Dear Laszlo,
Thank your very much for your review and detailed comment. and very sorry for the late response due to recently debug the wholes RAS solution.
On 2017/5/22 22:23, Laszlo Ersek wrote:
> Keeping some context:
>
> On 05/12/17 23:00, Laszlo Ersek wrote:
>> On 04/30/17 07:35, Dongjiu Geng wrote:
>>> This implements APEI GHES Table by passing the error cper info to
>>> the guest via a fw_cfg_blob. After a CPER info is added, an SEA/SEI
>>> exception will be injected into the guest OS.
>>>
>>> Below is the table layout, the max number of error soure is 11,
>>> which is classified by notification type.
>>>
>>> etc/acpi/tables etc/hardware_errors
>>> ================ ==========================================
>>> +-----------+
>>> +--------------+ | address | +-> +--------------+
>>> | HEST + | registers | | | Error Status |
>>> + +------------+ | +---------+ | | Data Block 1 |
>>> | | GHES1 | --> | |address1 | --------+ | +------------+
>>> | | GHES2 | --> | |address2 | ------+ | | CPER |
>>> | | GHES3 | --> | |address3 | ----+ | | | CPER |
>>> | | .... | --> | | ....... | | | | | CPER |
>>> | | GHES10 | --> | |address10| -+ | | | | CPER |
>>> +-+------------+ +-+---------+ | | | +-+------------+
>>> | | |
>>> | | +---> +--------------+
>>> | | | Error Status |
>>> | | | Data Block 2 |
>>> | | | +------------+
>>> | | | | CPER |
>>> | | | | CPER |
>>> | | +-+------------+
>>> | |
>>> | +-----> +--------------+
>>> | | Error Status |
>>> | | Data Block 3 |
>>> | | +------------+
>>> | | | CPER |
>>> | +-+------------+
>>> | ...........
>>> +--------> +--------------+
>>> | Error Status |
>>> | Data Block 10|
>>> | +------------+
>>> | | CPER |
>>> | | CPER |
>>> | | CPER |
>>> +-+------------+
>>>
>>> Signed-off-by: Dongjiu Geng <gengdongjiu@xxxxxxxxxx>
>>> ---
>>> default-configs/arm-softmmu.mak | 1 +
>>> hw/acpi/Makefile.objs | 1 +
>>> hw/acpi/aml-build.c | 2 +
>>> hw/acpi/hest_ghes.c | 203 +++++++++++++++++++++++++++++++++++
>>> hw/arm/virt-acpi-build.c | 6 ++
>>> include/hw/acpi/acpi-defs.h | 227 ++++++++++++++++++++++++++++++++++++++++
>>> include/hw/acpi/aml-build.h | 1 +
>>> include/hw/acpi/hest_ghes.h | 43 ++++++++
>>> 8 files changed, 484 insertions(+)
>>> create mode 100644 hw/acpi/hest_ghes.c create mode 100644
>>> include/hw/acpi/hest_ghes.h
>
>> Next file:
>>
>>> diff --git a/include/hw/acpi/hest_ghes.h
>>> b/include/hw/acpi/hest_ghes.h new file mode 100644 index
>>> 0000000..0cadc2b
>>> --- /dev/null
>>> +++ b/include/hw/acpi/hest_ghes.h
>>> @@ -0,0 +1,43 @@
>>> +#ifndef ACPI_GHES_H
>>> +#define ACPI_GHES_H
>>> +
>>> +#include "hw/acpi/bios-linker-loader.h"
>>> +
>>> +#define GHES_ERRORS_FW_CFG_FILE "etc/hardware_errors"
>>> +#define GHES_DATA_ADDR_FW_CFG_FILE "etc/hardware_errors_addr"
>>> +
>>> +#define GAS_ADDRESS_OFFSET 4
>>> +#define ERROR_STATUS_ADDRESS_OFFSET 20
>>> +#define NOTIFICATION_STRUCTURE 32
>>> +
>>> +#define BFAPEI_OK 0
>>> +#define BFAPEI_FAIL 1
>>> +
>>> +/* The max number of error source, the error sources
>>> + * are classified by notification type, below is the definition
>>> + * 0 - Polled
>>> + * 1 - External Interrupt
>>> + * 2 - Local Interrupt
>>> + * 3 - SCI
>>> + * 4 - NMI
>>> + * 5 - CMCI
>>> + * 6 - MCE
>>> + * 7 - GPIO-Signal
>>> + * 8 - ARMv8 SEA
>>> + * 9 - ARMv8 SEI
>>> + * 10 - External Interrupt - GSIV
>>> + */
>>> +#define MAX_ERROR_SOURCE_COUNT_V6 11
>>
>> I'll have to review this header file more thoroughly, once I see the
>> code that references these macros. For now, I have one comment:
>>
>> (42) I think the notification type list should be removed from this
>> location. Also, the open-coded value 11 should be replaced with the
>> ACPI_HEST_NOTIFY_RESERVED enumeration constant.
