Re: [PATCH v7 10/25] ACPI / APEI: Tell firmware the estatus queue consumed the records

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Jan 29, 2019 at 06:48:33PM +0000, James Morse wrote:
> If firmware has never generated CPER records, so it has never written to void
> *error_status_address, yes.

I guess this is the bit of information I was missing.

> There seem to be two ways of doing this. This zero check implies an example
> system could be:
> | g->error_status_address == 0xf00d
> | *(u64 *)0xf00d == 0
> Firmware populates CPER records, then updates 0xf00d.
> (0xf00d would have been pre-mapped by apei_map_generic_address() in ghes_new())
> Reads of 0xf00d before CPER records are generated get 0.

Ok, this sounds like the polled case. FW better have a record ready
before raising the NMI.

> Once an error occurs, this system now looks like this:
> | g->error_status_address == 0xf00d
> | *(u64 *)0xf00d == 0xbeef
> | *(u64 *)0xbeef == 0
> 
> For new errors, firmware populates CPER records, then updates 0xf00d.
> Alternatively firmware could re-use the memory at 0xbeef, generating the CPER
> records backwards, so that once 0xbeef is updated, the rest of the record is
> visible. (firmware knows not to race with another CPU right?)

Thanks for the comic relief. :-P

> Firmware could equally point 0xf00d at 0xbeef at startup, so it has one fewer
> values to write when an error occurs. I have an arm64 system with a HEST that
> does this. (I'm pretty sure its ACPI support is a copy-and-paste from x86, it
> even describes NOTIFY_NMI, who knows what that means on arm!)

Oh the fun.

> When linux processes an error, ghes_clear_estatus() NULLs the
> estatus->block_status, (which in this example is at 0xbeef). This is the
> documented sequence for GHESv2.
> Elsewhere the spec talks of checking the block status which is part of the
> records, (not the error_status_address, which is the pointer to the records).
>
> Linux can't NULL 0xf00d, because it doesn't know if firmware will write it again
> next time it updates the records.
> I can't find where in the spec it says the error status address is written to.
> Linux works with both 'at boot' and 'on each error'.
> If it were know to have a static value, ghes_copy_tofrom_phys() would not have
> been necessary, but its been there since d334a49113a4.
>
> In the worst case, if there is a value at the error_status_address, we have to
> map/unmap it every time we poll in case firmware wrote new records at that same
> location.
> 
> I don't think we can change Linux's behaviour here, without interpreting zero as
> CPER records or missing new errors.

Nah, I was simply trying to figure out why we do that buf_paddr check.
Thanks for the extensive clarification.

-- 
Regards/Gruss,
    Boris.

Good mailing practices for 400: avoid top-posting and trim the reply.
_______________________________________________
kvmarm mailing list
kvmarm@xxxxxxxxxxxxxxxxxxxxx
https://lists.cs.columbia.edu/mailman/listinfo/kvmarm



[Index of Archives]     [Linux KVM]     [Spice Development]     [Libvirt]     [Libvirt Users]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux