On Mon, May 25, 2015 at 09:21:49AM +0300, Vasiliy Tolstov wrote:
> 2015-05-23 6:55 GMT+03:00 Kevin O'Connor <kevin@xxxxxxxxxxxx>:
> > Out of curiosity, I ran some additional timing tests. With SeaBIOS
> > fully stripped down (via Kconfig), it takes ~20ms to get to the boot
> > phase on my old AMD system. Of that 20ms, ~7ms is to enable shadow
> > ram, 2ms is to calibrate the cpu timestamp counter, 4ms is for pci
> > init, and ~6ms is to make the shadow ram area read-only. The time in
> > the remaining parts of the SeaBIOS code is so small that it's hard to
> > measure.
>
> Can you share config for seabios? As i understand i can safety to
> remove keybord, ps2, usb, ata/ahci and leave only virtio (in case of
> using qemu to boo linux/freebsd/windows systems) ?
To get to 20ms, I basically disabled everything. (Actually, after
sending my last email I found I cound get to 16ms by setting
CONFIG_WRITABLE_UPPERMEMORY=y - it avoids much of the shadow ram
read-only cost.) It's not possible to actually boot anything with
this config - I was instead timing to the point where one could add a
multiboot or vmlinux boot capability to SeaBIOS.
To get to these times I disabled debug messages themselves (they take
a few ms of the boot time). So, to time events without debug messages
I added a few outb() calls to seabios at critical points. See patch
and config below.
-Kevin
--- a/src/post.c
+++ b/src/post.c
@@ -167,11 +167,15 @@ platform_hardware_setup(void)
// Init base pc hardware.
pic_setup();
mathcp_setup();
+ outb('3', 0x402); outb('\n', 0x402);
timer_setup();
+ outb('4', 0x402); outb('\n', 0x402);
clock_setup();
// Platform specific setup
+ outb('5', 0x402); outb('\n', 0x402);
qemu_platform_setup();
+ outb('6', 0x402); outb('\n', 0x402);
coreboot_platform_setup();
}
@@ -200,6 +204,7 @@ startBoot(void)
// Clear low-memory allocations (required by PMM spec).
memset((void*)BUILD_STACK_ADDR, 0, BUILD_EBDA_MINIMUM - BUILD_STACK_ADDR);
+ outb('8', 0x402); outb('\n', 0x402);
dprintf(3, "Jump to int19\n");
struct bregs br;
memset(&br, 0, sizeof(br));
@@ -247,6 +252,7 @@ maininit(void)
prepareboot();
// Write protect bios memory.
+ outb('7', 0x402); outb('\n', 0x402);
make_bios_readonly();
// Invoke int 19 to start boot process.
@@ -331,12 +337,14 @@ handle_post(void)
serial_debug_preinit();
debug_banner();
+ outb('1', 0x402); outb('\n', 0x402);
// Check if we are running under Xen.
xen_preinit();
// Allow writes to modify bios area (0xf0000)
make_bios_writable();
+ outb('2', 0x402); outb('\n', 0x402);
// Now that memory is read/writable - start post process.
dopost();
#
# Automatically generated file; DO NOT EDIT.
# SeaBIOS Configuration
#
#
# General Features
#
# CONFIG_COREBOOT is not set
CONFIG_QEMU=y
# CONFIG_CSM is not set
CONFIG_QEMU_HARDWARE=y
# CONFIG_XEN is not set
# CONFIG_THREADS is not set
# CONFIG_RELOCATE_INIT is not set
# CONFIG_BOOTMENU is not set
# CONFIG_BOOTORDER is not set
CONFIG_ENTRY_EXTRASTACK=y
CONFIG_MALLOC_UPPERMEMORY=y
CONFIG_ROM_SIZE=0
#
# Hardware support
#
# CONFIG_ATA is not set
# CONFIG_AHCI is not set
# CONFIG_SDCARD is not set
# CONFIG_VIRTIO_BLK is not set
# CONFIG_VIRTIO_SCSI is not set
# CONFIG_PVSCSI is not set
# CONFIG_ESP_SCSI is not set
# CONFIG_LSI_SCSI is not set
# CONFIG_MEGASAS is not set
# CONFIG_FLOPPY is not set
# CONFIG_PS2PORT is not set
# CONFIG_USB is not set
# CONFIG_SERIAL is not set
# CONFIG_LPT is not set
# CONFIG_USE_SMM is not set
CONFIG_MTRR_INIT=y
CONFIG_PMTIMER=y
#
# BIOS interfaces
#
CONFIG_DRIVES=y
CONFIG_CDROM_BOOT=y
CONFIG_CDROM_EMU=y
CONFIG_PCIBIOS=y
CONFIG_APMBIOS=y
CONFIG_PNPBIOS=y
# CONFIG_OPTIONROMS is not set
CONFIG_BOOT=y
CONFIG_KEYBOARD=y
CONFIG_KBD_CALL_INT15_4F=y
CONFIG_MOUSE=y
CONFIG_S3_RESUME=y
# CONFIG_VGAHOOKS is not set
# CONFIG_DISABLE_A20 is not set
CONFIG_WRITABLE_UPPERMEMORY=y
# CONFIG_TCGBIOS is not set
#
# BIOS Tables
#
# CONFIG_PIRTABLE is not set
# CONFIG_MPTABLE is not set
# CONFIG_SMBIOS is not set
# CONFIG_ACPI is not set
# CONFIG_FW_ROMFILE_LOAD is not set
#
# VGA ROM
#
CONFIG_NO_VGABIOS=y
# CONFIG_VGA_STANDARD_VGA is not set
# CONFIG_VGA_CIRRUS is not set
# CONFIG_VGA_BOCHS is not set
# CONFIG_VGA_GEODEGX2 is not set
# CONFIG_VGA_GEODELX is not set
# CONFIG_BUILD_VGABIOS is not set
CONFIG_VGA_FIXUP_ASM=y
CONFIG_VGA_EXTRA_STACK_SIZE=512
#
# Debugging
#
CONFIG_DEBUG_LEVEL=0