>>
>> I will try to continue reviewing this patch sometime next week
>> (second half of the week at the earliest, I think).
>
> (43) I think all macros introduced in this header should all start
> with "GHES_".
Ok.
>
>>
>>> +/* The max size in Bytes for one error block */
>>> +#define MAX_RAW_DATA_LENGTH 0x1000
>>> +
>>> +typedef struct GhesErrorState {
>>> + uint64_t physical_addr;
>>> + uint64_t ghes_addr_le[8];
>>> +} GhesErrorState;
>
> (44) Should this be called "GhesState" instead (dropping "Error")?
good suggestion.
>
> (45) (This is a question for other reviewers) I have no idea if this
> abstraction should be a device (sysbus or otherwise). Should it be a
> device? Below we have a static ("global") variable of this type, which
> is quite unusual.
Before I also indeed consider this question that whether this abstraction should be a device, maybe global variable is clean. anyway I will consider again about this point.
>
> (46) What is "physical_addr" good for? Below I can only see an
> assignment to it, in ghes_update_guest(). Where is the field read?
this "physical_addr" address is the physical error address in the CPER.
such as the physical address that happen hwpoison, this address is delivered by the KVM and QEMU transfer this address to physical.
>
> (47) "ghes_addr_le" should be an array of eight uint8_t elements (for
> representing a single uint64_t in little endian). The declaration
> above has a typo; the element type is currently specified as uint64_t.
>
> It suffices for the firmware to pass the base address of
> "etc/hardware_errors" back to QEMU, all the other addresses can be
> computed in QEMU as needed.
>
> (If, for some reason you *do* need to pass back multiple addresses,
> then you should use
>
> uint8_t xxxx_addr_le[N][8];
>
> But even in this case, setting N to 8 doesn't look useful, because we
> have 11 error sources / notification types.)
Thanks for this suggestion. it seems good.
>
>>> +
>>> +void ghes_build_acpi(GArray *table_data, GArray *hardware_error,
>>> + BIOSLinker *linker); void
>>> +ghes_add_fw_cfg(FWCfgState *s, GArray *guid);
>
> (48) The second parameter should be called "hardware_errors", not
> "guid".
Ok, will change it.
>
>>> +void ghes_update_guest(uint32_t notify, uint64_t physical_address);
>
> (49) Can you call the second parameter "error_physical_addr"?
Ok, will change it.
>
>>> +#endif
>>>
>
>>> diff --git a/default-configs/arm-softmmu.mak
>>> b/default-configs/arm-softmmu.mak index 1e3bd2b..d5f1552 100644
>>> --- a/default-configs/arm-softmmu.mak
>>> +++ b/default-configs/arm-softmmu.mak
>>> @@ -121,3 +121,4 @@ CONFIG_ACPI=y
>>> CONFIG_SMBIOS=y
>>> CONFIG_ASPEED_SOC=y
>>> CONFIG_GPIO_KEY=y
>>> +CONFIG_ACPI_APEI_GENERATION=y
>
>>> diff --git a/hw/acpi/Makefile.objs b/hw/acpi/Makefile.objs index
>>> 11c35bc..776b46e 100644
>>> --- a/hw/acpi/Makefile.objs
>>> +++ b/hw/acpi/Makefile.objs
>>> @@ -6,6 +6,7 @@ common-obj-$(CONFIG_ACPI_MEMORY_HOTPLUG) +=
>>> memory_hotplug.o
>>> common-obj-$(CONFIG_ACPI_CPU_HOTPLUG) += cpu.o
>>> common-obj-$(CONFIG_ACPI_NVDIMM) += nvdimm.o
>>> common-obj-$(CONFIG_ACPI_VMGENID) += vmgenid.o
>>> +common-obj-$(CONFIG_ACPI_APEI_GENERATION) += hest_ghes.o
>>> common-obj-$(call lnot,$(CONFIG_ACPI_X86)) += acpi-stub.o
>>>
>>> common-obj-y += acpi_interface.o
>
> (50) I think "CONFIG_ACPI_APEI" would be more succinct.
OK, I will change it.
>
>>> diff --git a/include/hw/acpi/aml-build.h
>>> b/include/hw/acpi/aml-build.h index 00c21f1..c1d15b3 100644
>>> --- a/include/hw/acpi/aml-build.h
>>> +++ b/include/hw/acpi/aml-build.h
>>> @@ -211,6 +211,7 @@ struct AcpiBuildTables {
>>> GArray *rsdp;
>>> GArray *tcpalog;
>>> GArray *vmgenid;
>>> + GArray *hardware_errors;
>>> BIOSLinker *linker;
>>> } AcpiBuildTables;
>>>
>
>>> diff --git a/hw/acpi/aml-build.c b/hw/acpi/aml-build.c index
>>> c6f2032..802b98d 100644
>>> --- a/hw/acpi/aml-build.c
>>> +++ b/hw/acpi/aml-build.c
>>> @@ -1560,6 +1560,7 @@ void acpi_build_tables_init(AcpiBuildTables *tables)
>>> tables->table_data = g_array_new(false, true /* clear */, 1);
>>> tables->tcpalog = g_array_new(false, true /* clear */, 1);
>>> tables->vmgenid = g_array_new(false, true /* clear */, 1);
>>> + tables->hardware_errors = g_array_new(false, true /* clear */,
>>> + 1);
>>> tables->linker = bios_linker_loader_init(); }
>>>
>>> @@ -1570,6 +1571,7 @@ void acpi_build_tables_cleanup(AcpiBuildTables *tables, bool mfre)
>>> g_array_free(tables->table_data, true);
>>> g_array_free(tables->tcpalog, mfre);
>>> g_array_free(tables->vmgenid, mfre);
>>> + g_array_free(tables->hardware_errors, mfre);
>>> }
>>>
>>> /* Build rsdt table */
>
> Looks good to me.
thanks.
>
>>> diff --git a/hw/arm/virt-acpi-build.c b/hw/arm/virt-acpi-build.c
>>> index 0835e59..e7ab5dc 100644
>>> --- a/hw/arm/virt-acpi-build.c
>>> +++ b/hw/arm/virt-acpi-build.c
>>> @@ -45,6 +45,8 @@
>>> #include "hw/arm/virt.h"
>>> #include "sysemu/numa.h"
>>> #include "kvm_arm.h"
>>> +#include "hw/acpi/vmgenid.h"
>
> (51) I think this include directive is not necessary.
sorry, this is my typo error, will remove it.
