On Wed, Nov 19, 2014 at 8:59 PM, Christoffer Dall <christoffer.dall@xxxxxxxxxx> wrote: > On Tue, Nov 11, 2014 at 02:48:25PM +0530, Anup Patel wrote: >> Hi All, >> >> I have second thoughts about rebasing KVM PMU patches >> to Marc's irq-forwarding patches. >> >> The PMU IRQs (when virtualized by KVM) are not exactly >> forwarded IRQs because they are shared between Host >> and Guest. >> >> Scenario1 >> ------------- >> >> We might have perf running on Host and no KVM guest >> running. In this scenario, we wont get interrupts on Host >> because the kvm_pmu_hyp_init() (similar to the function >> kvm_timer_hyp_init() of Marc's IRQ-forwarding >> implementation) has put all host PMU IRQs in forwarding >> mode. >> >> The only way solve this problem is to not set forwarding >> mode for PMU IRQs in kvm_pmu_hyp_init() and instead >> have special routines to turn on and turn off the forwarding >> mode of PMU IRQs. These routines will be called from >> kvm_arch_vcpu_ioctl_run() for toggling the PMU IRQ >> forwarding state. >> >> Scenario2 >> ------------- >> >> We might have perf running on Host and Guest simultaneously >> which means it is quite likely that PMU HW trigger IRQ meant >> for Host between "ret = kvm_call_hyp(__kvm_vcpu_run, vcpu);" >> and "kvm_pmu_sync_hwstate(vcpu);" (similar to timer sync routine >> of Marc's patchset which is called before local_irq_enable()). >> >> In this scenario, the updated kvm_pmu_sync_hwstate(vcpu) >> will accidentally forward IRQ meant for Host to Guest unless >> we put additional checks to inspect VCPU PMU state. >> >> Am I missing any detail about IRQ forwarding for above >> scenarios? >> > Hi Anup, Hi Christoffer, > > I briefly discussed this with Marc. What I don't understand is how it > would be possible to get an interrupt for the host while running the > guest? > > The rationale behind my question is that whenever you're running the > guest, the PMU should be programmed exclusively with guest state, and > since the PMU is per core, any interrupts should be for the guest, where > it would always be pending. Yes, thats right PMU is programmed exclusively for guest when guest is running and for host when host is running. Let us assume a situation (Scenario2 mentioned previously) where both host and guest are using PMU. When the guest is running we come back to host mode due to variety of reasons (stage2 fault, guest IO, regular host interrupt, host interrupt meant for guest, ....) which means we will return from the "ret = kvm_call_hyp(__kvm_vcpu_run, vcpu);" statement in the kvm_arch_vcpu_ioctl_run() function with local IRQs disabled. At this point we would have restored back host PMU context and any PMU counter used by host can trigger PMU overflow interrup for host. Now we will be having "kvm_pmu_sync_hwstate(vcpu);" in the kvm_arch_vcpu_ioctl_run() function (similar to the kvm_timer_sync_hwstate() of Marc's IRQ forwarding patchset) which will try to detect PMU irq forwarding state in GIC hence it can accidentally discover PMU irq pending for guest while this PMU irq is actually meant for host. This above mentioned situation does not happen for timer because virtual timer interrupts are exclusively used for guest. The exclusive use of virtual timer interrupt for guest ensures that the function kvm_timer_sync_hwstate() will always see correct state of virtual timer IRQ from GIC. > > When migrating a VM with a pending PMU interrupt away for a CPU core, we > also capture the active state (the forwarding patches already handle > this), and obviously the PMU state along with it. Yes, the migration of PMU state and PMU interrupt state is quite clear. > > Does this address your concern? I hope above description give you idea about the concern raised by me. > > -Christoffer Regards, Anup -- To unsubscribe from this list: send the line "unsubscribe kvm" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
