On Tue, Jan 05, 2016 at 02:53:08PM -0500, Lyude wrote:
> There's no reason to check for an active encoder when setting up hpd,
> especially since a disconnected connector isn't going to have an encoder
> in the first place. This fixes reprobing display connectors on resume.
>
> Signed-off-by: Lyude <cpaul@xxxxxxxxxx>
> ---
> After some talking with danvet on IRC, I learned that calling
> drm_helper_hpd_irq_event() does actually trigger a full reprobe of each
> connector's status. It turns out this is the actual reason reprobing on resume
> hasn't been working (this was observed on a T440s):
>
> - We call hpd_init()
> - We check each connector for a couple of things before marking
> connector->polled with DRM_CONNECTOR_POLL_HPD, one of which is an
> active encoder. Of course, a disconnected port won't have an active
> encoder, so we don't add the flag to any of the connector's.
> - We call drm_helper_hpd_irq_event()
> - drm_helper_irq_event() checks each connector for the
> DRM_CONNECTOR_POLL_HPD flag. The only one that has it is eDP-1, so we
> skip reprobing each connector except that one.
The above explanation should be part of the commit message, otherwise it's
hard to understand the impact of this fix.
Fixes: 0e32b39ceed6 ("drm/i915: add DP 1.2 MST support (v0.7)")
Cc: stable@xxxxxxxxxxxxxxx
Unfortunately Dave doesn't explain in his MST commit why he's done this.
Dave? I can't come up with a reason, but better to test that. Lyude?
Anyway looks good to me.
Reviewed-by: Daniel Vetter <daniel.vetter@xxxxxxxx>
>
> drivers/gpu/drm/i915/intel_hotplug.c | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/drivers/gpu/drm/i915/intel_hotplug.c b/drivers/gpu/drm/i915/intel_hotplug.c
> index b177857..18797bc 100644
> --- a/drivers/gpu/drm/i915/intel_hotplug.c
> +++ b/drivers/gpu/drm/i915/intel_hotplug.c
> @@ -468,7 +468,7 @@ void intel_hpd_init(struct drm_i915_private *dev_priv)
> list_for_each_entry(connector, &mode_config->connector_list, head) {
> struct intel_connector *intel_connector = to_intel_connector(connector);
> connector->polled = intel_connector->polled;
> - if (connector->encoder && !connector->polled && I915_HAS_HOTPLUG(dev) && intel_connector->encoder->hpd_pin > HPD_NONE)
> + if (!connector->polled && I915_HAS_HOTPLUG(dev) && intel_connector->encoder->hpd_pin > HPD_NONE)
> connector->polled = DRM_CONNECTOR_POLL_HPD;
> if (intel_connector->mst_port)
> connector->polled = DRM_CONNECTOR_POLL_HPD;
> --
> 2.5.0
>
> _______________________________________________
> Intel-gfx mailing list
> Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
> http://lists.freedesktop.org/mailman/listinfo/intel-gfx
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