>
>>> +#include "hw/acpi/hest_ghes.h"
>>>
>>> #define ARM_SPI_BASE 32
>>> #define ACPI_POWER_BUTTON_DEVICE "PWRB"
>>> @@ -778,6 +780,9 @@ void virt_acpi_build(VirtMachineState *vms, AcpiBuildTables *tables)
>>> acpi_add_table(table_offsets, tables_blob);
>>> build_spcr(tables_blob, tables->linker, vms);
>>>
>>> + acpi_add_table(table_offsets, tables_blob);
>>> + ghes_build_acpi(tables_blob, tables->hardware_errors,
>>> + tables->linker);
>>> +
>>> if (nb_numa_nodes > 0) {
>>> acpi_add_table(table_offsets, tables_blob);
>>> build_srat(tables_blob, tables->linker, vms); @@ -892,6
>>> +897,7 @@ void virt_acpi_setup(VirtMachineState *vms)
>>>
>>> build_state->rsdp_mr = acpi_add_rom_blob(build_state, tables.rsdp,
>>> ACPI_BUILD_RSDP_FILE,
>>> 0);
>>> + ghes_add_fw_cfg(vms->fw_cfg, tables.hardware_errors);
>>>
>>> qemu_register_reset(virt_acpi_build_reset, build_state);
>>> virt_acpi_build_reset(build_state);
>
> (52) I think for consistency with existing code, this function call
> should be placed between the ACPI_BUILD_TPMLOG_FILE line and the
> acpi_add_rom_blob() line.
OK.
>
>>> diff --git a/hw/acpi/hest_ghes.c b/hw/acpi/hest_ghes.c new file mode
>>> 100644 index 0000000..91d382e
>>> --- /dev/null
>>> +++ b/hw/acpi/hest_ghes.c
>>> @@ -0,0 +1,203 @@
>>> +/*
>>> + * APEI GHES table Generation
>>> + *
>>> + * Copyright (C) 2017 huawei.
>>> + *
>>> + * Author: Dongjiu Geng <gengdongjiu@xxxxxxxxxx>
>>> + *
>>> + * This work is licensed under the terms of the GNU GPL, version 2 or later.
>>> + * See the COPYING file in the top-level directory.
>>> + *
>>> + */
>>> +
>>> +#include "qemu/osdep.h"
>>> +#include "qmp-commands.h"
>>> +#include "hw/acpi/acpi.h"
>>> +#include "hw/acpi/aml-build.h"
>>> +#include "hw/acpi/hest_ghes.h"
>>> +#include "hw/nvram/fw_cfg.h"
>>> +#include "sysemu/sysemu.h"
>>> +
>>> +static int ghes_generate_cper_record(uint64_t block_error_address,
>>> + uint64_t error_physical_addr) {
>>> + AcpiGenericErrorStatus block;
>>> + AcpiGenericErrorData *gdata;
>>> + struct cper_sec_mem_err *mem_err;
>>> + uint64_t block_data_length;
>>> + unsigned char *buffer;
>>> +
>>> + cpu_physical_memory_read(block_error_address, &block,
>>> + sizeof(AcpiGenericErrorStatus));
>>> +
>>> + block_data_length = sizeof(AcpiGenericErrorStatus) +
>>> + block.data_length;
>
> (53) "block.data_length" must surely be converted from LE to
> host-endian, so please wrap it with le32_to_cpu().
OK.
>
>>> +
>>> + /* If the Generic Error Status Block is NULL, update
>>> + * the block header
>>> + */
>>> + if (!block.block_status) {
>>> + block.block_status = ACPI_BERT_UNCORRECTABLE;
>>> + block.error_severity = CPER_SEV_FATAL;
>>> + }
>>> +
>>> + block.data_length += sizeof(AcpiGenericErrorData);
>>> + block.data_length += sizeof(struct cper_sec_mem_err);
>
> (54) Conversion between LE and host-endian is missing.
OK.
>
> (55) What happens if you run out of the preallocated memory?
if it run out of the preallocated memory. it will overwrite other
error source. every block's size is fixed. so it does not easy dynamically extend the size if it is overflow.
Anyway I will add a error report if it happens overwrite.
>
>>> +
>>> + /* Write back the Generic Error Status Block to guest memory */
>>> + cpu_physical_memory_write(block_error_address, &block,
>>> + sizeof(AcpiGenericErrorStatus));
>>> +
>>> + /* Fill in Generic Error Data Entry */
>>> + buffer = g_malloc(sizeof(AcpiGenericErrorData) + sizeof(cper_sec_mem_err));
>>> + memset(buffer, 0, sizeof(AcpiGenericErrorData) +
>>> + sizeof(cper_sec_mem_err));
>
> (56) Please use g_malloc0() instead.
Ok.
>
>>> + gdata = (AcpiGenericErrorData *)buffer;
>>> +
>>> + memcpy(gdata->section_type, (void *) &CPER_SEC_PLATFORM_MEM,
>>> + sizeof(uuid_le));
>>> + gdata->error_data_length = sizeof(struct cper_sec_mem_err);
>
> (57) Endianness conversion missing (cpu_to_le32()).
Thanks for the reminder.
>
>>> +
>>> + mem_err = (struct cper_sec_mem_err *) (gdata + 1);
>>> +
>>> + /* In order to simplify simulation, hardcode the CPER section to memory
>>> + * section.
>>> + */
>>> + mem_err->validation_bits |= CPER_MEM_VALID_ERROR_TYPE;
>>> + mem_err->error_type = 3;
>
> (58) Is this supposed to stand for "Multi-bit ECC" (from "N.2.5 Memory
> Error Section" in UEFI 2.6)? Should we have a macro for that?
Yes, it is. What do you mean a macro? For all the errors that happen in the guest OS,
in order to simulate easy, I abstract all the error section to memory section, even though the error section is processor or other section.
I do not know whether do you have some suggestion for that.
>>> +
>>> + mem_err->validation_bits |= CPER_MEM_VALID_PA;
>>> + mem_err->physical_addr = error_physical_addr;
>
> (59) Conversion between host and little endian is missing on all four
> lines above.
Thanks.
>
>>> +
>>> + mem_err->validation_bits |= CPER_MEM_VALID_CARD | CPER_MEM_VALID_MODULE |
>>> + CPER_MEM_VALID_BANK | CPER_MEM_VALID_ROW |
>>> + CPER_MEM_VALID_COLUMN | CPER_MEM_VALID_BIT_POSITION;
>>> + mem_err->card = 1;
>>> + mem_err->module = 2;
>>> + mem_err->bank = 3;
>>> + mem_err->row = 1;
>>> + mem_err->column = 2;
>>> + mem_err->bit_pos = 5;
>
> (60) I have no idea where these values come from.
For all the errors that happen in the guest OS,
in order to simulate easy, I abstract all the error section to memory section, and hard code the memory section error value as above.
>
>>> +
>>> + mem_err->validation_bits |= CPER_MEM_VALID_ERROR_STATUS;
>>> + mem_err->error_status = 4 << 8;
>>> +
>>> + /* Write back the Generic Error Data Entry to guest memory */
>>> + cpu_physical_memory_write(block_error_address + block_data_length, buffer,
>>> + sizeof(AcpiGenericErrorData) +
>>> + sizeof(cper_sec_mem_err));
>
> (61) Please choose a better name for "block_data_length" -- it stands
> for the length *before* the increment.
OK, thanks for the suggestion.
>
> (62) Is it safe to write out the increased block length before writing
> the new CPER data?
It indeed needs to add a judgment to avoid the data overflow, if overflow, report an error.
As we talk before, the total size for a block is fixed. So cannot dynamic extend the total size. So if is overflowed, will let the CPER adding is failed.
>
>>> +
>>> + g_free(buffer);
>>> + return BFAPEI_OK;
>>> +}
>
> (63) This return code is not used. Can we remove it perhaps (together
> with the BFAPEI_* macros)?
OK. Thanks Laszlo. Will remove it.
