> -----Original Message----- > From: Marc Zyngier [mailto:maz@xxxxxxxxxx] > Sent: 23 March 2021 16:23 > To: kvmarm@xxxxxxxxxxxxxxxxxxxxx; kvm@xxxxxxxxxxxxxxx; > linux-arm-kernel@xxxxxxxxxxxxxxxxxxx > Cc: Ard Biesheuvel <ardb@xxxxxxxxxx>; kernel-team@xxxxxxxxxxx; Shameerali > Kolothum Thodi <shameerali.kolothum.thodi@xxxxxxxxxx> > Subject: [PATCH] KVM: arm64: Fix CPU interface MMIO compatibility detection > > In order to detect whether a GICv3 CPU interface is MMIO capable, > we switch ICC_SRE_EL1.SRE to 0 and check whether it sticks. > > However, this is only possible if *ALL* of the HCR_EL2 interrupt > overrides are set, and the CPU is perfectly allowed to ignore > the write to ICC_SRE_EL1 otherwise. This leads KVM to pretend > that a whole bunch of ARMv8.0 CPUs aren't MMIO-capable, and > breaks VMs that should work correctly otherwise. > > Fix this by setting IMO/FMO/IMO before touching ICC_SRE_EL1, > and clear them afterwards. This allows us to reliably detect > the CPU interface capabilities. > Tested on HiSilicon D06 platform where the original issue(firmware wrongly advertising GICv2-on-v3 compatibility) was reported and all seems to be fine. Though not sure whether this fix is relevant to this particular platform, FWIW, Tested-by: Shameer Kolothum <shameerali.kolothum.thodi@xxxxxxxxxx> Thanks, Shameer > Cc: Shameerali Kolothum Thodi <shameerali.kolothum.thodi@xxxxxxxxxx> > Fixes: 9739f6ef053f ("KVM: arm64: Workaround firmware wrongly advertising > GICv2-on-v3 compatibility") > Signed-off-by: Marc Zyngier <maz@xxxxxxxxxx> > --- > arch/arm64/kvm/hyp/vgic-v3-sr.c | 9 +++++++++ > 1 file changed, 9 insertions(+) > > diff --git a/arch/arm64/kvm/hyp/vgic-v3-sr.c > b/arch/arm64/kvm/hyp/vgic-v3-sr.c > index ee3682b9873c..39f8f7f9227c 100644 > --- a/arch/arm64/kvm/hyp/vgic-v3-sr.c > +++ b/arch/arm64/kvm/hyp/vgic-v3-sr.c > @@ -429,6 +429,13 @@ u64 __vgic_v3_get_gic_config(void) > if (has_vhe()) > flags = local_daif_save(); > > + /* > + * Table 11-2 "Permitted ICC_SRE_ELx.SRE settings" indicates > + * that to be able to set ICC_SRE_EL1.SRE to 0, all the > + * interrupt overrides must be set. You've got to love this. > + */ > + sysreg_clear_set(hcr_el2, 0, HCR_AMO | HCR_FMO | HCR_IMO); > + isb(); > write_gicreg(0, ICC_SRE_EL1); > isb(); > > @@ -436,6 +443,8 @@ u64 __vgic_v3_get_gic_config(void) > > write_gicreg(sre, ICC_SRE_EL1); > isb(); > + sysreg_clear_set(hcr_el2, HCR_AMO | HCR_FMO | HCR_IMO, 0); > + isb(); > > if (has_vhe()) > local_daif_restore(flags); > -- > 2.30.0 _______________________________________________ kvmarm mailing list kvmarm@xxxxxxxxxxxxxxxxxxxxx https://lists.cs.columbia.edu/mailman/listinfo/kvmarm
