The current timer test relies on testing the pending state of the timer
before the interrupt handler has run which could lower the pending
signal again (because it masks the timer output signal).
What we really want is to make sure the output signal from the timer as
perceived by the virtual interrupt controller is low when the timer is
programmed some time far in the future. The proper way to do that is to
disable the timer interrupt on the distributor and then reading its
pending state.
Signed-off-by: Christoffer Dall <cdall@xxxxxxxxxx>
---
arm/timer.c | 41 ++++++++++++++++++++++++++++++++++-------
1 file changed, 34 insertions(+), 7 deletions(-)
diff --git a/arm/timer.c b/arm/timer.c
index 33dfc6f..e824338 100644
--- a/arm/timer.c
+++ b/arm/timer.c
@@ -96,6 +96,23 @@ static struct timer_info ptimer_info = {
.write_ctl = write_ptimer_ctl,
};
+static void set_timer_irq_enabled(struct timer_info *info, bool enabled)
+{
+ u32 val = 0;
+
+ if (enabled)
+ val = 1 << PPI(info->irq);
+
+ switch (gic_version()) {
+ case 2:
+ writel(val, gicv2_dist_base() + GICD_ISENABLER + 0);
+ break;
+ case 3:
+ writel(val, gicv3_sgi_base() + GICR_ISENABLER0);
+ break;
+ }
+}
+
static void irq_handler(struct pt_regs *regs)
{
struct timer_info *info;
@@ -133,6 +150,8 @@ static bool test_cval_10msec(struct timer_info *info)
/* Program timer to fire in 10 ms */
before_timer = info->read_counter();
info->write_cval(before_timer + time_10ms);
+ info->write_ctl(ARCH_TIMER_CTL_ENABLE);
+ isb();
/* Wait for the timer to fire */
while (!(info->read_ctl() & ARCH_TIMER_CTL_ISTATUS))
@@ -159,13 +178,25 @@ static void test_timer(struct timer_info *info)
u64 time_10s = read_sysreg(cntfrq_el0) * 10;
u64 later = now + time_10s;
+ /* We don't want the irq handler to fire because that will change the
+ * timer state and we want to test the timer output signal. We can
+ * still read the pending state even if it's disabled. */
+ set_timer_irq_enabled(info, false);
- /* Enable the timer, but schedule it for much later*/
+ /* Enable the timer, but schedule it for much later */
info->write_cval(later);
- isb();
info->write_ctl(ARCH_TIMER_CTL_ENABLE);
-
+ isb();
report("not pending before", !gic_timer_pending(info));
+
+ info->write_cval(now - 1);
+ isb();
+ report("interrupt signal pending", gic_timer_pending(info));
+
+ /* Disable the timer again and prepare to take interrupts */
+ info->write_ctl(0);
+ set_timer_irq_enabled(info, true);
+
report("latency within 10 ms", test_cval_10msec(info));
report("interrupt received", info->irq_received);
@@ -211,13 +242,9 @@ static void test_init(void)
switch (gic_version()) {
case 2:
- writel(1 << PPI(vtimer_info.irq), gicv2_dist_base() + GICD_ISENABLER + 0);
- writel(1 << PPI(ptimer_info.irq), gicv2_dist_base() + GICD_ISENABLER + 0);
gic_ispendr = gicv2_dist_base() + GICD_ISPENDR;
break;
case 3:
- writel(1 << PPI(vtimer_info.irq), gicv3_sgi_base() + GICR_ISENABLER0);
- writel(1 << PPI(ptimer_info.irq), gicv3_sgi_base() + GICR_ISENABLER0);
gic_ispendr = gicv3_sgi_base() + GICD_ISPENDR;
break;
}
--
2.9.0
_______________________________________________
kvmarm mailing list
kvmarm@xxxxxxxxxxxxxxxxxxxxx
https://lists.cs.columbia.edu/mailman/listinfo/kvmarm