>
>>> +
>>> +void ghes_build_acpi(GArray *table_data, GArray *hardware_error,
>>> + BIOSLinker *linker) {
>>> + Aml *hest;
>>> + uint32_t address_registers_offset;
>>> + AcpiTableHeader *header;
>>> + AcpiGenericHardwareErrorSource *error_source;
>>> + int i;
>>> +
>>> + int block_reqr_size = sizeof(uint64_t) + MAX_RAW_DATA_LENGTH;
>
> (64) What does "reqr" stand for?
It stand for the request size.
>
>>> +
>>> + /* New address register and Error status block table size*/
>>> + g_array_set_size(hardware_error, MAX_ERROR_SOURCE_COUNT_V6
>>> + * block_reqr_size);
>
> (65) The QEMU coding style is
>
> g_array_set_size(hardware_error, MAX_ERROR_SOURCE_COUNT_V6 *
> block_reqr_size);
>
> That is, the operator is at the end of the line.
>
> Several function calls below are affected by this; please fix them all
> up.
>
> Running "scripts/checkpatch.pl" on the patches before you post them
> should help catch this kind of problem early.
I have ran the "scripts/checkpatch.pl" before post these patches, it does not remind such errors. anyway I will modified it.
>
>>> +
>>> + /* Put this in a HEST table */
>>> + hest = init_aml_allocator();
>>> + address_registers_offset = table_data->len
>>> + + sizeof(AcpiHardwareErrorSourceTable)
>>> + + ERROR_STATUS_ADDRESS_OFFSET
>>> + + GAS_ADDRESS_OFFSET;
>
> (66) Please drop the ERROR_STATUS_ADDRESS_OFFSET and
> GAS_ADDRESS_OFFSET macros (from the header file as well), and use the
> following expressions
> instead:
>
> ...
> offsetof(AcpiGenericHardwareErrorSource, error_status_address) +
> offsetof(AcpiGenericAddress, address);
Good suggestion and point.
>
>>> + /* Reserve space for HEST table size*/
>>> + acpi_data_push(hest->buf, sizeof(AcpiHardwareErrorSourceTable)
>>> + + MAX_ERROR_SOURCE_COUNT_V6
>>> + *
>>> + sizeof(AcpiGenericHardwareErrorSource));
>>> +
>>> + g_array_append_vals(table_data, hest->buf->data,
>>> + hest->buf->len);
>
> (67) HEST is a data table, it contains no AML. Accordingly, you use
> "hest" *only* for pushing zero bytes to "table_data".
>
> But that's not a good enough reason to have "hest" at all, or to call
> init_aml_allocator() / free_aml_allocator(). Instead, please just
> calculate the needed size, and push that many bytes directly to
> "table_data".
The hest table indeed does not include AML, so will do it according to your suggestion.
>
> Your current code already populates those bytes within "table_data",
> so that's good.
>
>>> + /* Allocate guest memory for the Data fw_cfg blob */
>>> + bios_linker_loader_alloc(linker, GHES_ERRORS_FW_CFG_FILE,
>>> + hardware_error, 4096,
>>> + false /* page boundary, high memory
>>> + */);
>
> (68) In the code below, you are not taking an "OVMF header probe
> suppressor" into account.
>
> But, we have already planned to replace that quirk with a separate,
> dedicated allocation hint or command, so I'm not going to describe
> what an "OVMF header probe suppressor" is; instead, I'll describe the
> replacement for it.
>
> So please add a new patch to the series that does the following:
OK.
>
> - In "hw/acpi/bios-linker-loader.c", modify the documentation of
> "BiosLinkerLoaderEntry.alloc.zone". The most significant bit (i.e.,
> bit 7), when set, should mean that @alloc.file contains no ACPI
> tables. When the bit is clear, no information is given about the
> contents of @alloc.file (i.e., same as now).
>
> - This will require a small patch for SeaBIOS: mask off bit 7 of
> "entry->alloc.zone" in the switch statement in
> romfile_loader_allocate(), "src/fw/romfile_loader.c". SeaBIOS does not
> have to care about this bit.
Your description is detailed, thanks again, I will do that.
