This version works for 3.19.0-rc1. Zhenhua On 12/22/2014 05:15 PM, Li, Zhen-Hua wrote: > This patchset is an update of Bill Sumner's patchset, implements a fix for: > If a kernel boots with intel_iommu=on on a system that supports intel vt-d, > when a panic happens, the kdump kernel will boot with these faults: > > dmar: DRHD: handling fault status reg 102 > dmar: DMAR:[DMA Read] Request device [01:00.0] fault addr fff80000 > DMAR:[fault reason 01] Present bit in root entry is clear > > dmar: DRHD: handling fault status reg 2 > dmar: INTR-REMAP: Request device [[61:00.0] fault index 42 > INTR-REMAP:[fault reason 34] Present field in the IRTE entry is clear > > On some system, the interrupt remapping fault will also happen even if the > intel_iommu is not set to on, because the interrupt remapping will be enabled > when x2apic is needed by the system. > > The cause of the DMA fault is described in Bill's original version, and the > INTR-Remap fault is caused by a similar reason. In short, the initialization > of vt-d drivers causes the in-flight DMA and interrupt requests get wrong > response. > > To fix this problem, we modifies the behaviors of the intel vt-d in the > crashdump kernel: > > For DMA Remapping: > 1. To accept the vt-d hardware in an active state, > 2. Do not disable and re-enable the translation, keep it enabled. > 3. Use the old root entry table, do not rewrite the RTA register. > 4. Malloc and use new context entry table and page table, copy data from the > old ones that used by the old kernel. > 5. to use different portions of the iova address ranges for the device drivers > in the crashdump kernel than the iova ranges that were in-use at the time > of the panic. > 6. After device driver is loaded, when it issues the first dma_map command, > free the dmar_domain structure for this device, and generate a new one, so > that the device can be assigned a new and empty page table. > 7. When a new context entry table is generated, we also save its address to > the old root entry table. > > For Interrupt Remapping: > 1. To accept the vt-d hardware in an active state, > 2. Do not disable and re-enable the interrupt remapping, keep it enabled. > 3. Use the old interrupt remapping table, do not rewrite the IRTA register. > 4. When ioapic entry is setup, the interrupt remapping table is changed, and > the updated data will be stored to the old interrupt remapping table. > > Advantages of this approach: > 1. All manipulation of the IO-device is done by the Linux device-driver > for that device. > 2. This approach behaves in a manner very similar to operation without an > active iommu. > 3. Any activity between the IO-device and its RMRR areas is handled by the > device-driver in the same manner as during a non-kdump boot. > 4. If an IO-device has no driver in the kdump kernel, it is simply left alone. > This supports the practice of creating a special kdump kernel without > drivers for any devices that are not required for taking a crashdump. > 5. Minimal code-changes among the existing mainline intel vt-d code. > > Summary of changes in this patch set: > 1. Added some useful function for root entry table in code intel-iommu.c > 2. Added new members to struct root_entry and struct irte; > 3. Functions to load old root entry table to iommu->root_entry from the memory > of old kernel. > 4. Functions to malloc new context entry table and page table and copy the data > from the old ones to the malloced new ones. > 5. Functions to enable support for DMA remapping in kdump kernel. > 6. Functions to load old irte data from the old kernel to the kdump kernel. > 7. Some code changes that support other behaviours that have been listed. > 8. In the new functions, use physical address as "unsigned long" type, not > pointers. > > Original version by Bill Sumner: > https://lkml.org/lkml/2014/1/10/518 > https://lkml.org/lkml/2014/4/15/716 > https://lkml.org/lkml/2014/4/24/836 > > Zhenhua's last of Bill's patchset: > https://lkml.org/lkml/2014/10/21/134 > https://lkml.org/lkml/2014/12/15/121 > > Changed in this version: > 1. Do not disable and re-enable traslation and interrupt remapping. > 2. Use old root entry table. > 3. Use old interrupt remapping table. > 4. Use "unsigned long" as physical address. > 5. Use intel_unmap to unmap the old dma; > > This patchset should be applied with this one together: > https://lkml.org/lkml/2014/11/5/43 > x86/iommu: fix incorrect bit operations in setting values > > Bill Sumner (5): > iommu/vt-d: Update iommu_attach_domain() and its callers > iommu/vt-d: Items required for kdump > iommu/vt-d: data types and functions used for kdump > iommu/vt-d: Add domain-id functions > iommu/vt-d: enable kdump support in iommu module > > Li, Zhen-Hua (10): > iommu/vt-d: Update iommu_attach_domain() and its callers > iommu/vt-d: Items required for kdump > iommu/vt-d: Add domain-id functions > iommu/vt-d: functions to copy data from old mem > iommu/vt-d: Add functions to load and save old re > iommu/vt-d: datatypes and functions used for kdump > iommu/vt-d: enable kdump support in iommu module > iommu/vtd: assign new page table for dma_map > iommu/vt-d: Copy functions for irte > iommu/vt-d: Use old irte in kdump kernel > > drivers/iommu/intel-iommu.c | 1050 +++++++++++++++++++++++++++++++++-- > drivers/iommu/intel_irq_remapping.c | 99 +++- > include/linux/intel-iommu.h | 18 + > 3 files changed, 1123 insertions(+), 44 deletions(-) >