This is v2 of vt-d unit test series.
Patch "libcflat: add IS_ALIGNED() macro, and page sizes" is picked up
by Drew in the ARM GIC framework series, so please feel free to drop
it when needed.
v2:
- move cpu_relax patch to the beginning, and use them in all places
[Drew]
- replace all corresponding 256 into PCI_DEVFN_MAX, as well for
PCI_BAR_NUM [Drew]
- adding is_power_of_2() to replace ONE_BIT_ONLY() [Drew]
- add SZ_64K macro [Drew]
- declare pci_config_write[wb] in lib/asm-generic/pci-host-bridge.h [Alex]
- edu_reg_read/write() add "l" in func name [Drew]
- drop pci_set_master(), instead, provide pci_cmd_set_clr() [Drew]
- change return code into bool (always) for functions that apply
[Drew]
- keep old pci_find_dev() interface [Drew/Alex]
- use __raw_{read|write}*() for both vt-d and edu register read/writes
[Alex]
- remove pci_ prefix for all pci_dev fields [Drew]
- replace 0xff in cap_handlers[0xff] into (PCI_CAP_ID_MAX + 1) [Drew]
- make x86/unittest.cfg simpler by using q35 directly with eim=off
[Drew]
RFC -> v1:
- when init edu device fail, report_skip() rather than return error
[Radim]
- use asserts rather than "static bool inited" to avoid multiple init
of components (affects patch 1/2) [Drew]
- moving the first two patches out of the series [Drew]
- int vtd_init(), do not setup_idt() since smp_init() did it [Drew]
- when edu do not have MSI enabled, skip interrupt test [Radim]
- rename vtd_reg_*() into vtd_{read|write}[lq](), and move them to
header file [Drew]
- use PAGE_MASK when able [Drew]
- use "&" instead of "|" in intel-iommu init test (three places)
[Drew]
- use "vtd_init()" in unit test [Drew]
- mention that where intel-iommu.h comes from [Drew]
- re-written vtd_gcmd_or(), make it also work on even hardware [Drew]
- remove most of the oneline wrapper for VT-d registers, instead, use
vtd_{read|write}* with register names [Drew]
- remove useless BDF helpers [Drew]
- move edu device macros into header file [Drew]
- make edu_check_alive static inline [Drew]
- remove all useless wrappers in pci-edu.c [Drew]
- remove pci_dma_dir_t and all its users, instead, use "bool
from_device" [Drew]
- not use typedef for structs, to follow Linux/kvm-unit-tests coding
style [Drew]
- let pci_dev_init() clean and simple, then provide
pci_enable_defaults() for more complicated things [Drew]
- add one more patch to add intel-iommu test into x86/unittest [Radim]
- use 0x60 intr request instead of factorial to trigger edu device
interrupt [Drew]
- ...and some other changes I just forgot to note down...
Currently only a very small test scope is covered:
* VT-d init
* DMAR: 4 bytes copy
* IR: MSI
However this series could be a base point to add more test cases for
VT-d. The problem is, there are many IOMMU error conditions which are
very hard to be triggered in a real guest (IOMMU has merely no
interface for guest user, and it's totally running in the background).
This piece of work can be a start point if we want to do more
complicated things and play around with Intel IOMMU devices (also for
IOMMU regression tests).
Please review. Thanks,
=================
To run the test:
./x86/run ./x86/intel-iommu.flat \
-M q35,kernel-irqchip=split -global ioapic.version=0x20 \
-device intel-iommu,intremap=on -device edu
Sample output:
pxdev:kvm-unit-tests [new-iommu-ut]# ./iommu_run.sh
/root/git/qemu/bin/x86_64-softmmu/qemu-system-x86_64 -enable-kvm -device pc-testdev -device isa-debug-exit,iobase=0xf4,iosize=0x4 -vnc none -serial stdio
+-device pci-testdev -kernel ./x86/intel-iommu.flat -M q35,kernel-irqchip=split -global ioapic.version=0x20 -device intel-iommu,intremap=on -device edu
enabling apic
paging enabled
cr0 = 80010011
cr3 = 7fff000
cr4 = 20
VT-d version: 0x10
cap: 0x0012008c22260206
ecap: 0x0000000000f00f1a
PASS: init status check
PASS: fault status check
PASS: QI enablement
DMAR table address: 0x0000000007ff9000
PASS: DMAR table setup
IR table address: 0x0000000007ff8000
PASS: IR table setup
PASS: DMAR enablement
PASS: IR enablement
PASS: DMAR support 39 bits address width
PASS: DMAR support huge pages
PCI: init dev 0x0020 BAR 0 [MEM] addr 0xfea00000
PCI detected cap 0x5
Detected MSI for device 0x20 offset 0x40
allocated vt-d root entry for PCI bus 0
allocated vt-d context entry for devfn 0x20
map 4K page IOVA 0x0 to 0x7ff7000 (sid=0x0020)
edu device DMA start TO addr 0x0 size 0x4 off 0x0
edu device DMA start FROM addr 0x4 size 0x4 off 0x0
PASS: DMAR 4B memcpy test
INTR: setup IRTE index 0
MSI: dev 0x20 init 64bit address: addr=0xfee00010, data=0x0
PASS: EDU factorial INTR test
Peter Xu (17):
x86/asm: add cpu_relax()
libcflat: introduce is_power_of_2()
x86: intel-iommu: add vt-d init test
libcflat: add IS_ALIGNED() macro, and page sizes
libcflat: moving MIN/MAX here
vm/page: provide PGDIR_OFFSET() macro
pci: introduce struct pci_dev
pci: provide pci_scan_bars()
x86/vmexit: leverage pci_scan_bars()
pci: provide pci_cmd_set_clr()
pci: provide pci_enable_defaults()
pci: add bdf helpers
pci: edu: introduce pci-edu helpers
x86: intel-iommu: add dmar test
pci: add msi support for 32/64bit address
x86: intel-iommu: add IR MSI test
x86/unittests: add intel-iommu test
lib/alloc.c | 3 -
lib/libcflat.h | 14 +++
lib/pci-edu.c | 73 ++++++++++++
lib/pci-edu.h | 83 +++++++++++++
lib/pci-host-generic.c | 9 +-
lib/pci-testdev.c | 10 +-
lib/pci.c | 154 ++++++++++++++++++++----
lib/pci.h | 39 ++++--
lib/x86/asm/barrier.h | 11 ++
lib/x86/asm/page.h | 3 +
lib/x86/intel-iommu.c | 313 +++++++++++++++++++++++++++++++++++++++++++++++++
lib/x86/intel-iommu.h | 142 ++++++++++++++++++++++
lib/x86/vm.c | 4 +-
x86/Makefile.common | 1 +
x86/Makefile.x86_64 | 2 +
x86/intel-iommu.c | 119 +++++++++++++++++++
x86/unittests.cfg | 7 ++
x86/vmexit.c | 27 ++---
18 files changed, 955 insertions(+), 59 deletions(-)
create mode 100644 lib/pci-edu.c
create mode 100644 lib/pci-edu.h
create mode 100644 lib/x86/intel-iommu.c
create mode 100644 lib/x86/intel-iommu.h
create mode 100644 x86/intel-iommu.c
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe kvm" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