>
> - OVMF will need some code to handle this bit specially, but I will
> write that.
Ok, it is good.
>
> - In QEMU, please modify the bios_linker_loader_alloc() function so that
> it takes a "noacpi" boolean as well, and set the high bit of
> "entry.alloc.zone" from it. The default value for "noacpi" should be
> false, at all currently existing call sites.
>
> - And finally, in this patch, we should pass "true" as "noacpi".
I basically understand your idea.
>
>>> + header = (AcpiTableHeader *)(table_data->data
>>> + + table_data->len - hest->buf->len);
>>> + *(uint32_t *)(header + 1) = MAX_ERROR_SOURCE_COUNT_V6;
>
> (69) Ugh, this is ugly. Please access the error source count field
> through "AcpiHardwareErrorSourceTable.error_source_count".
OK.
>
>>> + error_source = (AcpiGenericHardwareErrorSource *)((char *)header
>>> + +
>>> + sizeof(AcpiHardwareErrorSourceTable));
>>> +
>>> + for (i = 0; i < MAX_ERROR_SOURCE_COUNT_V6; i++) {
>>> + error_source->type = ACPI_HEST_TYPE_GENERIC_ERROR;
>>> + error_source->source_id = 0;
>
> (70) I think this is wrong, this identifier should be unique among all
> error sources. You should assign cpu_to_le16(i).
Thanks for the point, you are right, this is wrong, the source id is Uniquely identify
>
>>> + error_source->related_source_id = 0xffff;
>>> + error_source->flags = 0;
>>> + error_source->enabled = 1;
>>> + error_source->number_of_records = 1;
>
> (71) Why do we pre-alloc only one record? Don't several CPER objects
> fit in an error status data block (of size MAX_RAW_DATA_LENGTH, 0x1000)?
>From my understanding, number_of_records stands for the number of error data status data block.
Here setting the number_of_records to 1 means that one error source includes one error source status data block.
But One error source status data block can includes many CPER objects. So although pre-alloc only one record, but it can still
Includes several CPER objects.
>
>>> + error_source->max_sections_per_record = 1;
>>> + error_source->max_raw_data_length = MAX_RAW_DATA_LENGTH;
>>> + error_source->error_status_address.space_id =
>>> + ACPI_ADR_SPACE_SYSTEM_MEMORY;
>>> + error_source->error_status_address.bit_width = 64;
>>> + error_source->error_status_address.bit_offset = 0;
>>> + error_source->error_status_address.access_width = 4;
>>> + error_source->notify.type = i;
>
> OK, this is one byte wide only.
>
>>> + error_source->notify.length =
>>> + sizeof(AcpiGenericHardwareErrorSource);
>
> (72) This seems to be wrong. The right hand side should be
> sizeof(AcpiHestNotify).
Thanks Laszlo's carefully review, this is wrong, it should be sizeof(AcpiHestNotify).
>
>>> +
>>> + bios_linker_loader_add_pointer(linker, GHES_ERRORS_FW_CFG_FILE,
>>> + sizeof(uint64_t) * i, sizeof(uint64_t),
>>> + GHES_ERRORS_FW_CFG_FILE,
>>> + MAX_ERROR_SOURCE_COUNT_V6 * sizeof(uint64_t) +
>>> + i * MAX_RAW_DATA_LENGTH);
>
> (73) Looks good, but please indent the arguments 1 position relative
> to the opening paren.
Ok, thanks for the comment.
>
>>> + bios_linker_loader_add_pointer(linker, ACPI_BUILD_TABLE_FILE,
>>> + address_registers_offset
>>> + + i * sizeof(AcpiGenericHardwareErrorSource),
>>> + sizeof(uint32_t), GHES_ERRORS_FW_CFG_FILE,
>>> + i * sizeof(uint64_t));
>
> (74) Passing "sizeof(uint32_t)" as "dst_patched_size" is wrong. The
> address registers at the start of the "etc/hardware_errors" blob are
> 64-bit wide each.
thanks a lot for the point, you are right. I am wrong.
