Re: [PATCH] Documentation: kdump: update kdump guide

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Baoquan,
On 05/26/21 at 03:11pm, Baoquan He wrote:
> On 05/25/21 at 07:41pm, Dave Young wrote:
> > Hi Baoquan,
> > > @@ -180,7 +191,7 @@ Dump-capture kernel config options (Arch Dependent, i386 and x86_64)
> > >  
> > >  	CONFIG_SMP=n
> > >  
> > > -   (If CONFIG_SMP=y, then specify maxcpus=1 on the kernel command line
> > > +   (If CONFIG_SMP=y, then specify nr_cpus=1 on the kernel command line
> > >     when loading the dump-capture kernel, see section "Load the Dump-capture
> > >     Kernel".)
> > 
> > This part should be obsolete?  Since for X86_64 we can enable smp boot
> > with disable_cpu_apicid=X set (see the Notes on loading the dump-capture
> > kernel part)  So I think no need to disable CONFIG_SMP at all.  The
> > current RHEL use of nr_cpus=1 is just to save 2nd kernel memory use.
> 
> Keeping them because they are not wrong. Talking about default config,
> currently we only care about x86_64 mostly, not sure if we should remove
> i386 part too. Anyway, I am fine to remove them and the below
> relocatable thing.

I also agree it is not wrong :)  But I personally think the doc should
target for the most common use cases.  If CONFIG_SMP=n is not common
then we may just describe the default words for CONFIG_SMP=y,  and we
may add some words for exection cases

for example:
Specify nr_cpus=1 blabla
Note: if CONFIG_SMP is not set then nr_cpus=1 is not needed ...


> 
> > 
> > Ditto for the text for other arches, not sure if they need update
> > though, see if other maintainers can provide inputs..
> > 
> > 
> > Otherwise for the CONFIG_RELOCATABLE related part,  it may be better to
> > update as well? 
> > ''' quote:
> > 3) If one wants to build and use a relocatable kernel,
> >    Enable "Build a relocatable kernel" support under "Processor type and
> >    features"::
> > 
> >         CONFIG_RELOCATABLE=y
> > 
> > 4) Use a suitable value for "Physical address where the kernel is
> >    loaded" (under "Processor type and features"). This only appears when
> >    "kernel crash dumps" is enabled. A suitable value depends upon
> >    whether kernel is relocatable or not.
> > 
> >    If you are using a relocatable kernel use CONFIG_PHYSICAL_START=0x100000
> >    This will compile the kernel for physical address 1MB, but given the fact
> >    kernel is relocatable, it can be run from any physical address hence
> >    kexec boot loader will load it in memory region reserved for dump-capture
> >    kernel.
> > 
> >    Otherwise it should be the start of memory region reserved for
> >    second kernel using boot parameter "crashkernel=Y@X". Here X is
> >    start of memory region reserved for dump-capture kernel.
> >    Generally X is 16MB (0x1000000). So you can set
> >    CONFIG_PHYSICAL_START=0x1000000
> > ''' end quote
> > 
> > Since relocatable kernel is used by default now so we may just not describe it as "If one
> > want to build with it =y", I feel it should be a corner case instead of
> > the default use case.   Maybe HPA, Vivek, Eric can provide more opinions since
> > they may know more about the background.  
> > 
> > >  
> ...  
> > > -Boot into System Kernel
> > > -=======================
> > > +       crashkernel=512M-2G:64M,2G-:128M
> > >  
> > > +   This would mean:
> > > +
> > > +       1) if the RAM is smaller than 512M, then don't reserve anything
> > > +          (this is the "rescue" case)
> > > +       2) if the RAM size is between 512M and 2G (exclusive), then reserve 64M
> > > +       3) if the RAM size is larger than 2G, then reserve 128M
> > > +
> > > +3) crashkernel=size,high and crashkernel=size,low
> > > +
> > > +   If memory above 4G is preferred, crashkernel=size,high can be used to
> > > +   fulfill that. With it, physical memory is allowed to allocate from top,
> > > +   so could be above 4G if system has more than 4G RAM installed. Otherwise,
> > > +   memory region will be allocated below 4G if available.
> > > +
> > > +   When crashkernel=X,high is passed, kernel could allocate physical memory
> > > +   region above 4G, low memory under 4G is needed in this case. There are
> > > +   three ways to get low memory:
> > > +
> > > +      1) Kernel will allocate at least 256M memory below 4G automatically
> > > +         if crashkernel=Y,low is not specified.
> > > +      2) Let user specify low memory size instread.
> > > +      3) Specified value 0 will disable low memory allocation::
> > > +
> > > +            crashkernel=0,low
> > > +
> > > +Boot into System Kernel
> > > +-----------------------
> > >  1) Update the boot loader (such as grub, yaboot, or lilo) configuration
> > >     files as necessary.
> > >  
> > > -2) Boot the system kernel with the boot parameter "crashkernel=Y@X",
> > > -   where Y specifies how much memory to reserve for the dump-capture kernel
> > > -   and X specifies the beginning of this reserved memory. For example,
> > > -   "crashkernel=64M@16M" tells the system kernel to reserve 64 MB of memory
> > > -   starting at physical address 0x01000000 (16MB) for the dump-capture kernel.
> > > +2) Boot the system kernel with the boot parameter "crashkernel=Y@X".
> > >  
> > >     On x86 and x86_64, use "crashkernel=64M@16M".
> > 
> > For the recommendation of crashkernel it would be better to drop the
> > @16M since most people do not need it?
> 
> It's only an example? Change it as "crashkernel=128M" instead to make it
> more helpful?

