than
the MPSS allows, it seems outlandish that a device might require an
MRRS setting lower than MPSS.
Also noteworthy, pcie_write_mrrs() has a back-off algorithm which
expects the device to not accept unsupported MRRS values. This
code doesn't actually work because pcie_set_readrq() won't fail as
a result of this, but it also doesn't match how hardware works. In
the case of an Intel X540, I can use setpci on bare metal to write
whatever I want into MPS and MRRS and it sticks, just like it would
for the user with these registers virtualized. If there is hardware
that would reject values, it won't be reflected to the user unless we
write back the physical MRRS value to vconfig, which gets shakey
when we're masking the actual value we're writing in certain cases
anyway.
drivers/vfio/pci/vfio_pci_config.c | 29 ++++++++++++++++++++++++++---
1 file changed, 26 insertions(+), 3 deletions(-)
diff --git a/drivers/vfio/pci/vfio_pci_config.c b/drivers/vfio/pci/vfio_pci_config.c
index 91335e6de88a..115a36f6f403 100644
--- a/drivers/vfio/pci/vfio_pci_config.c
+++ b/drivers/vfio/pci/vfio_pci_config.c
@@ -808,6 +808,7 @@ static int vfio_exp_config_write(struct vfio_pci_device *vdev, int pos,
{
__le16 *ctrl = (__le16 *)(vdev->vconfig + pos -
offset + PCI_EXP_DEVCTL);
+ int readrq = le16_to_cpu(*ctrl) & PCI_EXP_DEVCTL_READRQ;
count = vfio_default_config_write(vdev, pos, count, perm, offset, val);
if (count < 0)
@@ -833,6 +834,27 @@ static int vfio_exp_config_write(struct vfio_pci_device *vdev, int pos,
pci_try_reset_function(vdev->pdev);
}
+ /*
+ * MPS is virtualized to the user, writes do not change the physical
+ * register since determining a proper MPS value requires a system wide
+ * device view. The MRRS is largely independent of MPS, but since the
+ * user does not have that system-wide view, they might set a safe, but
+ * inefficiently low value. Here we allow writes through to hardware,
+ * but we set the floor to the physical device MPS setting, so that
+ * we can at least use full TLPs, as defined by the MPS value.
+ *
+ * NB, if any devices actually depend on an artificially low MRRS
+ * setting, this will need to be revisited, perhaps with a quirk
+ * though pcie_set_readrq().
+ */
+ if (readrq != (le16_to_cpu(*ctrl) & PCI_EXP_DEVCTL_READRQ)) {
+ readrq = 128 <<
+ ((le16_to_cpu(*ctrl) & PCI_EXP_DEVCTL_READRQ) >> 12);
+ readrq = max(readrq, pcie_get_mps(vdev->pdev));
+
+ pcie_set_readrq(vdev->pdev, readrq);
+ }
+
return count;
}
@@ -851,11 +873,12 @@ static int __init init_pci_cap_exp_perm(struct perm_bits *perm)
* Allow writes to device control fields, except devctl_phantom,
* which could confuse IOMMU, MPS, which can break communication
* with other physical devices, and the ARI bit in devctl2, which
- * is set at probe time. FLR gets virtualized via our writefn.
+ * is set at probe time. FLR and MRRS get virtualized via our
+ * writefn.
*/
p_setw(perm, PCI_EXP_DEVCTL,
- PCI_EXP_DEVCTL_BCR_FLR | PCI_EXP_DEVCTL_PAYLOAD,
- ~PCI_EXP_DEVCTL_PHANTOM);
+ PCI_EXP_DEVCTL_BCR_FLR | PCI_EXP_DEVCTL_PAYLOAD |
+ PCI_EXP_DEVCTL_READRQ, ~PCI_EXP_DEVCTL_PHANTOM);
p_setw(perm, PCI_EXP_DEVCTL2, NO_VIRT, ~PCI_EXP_DEVCTL2_ARI);
return 0;
}