>
>>> +
>>> + bios_linker_loader_write_pointer(linker, GHES_DATA_ADDR_FW_CFG_FILE,
>>> + i * sizeof(uint64_t), sizeof(uint64_t),
>>> + GHES_ERRORS_FW_CFG_FILE,
>>> + MAX_ERROR_SOURCE_COUNT_V6 * sizeof(uint64_t) +
>>> + i * MAX_RAW_DATA_LENGTH);
>
> (75) We should create only one WRITE_POINTER command, for the base
> address of "etc/hardware_errors". This should be done outside of the
> loop.
>
> The base addresses of the individual error status data blocks should
> be calculated in ghes_update_guest(), based on the error source /
> notification type.
Thanks a lot for the review, you are right, I will modify it.
>
>>> + error_source++;
>>> + }
>>> +
>>> + build_header(linker, table_data,
>>> + (void *)header, "HEST", hest->buf->len, 1, NULL, "GHES");
>
> (76) Any particular reason for not passing NULL in "oem_table_id"?
>
>>> +
>>> + free_aml_allocator();
>>> +}
>>> +
>>> +static GhesErrorState ges;
>>> +void ghes_add_fw_cfg(FWCfgState *s, GArray *hardware_error) {
>>> +
>>> + int block_reqr_size = sizeof(uint64_t) + MAX_RAW_DATA_LENGTH;
>>> + int size = MAX_ERROR_SOURCE_COUNT_V6 * block_reqr_size;
>
> (77) These variable should have type "size_t".
>
> (78) What does "reqr" stand for?
Reqr is request size for block.
>
> (79) I just noticed that the commit message lists error sources /
> notification types 1 through 10 (count=10 in total). However, we have
> 11 error sources actually. Can you update the commit message so that
> it mentions sources 0 through 10?
OK, thanks very much for your suggestion.
>
>>> +
>>> + /* Create a read-only fw_cfg file for GHES */
>>> + fw_cfg_add_file(s, GHES_ERRORS_FW_CFG_FILE, hardware_error->data,
>>> + size);
>>> + /* Create a read-write fw_cfg file for Address */
>>> + fw_cfg_add_file_callback(s, GHES_DATA_ADDR_FW_CFG_FILE, NULL, NULL,
>>> + &(ges.ghes_addr_le[0]),
>>> + sizeof(uint64_t) * MAX_ERROR_SOURCE_COUNT_V6,
>>> + false); }
>>> +
>
> (80) The size calculation for GHES_DATA_ADDR_FW_CFG_FILE is incorrect.
> First, it does not match the element count 8 that I highlighted under
> remark (47). Second (again), passing back just the base address is
> sufficient, so 8 uint8_t elements (for representing a single uint64_t
> in
> LE) are enough.
>
> In other words, the size calculation should be
> ARRAY_SIZE(ges.ghes_addr_le) here.
I will consider your suggestion, thanks very much.
>
>>> +void ghes_update_guest(uint32_t notify, uint64_t physical_address)
>>> +{
>>> + uint64_t block_error_addr;
>>> +
>>> + if (physical_address) {
>>> + ges.physical_addr = physical_address;
>>> + block_error_addr = ges.ghes_addr_le[notify];
>>> + block_error_addr = le32_to_cpu(block_error_addr);
>>> +
>>> + /* A zero value in ghes_addr means that BIOS has not yet written
>>> + * the address
>>> + */
>>> + if (block_error_addr) {
>>> + ghes_generate_cper_record(block_error_addr, physical_address);
>>> + }
>>> + }
>>> +}
>
> (81) First, the value of "notify" should be range-checked before using
> it as an array subscript. If it is outside of the permissible range,
> nothing should be done. Second, in order to locate the affected error
> status data block, we should move the offset calculation here, from
> ghes_build_acpi().
>
Thanks Laszlo, I will consider your suggestion.
> Thanks
> Laszlo
>
> .
>