Hmm, it would be better to make the most common use case in default
example, and put the corner cases on corner :)

> 
> > 
> > >  
> > > @@ -392,7 +432,7 @@ loading dump-capture kernel.
> > >  
> > >  For i386, x86_64 and ia64:
> > >  
> > > -	"1 irqpoll maxcpus=1 reset_devices"
> > > +	"1 irqpoll nr_cpus=1 reset_devices"
> > >  
> > >  For ppc64:
> > >  
> > > @@ -400,7 +440,7 @@ For ppc64:
> > >  
> > >  For s390x:
> > >  
> > > -	"1 maxcpus=1 cgroup_disable=memory"
> > > +	"1 nr_cpus=1 cgroup_disable=memory"
> > >  
> > >  For arm:
> > >  
> > > @@ -408,7 +448,7 @@ For arm:
> > >  
> > >  For arm64:
> > >  
> > > -	"1 maxcpus=1 reset_devices"
> > > +	"1 nr_cpus=1 reset_devices"
> > >  
> > >  Notes on loading the dump-capture kernel:
> > >  
> > > @@ -487,7 +527,12 @@ After the dump-capture kernel is booted, write out the dump file with
> > >  the following command::
> > >  
> > >     cp /proc/vmcore <dump-file>
> > > +   scp /proc/vmcore to <user@server>:<path>/%HOST-%DATE/
> > > +
> > > +You can also use makedumpfile utility to write out the dump file
> > > +with specified options to filter out unwanted contents, e.g::
> > >  
> > > +   core_collector makedumpfile -l --message-level 1 -d 31
> > 
> > Looks like scp and core_collector usage are based on Fedora/RHEL, but
> > since this doc is for generic upstream, it might be better to describe
> > it in generic way, eg.  (maybe just drop scp)
> >   makedumpfile -l --message-level 1 -d 31 /proc/vmcore <dump-file>
> >   scp /proc/vmcore <user@server>:<path>/<dump-file>
> 
> Right, forgot removing core_collector. While scp is also a generic tool?

scp is good to have, just it is similar to cp, as these are just
examples I'm fine for either.

If taking scp then just drop the " to" and %HOST_%DATE/  etc.

> 
> Thanks for reviewing.
> 

Thanks
Dave


_______________________________________________
kexec mailing list
kexec@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/kexec



[Index of Archives]     [LM Sensors]     [Linux Sound]     [ALSA Users]     [ALSA Devel]     [Linux Audio Users]     [Linux Media]     [Kernel]     [Gimp]     [Yosemite News]     [Linux Media]

  Powered by Linux